Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FKS) › from 2016.11
RM3160E _52 Drivetrain _019686 DRIVE SHAFT / PROPELLER SHAFT _0295731 FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FKS) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FKS)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEELS

Hide 51441 2.REMOVE NO. 1 ENGINE UNDER COVER

Hide 53737B 3.REMOVE FRONT FENDER APRON SEAL LH

Hide 53736 4.REMOVE FRONT FENDER APRON SEAL RH (for AWD)

Hide 6.DRAIN TRANSFER OIL (for AWD)

Hide 43502H 7.REMOVE FRONT AXLE SHAFT NUT

a.
C292481N01
2.313,1.146 2.583,0.906 2.583,0.906 2.896,0.906 false 2.938,0.823 3.229,1.01 0.292,0.188 10 false SST

Using SST and a hammer, release the staked part of the front axle shaft nut.

SST
09930-00010  

NOTICE:

Loosen the staked part of the front axle shaft nut completely, otherwise the threads of the drive shaft may be damaged.



b.

While applying the brakes, remove the front axle shaft nut.


Hide 89543 8.SEPARATE FRONT SPEED SENSOR

a.
C291653C01
2.51,1.792 2.51,1.531 true 2.438,1.792 2.594,1.958 0.156,0.167 10 true *a
*a Sensor Clamp


Disengage the 2 claws and separate the sensor clamp.


b.

Remove the bolt and separate the front speed sensor and front flexible hose from the front shock absorber assembly.

NOTICE:

Be sure to separate the front speed sensor from the front shock absorber assembly completely.



c.
C296167

Remove the bolt and separate the front speed sensor from the steering knuckle.

NOTICE:
·

Prevent foreign matter from contacting the sensor tip.

·

Be careful not to damage the front speed sensor.

·

Clean the speed sensor installation hole and the contact surfaces every time the front speed sensor is removed.




Hide 48810 10.SEPARATE FRONT STABILIZER LINK ASSEMBLY

Hide 48069 11.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

Hide 12.SEPARATE FRONT DRIVE SHAFT ASSEMBLY

Hide 43420 13.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

a.
C292482N01
1.229,0.49 1.229,0.198 1.229,0.198 1.719,0.198 false 1.49,0.594 1.49,0.208 false 1.76,0.125 2.219,0.323 0.458,0.198 10 false SST

Using SST, remove the front drive shaft assembly LH.

SST
09520-01010  
09520-24010  (09520-32040)

NOTICE:
·

Do not damage the front drive shaft oil seal LH.

·

Do not damage the front axle inboard joint boot.

·

Do not drop the front drive shaft assembly LH.




Hide 43410 14.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for 2WD)

C367988

a.

Remove the 2 bolts and pull out the drive shaft together with the drive shaft bearing case sub-assembly.


b.

Remove the front drive shaft assembly RH from the drive shaft bearing bracket.

NOTICE:
·

Do not damage the front drive shaft oil seal RH.

·

Do not damage the front axle inboard joint boot.

·

Do not drop the front drive shaft assembly RH.



HINT:

If it is difficult to disengage the fitting, tap the end of the front drive inboard joint assembly with a brass bar and a hammer.



Hide 15.REMOVE ENGINE MOUNTING BRACKET RH (for AWD)

a.
C365236C01
1.229,0.583 1.844,0.76 true 1.24,1.75 1.958,1.531 true 1.01,1.656 1.25,1.875 0.24,0.219 10 true *a 1,0.438 1.24,0.656 0.24,0.219 10 true *b
*a Transmission Jack
*b Wooden Block


Using a transmission jack and a wooden block, support the engine assembly with transaxle at the position shown in the illustration.

NOTICE:
·

Do not position the wooden block under the oil pan.

·

Do not damage the components surrounding the engine assembly with transaxle.

·

Do not damage the front drive shaft assembly.

·

Tilt the engine assembly with transaxle as little as possible.

·

Ensure that the transmission jack and wooden block are stable.

·

Keep supporting the engine assembly with transaxle with a transmission jack until the installation of the engine mounting insulator RH has been completed.




b.
C365703

Remove the nut.


c.
C365242

Remove the 3 bolts and engine mounting bracket RH from the engine assembly.


Hide 12362 16.REMOVE ENGINE MOUNTING INSULATOR RH (for AWD)

a.

Remove the 2 hole plugs.


b.
A209885

Remove the 3 nuts and engine mounting insulator RH.


Hide 43410 17.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for AWD)

a.
C194748

Separate the bearing bracket hole snap ring from the transfer assembly.


b.

Remove the No. 1 drive shaft bearing bracket setting bolt and front drive shaft assembly RH from the transfer assembly.

NOTICE:
·

Do not damage the transfer case oil seal RH.

·

Do not damage the front axle inboard joint boot.

·

Do not drop the front drive shaft assembly RH.




c.

Remove the bearing bracket hole snap ring from the front drive shaft assembly RH.


Hide 43420G 18.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING (for LH Side)

a.
C057543

Using a screwdriver, remove the front drive shaft hole snap ring.