Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0110870 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P0571  Brake Switch "A" Circuit  


DESCRIPTION

·

When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. When the ECM receives this signal, it cancels the dynamic radar cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM turns the dynamic radar cruise control system off.

·

The ECM receives the brake demand signal from the driving support ECU assembly and sends it to the skid control ECU (brake actuator assembly). The skid control ECU (brake actuator assembly) receives the signal from the ECM and operates the skid control ECU (brake actuator assembly). The skid control ECU (brake actuator assembly) operates the brake actuator and at the same time illuminates the stop lights by operating the stop light switch assembly (stop light control relay).


DTC No. Detection Item DTC Detection Condition Trouble Area
P0571 Brake Switch "A" Circuit (Condition 1)
·

Voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for approximately 0.5 seconds or more.


(Condition 2)
·

The ECM detects the stop light switch assembly (stop light control relay) error signal from the skid control ECU (brake actuator assembly) for approximately 0.2 seconds or more while the dynamic radar cruise control is operating.


(Condition 1)
·

Stop light switch assembly

·

Stop light switch circuit

·

ECM


(Condition 2)
·

Stop light switch assembly

·

Stop light switch circuit

·

Skid control ECU (brake actuator assembly)



WIRING DIAGRAM

E287461
2.667,1.354 3.844,1.823 1.177,0.469 10 false Stop Light Switch Assembly 2.74,3.771 3.406,4.042 0.667,0.271 10 false STOP LP 5.615,1.479 6.146,1.781 0.531,0.302 10 false ECM 5.271,3.938 6.813,4.354 1.542,0.417 10 false Skid Control ECU (Brake Actuator Assembly) 3.396,0.323 3.646,0.552 0.25,0.229 10 false 1 3.427,2.844 3.677,3.073 0.25,0.229 10 false 3 3.438,2.5 3.688,2.729 0.25,0.229 10 false 4 2.635,2.833 2.885,3.063 0.25,0.229 10 false 5 2.625,3.313 2.875,3.542 0.25,0.229 10 false 2 5.521,2.615 6.021,2.896 0.5,0.281 10 false STP2 5.531,2.948 6.01,3.188 0.479,0.24 10 false STP 5.542,3.417 6.021,3.656 0.479,0.24 10 false STPO 5.531,0.865 6.042,1.115 0.51,0.25 10 false ST1- 5.531,0.438 6.042,0.688 0.51,0.25 10 false STP 2.604,0.729 2.854,0.958 0.25,0.229 10 false 4 3.396,0.74 3.646,0.969 0.25,0.229 10 false 3 3.438,3.313 3.688,3.542 0.25,0.229 10 false 1 2.594,0.323 2.76,0.521 0.167,0.198 10 false 2 1.833,3.583 2.573,3.844 0.74,0.26 10 false IG1 NO. 2 2,3.104 2.438,3.365 0.438,0.26 10 false STOP 5.615,1.292 6.063,1.49 0.448,0.198 10 false A43 5.281,3.719 5.729,3.917 0.448,0.198 10 false A47 2.667,1.146 3.115,1.344 0.448,0.198 10 false A54 0.563,4.24 1.521,4.521 0.958,0.281 10 false to Stop Lights 5.323,3.323 5.521,3.521 0.198,0.198 10 false 31 5.302,2.521 5.479,2.74 0.177,0.219 10 false 22 5.385,2.833 5.521,3.073 0.135,0.24 10 false 2 5.313,0.344 5.521,0.563 0.208,0.219 10 false 51 5.323,0.729 5.542,0.969 0.219,0.24 10 false 36 0.521,0.813 1.458,1.073 0.938,0.26 10 false from IG2 Fuse 0.635,2.917 1.448,3.229 0.813,0.313 10 false from Battery 0.458,3.417 1.406,3.833 0.948,0.417 10 false from IG1 NO. 3 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (STOP LIGHT SWITCH1, STOP LIGHT SWITCH2, BRAKE CANCEL SWITCH)

NG

2.READ VALUE USING GTS (STOP LIGHT SWITCH1, STOP LIGHT SWITCH2, BRAKE CANCEL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Radar Cruise / Data List.


e.

Check the Data List for proper functioning of the stop light switch.

Powertrain > Radar Cruise > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch 1 Stop light switch signal ON or OFF OK: Brake pedal depressed
OFF: Brake pedal released
-
Stop Light Switch 2 Stop light switch signal ON or OFF OK: Brake pedal depressed
OFF: Brake pedal released
-
Brake Cancel Switch Brake cancel signal ON or OFF OK: Brake pedal depressed
OFF: Brake pedal released
-
Powertrain > Radar Cruise > Data List
Tester Display
Stop Light Switch 1
Stop Light Switch 2
Brake Cancel Switch
50003 239 17,18,48
OK:

Display changes according to brake pedal operation described in the table.



Result:
Proceed to
OK
NG


f.

