Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR › from 2015.11
RM3160E _58 Vehicle Interior _019710 SUPPLEMENTAL RESTRAINT SYSTEMS _0109995 REAR AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  REAR AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89834 1.INSTALL REAR AIRBAG SENSOR

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

B296256C01
5.01,0.51 5.302,0.781 0.292,0.271 10 *b 1.792,0.51 2.083,0.802 0.292,0.292 10 *a
*a Correct *b Incorrect



d.

Insert the rear airbag sensor pin (stopper) into the body hole and install the rear airbag sensor to the vehicle body with the nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the rear airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Make sure that the rear airbag sensor pin (stopper) is securely inserted into the body hole.

·

Tighten the nut while holding the rear airbag sensor because the rear airbag sensor pin (stopper) is easily damaged.




e.

Connect the connector to the rear airbag sensor.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


i.

Be sure to engage the connector until it is locked (when locking, make sure that a click sound can be heard).

C198070C15
3.719,1.219 4.156,1.583 true 1.51,0.927 0.99,0.531 true 3.479,1.146 2.958,0.75 true 5.875,1.448 6.313,1.813 true 4.177,1.604 4.354,1.771 0.177,0.167 10 false *a 3.573,1.74 3.76,1.885 0.188,0.146 10 false *b 6.354,1.833 6.542,1.979 0.188,0.146 10 false *a 0.854,0.438 1.146,0.656 0.292,0.219 10 false A 2.813,0.635 3.104,0.854 0.292,0.219 10 false A
*a White Housing Lock *b Engage


HINT:

When engaged, the white housing lock will slide. Be sure not to hold the white housing lock or part (A), as it may result in an insecure fit.




f.

Check that there is no looseness in the installed parts of the rear airbag sensor.


Hide 64740C 2.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)

Hide 64730B 3.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)

Hide 64725F 5.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

Hide 64974 6.INSTALL DECK TRIM POCKET COVER

Hide 81330 7.INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for RH Side)

Hide 62627D 8.INSTALL SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)

Hide 88625T 9.INSTALL COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR (w/ Rear Automatic Air Conditioning System)

Hide 73570 10.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY

Hide 64715E 11.INSTALL NO. 2 DECK SIDE TRIM COVER (for LH Side)

Hide 64714H 12.INSTALL NO. 1 DECK SIDE TRIM COVER (for RH Side)

Hide 73370C 13.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY

Hide 64713F 14.INSTALL FRONT DECK SIDE TRIM COVER

Hide 15.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 67918A 16.INSTALL REAR DOOR SCUFF PLATE

Hide 72138M 17.INSTALL REAR OUTER SEAT TRACK BRACKET COVER

Hide 58387B 18.INSTALL REAR FLOOR FINISH PLATE

Hide 19.INSTALL REAR NO. 2 SEAT ASSEMBLY

Hide 20.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION