Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB › from 2016.11
RM3160E _52 Drivetrain _019687 AXLE AND DIFFERENTIAL _0107975 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 89543 3.SEPARATE FRONT SPEED SENSOR

a.
C291618C01
1.646,1.854 1.823,1.854 1.823,1.854 2.031,1.573 true 1.479,1.771 1.646,1.948 0.167,0.177 10 true *a
*a Sensor Clamp


Disengage the 2 claws and separate the sensor clamp.


b.

Remove the bolt and separate the front speed sensor from the steering knuckle.

NOTICE:
·

Prevent foreign matter from contacting the sensor tip.

·

Be careful not to damage the front speed sensor.

·

Clean the speed sensor installation hole and the contact surfaces every time the speed sensor is removed.




Hide 4.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43512 5.REMOVE FRONT DISC

Hide 43420 7.SEPARATE FRONT DRIVE SHAFT ASSEMBLY

a.
C291620C01
2.948,0.719 2.042,0.375 2.042,0.375 2.771,0.375 true 1.854,0.281 2.021,0.458 0.167,0.177 10 true *a
*a Matchmark


Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.


b.

Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

NOTICE:

Be careful not to damage the drive shaft boot.


HINT:

If it is difficult to separate the front drive shaft assembly from the front axle assembly, tap the end of the front drive shaft assembly using a brass bar and a hammer.



Hide 48069 8.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

a.
C291619

Remove the bolt and 2 nuts, and separate the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly.


Hide 9.REMOVE FRONT AXLE ASSEMBLY

a.
C291626

Remove the 2 bolts, 2 nuts and front axle assembly from the front shock absorber assembly.

NOTICE:
·

When removing the nuts, keep the bolts from rotating.

·

Be careful not to damage the drive shaft boot or speed sensor rotor.




Hide 43246B 10.REMOVE FRONT NO. 1 WHEEL BEARING DUST DEFLECTOR

a.
C291621C01
1.927,0.896 2.781,0.896 true 2.813,0.833 3.125,0.99 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the front No. 1 wheel bearing dust deflector.

NOTICE:

Be careful not to damage the steering knuckle.



Hide 43502G 11.REMOVE FRONT AXLE HUB HOLE SNAP RING

a.
C291622

Using snap ring pliers, remove the front axle hub hole snap ring.


Hide 43502C 12.REMOVE FRONT AXLE HUB SUB-ASSEMBLY

a.
C291623N01
2.125,2.74 2.125,2.354 false 1.781,0.521 1.781,0.302 1.781,0.302 2.031,0.302 false 2.063,0.229 2.521,0.427 0.458,0.198 10 false SST 2,2.75 2.458,2.948 0.458,0.198 10 false SST

Secure the front axle assembly between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



b.

Using SST, remove the front axle hub sub-assembly.

SST
09520-00031  


c.
C167711N04
1.052,2.094 0.354,1.458 0.354,1.458 0.75,2.167 false 0.365,1.458 1.094,1.667 false 2.417,1.031 2.167,0.604 2.167,0.604 2.469,0.604 false 2.896,1.333 2.896,0.635 2.896,0.635 2.979,0.635 false 0.063,1.375 0.375,1.542 0.313,0.167 10 false SST 1.875,0.531 2.188,0.698 0.313,0.167 10 false SST 3.021,0.563 3.333,0.729 0.313,0.167 10 false SST

Using SST and a press, remove the bearing inner race (outside) from the front axle hub sub-assembly.

SST
09555-55010  
09950-60010  (09951-00440)
09950-70010  (09951-07100)

NOTICE:

Be careful not to drop the front axle hub sub-assembly.



Hide 47704 13.REMOVE FRONT DISC BRAKE DUST COVER SUB-ASSEMBLY

a.
C291624

Remove the 4 bolts and front disc brake dust cover sub-assembly from the steering knuckle.


Hide 43502E 14.REMOVE FRONT AXLE HUB BEARING

a.
C293330C01
0.854,1.833 0.625,1.583 0.625,1.583 0.938,1.583 false 1.771,3.323 1.771,2.969 false 1.958,3.333 0.917,3.333 0.917,3.333 0.917,3.219 false 2.438,0.979 2.281,0.635 2.281,0.635 2.49,0.635 false 2.625,1.844 2.625,1.292 true 0.406,3.052 0.406,2.469 true 0.333,3.052 0.646,3.208 0.313,0.156 10 false *a 1.979,3.26 2.292,3.417 0.313,0.156 10 false *b 0.344,1.51 0.802,1.708 0.458,0.198 10 false SST 2.5,1.854 2.958,2.052 0.458,0.198 10 false SST 2,0.563 2.458,0.76 0.458,0.198 10 false SST
*a Steel Plate
*b V-block


Place the bearing inner race (outside) on the front axle hub bearing.


b.

Using SST, a steel plate, V-blocks and a press, remove the front axle hub bearing from the steering knuckle.

SST
09950-60010  (09951-00440, 09952-06010)
09950-60020  (09951-00750)
09950-70010  (09951-07100)

NOTICE:

Keep the steering knuckle level.