Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2013.12–2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0110870 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P1575  Warning Buzzer Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives an alarm demand signal from the driving support ECU assembly and operates the skid control buzzer assembly. The buzzer sounds to warn that the distance between the vehicle in front and this vehicle is decreasing.

DTC No. Detection Item DTC Detection Condition Trouble Area
P1575 Warning Buzzer Malfunction The ECM receives a buzzer abnormal signal for approximately 0.2 seconds or more while the dynamic radar cruise control is operating.
·

Skid control buzzer assembly

·

Skid control buzzer circuit

·

Skid control ECU (brake actuator assembly)

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

ECM



HINT:

If the vehicle ahead in the same lane significantly decreases its speed or another vehicle moves in front of this vehicle, adequate deceleration cannot be applied and the vehicle-to-vehicle distance will shorten. At this time, the system sounds the buzzer and the master warning light blinks to inform the driver. This circuit uses CAN communication. Therefore, if there are any malfunctions in the communication circuit, one or more CAN communication system DTCs are stored.


WIRING DIAGRAM

E287462
4.333,1.417 5.646,1.906 1.313,0.49 10 false Driving Support ECU Assembly 2.688,1.427 4.094,2.01 1.406,0.583 10 false Millimeter Wave Radar Sensor Assembly 3.74,3.01 5.26,3.417 1.521,0.406 10 false Lane Departure Warning Camera* 3.021,2.479 3.167,2.667 0.146,0.188 10 false * 0.719,3.427 2.396,3.719 1.677,0.292 10 false : CAN Communication Line 0.25,3.021 2.396,3.365 2.146,0.344 10 false *: w/ Lane Departure Alert System 0.938,1.25 2.198,1.771 1.26,0.521 10 false Skid Control Buzzer Assembly 3.271,0.448 3.688,0.677 0.417,0.229 10 false CA1P 4.365,0.885 4.781,1.115 0.417,0.229 10 false CA1N 3.26,0.906 3.677,1.135 0.417,0.229 10 false CA1N 4.365,0.438 4.781,0.667 0.417,0.229 10 false CA1P 2.844,0.635 3.073,0.854 0.229,0.219 10 false BZ 1.594,0.625 1.823,0.844 0.229,0.219 10 false BZ 3.823,2.375 4.052,2.594 0.229,0.219 10 false BZ 1.198,0.635 1.5,0.854 0.302,0.219 10 false IG1 0.948,1.063 1.25,1.281 0.302,0.219 10 false A59 2.677,1.229 2.979,1.448 0.302,0.219 10 false A3 4.344,1.24 4.646,1.458 0.302,0.219 10 false F84 3.74,2.833 4.042,3.052 0.302,0.219 10 false S4 3.646,2.24 3.813,2.458 0.167,0.219 10 false 8 2.604,0.51 2.771,0.729 0.167,0.219 10 false 10 1.854,0.521 2.021,0.74 0.167,0.219 10 false 1 1.042,0.531 1.208,0.75 0.167,0.219 10 false 2 3.698,0.26 3.865,0.479 0.167,0.219 10 false 3 3.708,0.75 3.875,0.969 0.167,0.219 10 false 2 5.292,0.74 5.479,0.927 0.188,0.188 10 false 17 4.125,0.719 4.354,0.917 0.229,0.198 10 false 18 0.104,0.615 0.729,1.219 0.625,0.604 10 false From IG1 NO. 3 Fuse 6.021,1.427 6.49,1.708 0.469,0.281 10 false ECM 6,1.24 6.302,1.458 0.302,0.219 10 false A43 5.75,0.26 5.99,0.479 0.24,0.219 10 false 13 5.76,0.76 6,0.979 0.24,0.219 10 false 26 5.979,0.417 6.594,0.677 0.615,0.26 10 false CANH 4.896,0.875 5.313,1.104 0.417,0.229 10 false CA2L 4.875,0.427 5.292,0.656 0.417,0.229 10 false CA2H 5.979,0.875 6.396,1.104 0.417,0.229 10 false CANL 4.135,0.24 4.375,0.458 0.24,0.219 10 false 40 5.281,0.24 5.521,0.458 0.24,0.219 10 false 39

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SKID CONTROL BUZZER ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test


e.

Perform "Active Test" according to the display on the GTS.

Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Radar Cruise Approach Alarm Buzzer Skid control buzzer assembly ON or OFF Buzzer can be heard
Body Electrical > Pre-Crash 2 > Active Test
Tester Display
Radar Cruise Approach Alarm Buzzer
50004 220 4
OK:

Skid control buzzer assembly sounds.



Result:
Proceed to
OK
NG


f.

Turn the engine switch off.



OK

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

2.INSPECT SKID CONTROL BUZZER ASSEMBLY
2.INSPECT SKID CONTROL BUZZER ASSEMBLY
a.

Remove the skid control buzzer assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT BUZZER>REMOVAL


b.

Inspect the skid control buzzer assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT BUZZER>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SKID CONTROL BUZZER ASSEMBLY)

NG

REPLACE SKID CONTROL BUZZER ASSEMBLY

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SKID CONTROL BUZZER ASSEMBLY)
a.
B338290
0.542,1.198 0.938,1.458 0.396,0.26 2.396,2 2.146,2 2.146,2 1.875,1.604 true 0.063,0.094 0.323,0.229 0.26,0.135 10 false *a 0.615,1.229 0.969,1.438 0.354,0.208 10 false A59 2.448,1.917 2.896,2.135 0.448,0.219 10 false IG1
*a Front view of wire harness connector
(to Skid Control Buzzer Assembly)


Disconnect the A59 skid control buzzer assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A59-2 (IG1) - Body ground Engine switch on (IG) 11 to 14 V
A59-2 (IG1) - Body ground Engine switch off Below 1 V



c.

Reconnect the A59 skid control buzzer assembly connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - BATTERY)

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the A59 skid control buzzer assembly connector.


b.

Disconnect the A3 millimeter wave radar sensor assembly connector.


c.

Disconnect the S4 lane departure warning camera connector (w/ Lane Departure Alert System).


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A59-1 (BZ) - A3-10 (BZ) Always Below 1 Ω
A59-1 (BZ) or A3-10 (BZ) - Body ground Always 10 kΩ or higher



e.

Reconnect the S4 lane departure warning camera connector (w/ Lane Departure Alert System).


f.

Reconnect the A3 millimeter wave radar sensor assembly connector.


g.

Reconnect the A59 skid control buzzer assembly connector.


Result:
Proceed to
OK
NG



OK

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCs (RADAR CRUISE)
6.CHECK FOR DTCs (RADAR CRUISE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).



d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which cruise control operation is possible.


ii.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).


iii.

Push the cruise control main switch to -SET to activate the dynamic radar cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.

Powertrain > Radar Cruise > Trouble Codes
50001 239
NOTICE:

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



Result:
Result Proceed to
DTC P1575 is not output A
DTC P1575 is output B


g.

Turn the engine switch off.



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

7.REPLACE DRIVING SUPPORT ECU ASSEMBLY
7.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU(for RHD)>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTCs (RADAR CRUISE)
8.CHECK FOR DTCs (RADAR CRUISE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).



d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which cruise control operation is possible.


ii.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).


iii.

Push the cruise control main switch to -SET to activate the dynamic radar cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.

Powertrain > Radar Cruise > Trouble Codes
50001 239
NOTICE:

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



Result:
Result Proceed to
DTC P1575 is not output A
DTC P1575 is output B


g.

Turn the engine switch off.



A

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

B