Turn the engine switch off.



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SKID CONTROL ECU)

NG

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE)
3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SKID CONTROL ECU)
a.

Disconnect the A54 stop light switch assembly connector.


b.

Disconnect the A47 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A54-1 - A47-22 (STP2) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A54-1 or A47-22 (STP2) - Body ground Always 10 kΩ or higher



d.

Reconnect the A47 skid control ECU (brake actuator assembly) connector.


e.

Reconnect the A54 stop light switch assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (STOP LP RELAY - SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SKID CONTROL ECU AND ECM)

4.CHECK HARNESS AND CONNECTOR (STOP LP RELAY - SKID CONTROL ECU)
a.

Remove the STOP LP relay from the engine room relay block and junction block assembly.


b.

Disconnect the A47 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
Relay terminal 1 - A47-31 (STPO) Always Below 1 Ω
Relay terminal 4 - A47-22 (STP2) Always Below 1 Ω
Relay terminal 3 - A47-2 (STP) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
Relay terminal 1 or A47-31 (STPO) - Body ground Always 10 kΩ or higher
Relay terminal 4 or A47-22 (STP2) - Body ground Always 10 kΩ or higher
Relay terminal 3 or A47-2 (STP) - Body ground Always 10 kΩ or higher



d.

Reinstall the STOP LP relay to the engine room relay block and junction block assembly.


e.

Reconnect the A47 skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

5.INSPECT STOP LP RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LP RELAY - SKID CONTROL ECU)

5.INSPECT STOP LP RELAY
a.

Remove the STOP LP relay from the engine room relay block and junction block assembly.


b.
E289678
2.115,0.708 2.021,0.219 2.021,0.219 1.698,0.219 true 2.656,0.708 2.729,0.229 2.729,0.229 3.052,0.229 true 3.031,1.24 2.448,1.24 2.448,1.24 2.385,1.052 true 3.01,2.042 2.479,2.042 2.479,2.042 2.396,1.792 true 3.021,1.583 2.438,1.583 2.438,1.583 2.375,1.396 true 0.083,0.063 0.344,0.292 0.26,0.229 10 false *1 0.896,0.219 1.063,0.417 0.167,0.198 10 false 4 0.385,0.885 0.552,1.083 0.167,0.198 10 false 5 0.385,1.688 0.552,1.885 0.167,0.198 10 false 2 1.354,0.885 1.51,1.104 0.156,0.219 10 false 3 1.354,1.677 1.542,1.896 0.188,0.219 10 false 1 1.594,0.156 1.781,0.375 0.188,0.219 10 false 1 3.052,1.948 3.281,2.146 0.229,0.198 10 false 3 3.063,1.51 3.229,1.708 0.167,0.198 10 false 5 3.073,1.167 3.24,1.365 0.167,0.198 10 false 4 3.094,0.156 3.26,0.354 0.167,0.198 10 false 2
*1 STOP LP Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery voltage not applied between terminals 1 and 2 Below 1 Ω
Battery voltage applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω



c.

Reinstall the STOP LP relay to the engine room relay block and junction block assembly.


Result:
Proceed to
OK
NG



OK

6.REPLACE BRAKE ACTUATOR ASSEMBLY

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

6.REPLACE BRAKE ACTUATOR ASSEMBLY
a.

Replace the brake actuator assembly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTCS (DTC P0571)
7.CHECK FOR DTCS (DTC P0571)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).



d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which cruise control operation is possible.


ii.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).


iii.

Push the cruise control main switch to -SET to activate the dynamic radar cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.

Powertrain > Radar Cruise > Trouble Codes
50001 239

Result:
Result Proceed to
DTCs are not output A
DTC P0571 is output B


g.

Turn the engine switch off.



A

END

B

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE)
a.

Disconnect the A54 stop light switch assembly connector.


b.
E287468
1.51,0.323 2.01,0.604 0.5,0.281 0.177,0.125 0.427,0.323 0.25,0.198 10 false *a 1.635,0.375 1.927,0.583 0.292,0.208 10 false A54
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A54-2 - Body ground Always 11 to 14 V



c.

Reconnect the A54 stop light switch assembly connector.


Result:
Proceed to
OK
NG



OK

9.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE)

9.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the A54 stop light switch assembly connector.


b.

Disconnect the A43 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A54-3 - A43-36 (ST1-) Always Below 1 Ω
A54-1 - A43-51 (STP) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A54-3 or A43-36 (ST1-) - Body ground Always 10 kΩ or higher
A54-1 or A43-51 (STP) - Body ground Always 10 kΩ or higher



d.

Reconnect the A54 stop light switch assembly connector.


e.

Reconnect the A43 ECM connector.


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

11.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the A54 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A54-1 - Body ground Always 10 kΩ or higher
A54-3 - Body ground Always 10 kΩ or higher



c.

Reconnect the A54 stop light switch assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)