Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR(for 2WD) › from 2016.11
RM3160E _55 Steering _019699 STEERING GEAR / LINKAGE _0108005 STEERING GEAR(for 2WD) A

STEERING GEAR / LINKAGE  STEERING GEAR(for 2WD)  INSTALLATION  


PROCEDURE

Hide 45470 1.INSTALL TIE ROD ASSEMBLY LH

a.
C238518C04
1.24,1.042 1.24,1.563 true 1.021,1.042 1.021,1.26 1.021,1.26 1.24,1.26 true 1.156,1.573 1.313,1.719 0.156,0.146 10 *a
*a Matchmark


Install the lock nut and tie rod assembly LH to the steering gear assembly until the matchmarks are aligned.

HINT:

After adjusting the toe-in, tighten the lock nut.



Hide 45460 2.INSTALL TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 3.INSTALL STEERING LINK ASSEMBLY

a.

Install the steering link assembly to the front frame assembly with the 2 bolts and 2 nuts.

Torque:
70 N*m (714 kgf*cm, 52 ft.*lbf)

NOTICE:
·

Make sure to tighten the bolts starting from the steering link assembly pinion shaft side.

·

Keep the nut from rotating while turning the bolt because the nut has its own stopper.




Hide 48828 4.INSTALL FRONT NO. 2 STABILIZER BRACKET LH

Hide 48827 5.INSTALL FRONT NO. 2 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.


Hide 48811 6.INSTALL FRONT STABILIZER BAR

a.

Install the front stabilizer bar with 2 front No. 2 stabilizer brackets and 2 front No. 1 stabilizer bar bushings to the front frame assembly.


Hide 48829A 7.INSTALL FRONT NO. 1 STABILIZER BRACKET LH

Hide 48824A 8.INSTALL FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 9.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

a.

Install the front stabilizer link assembly LH to the front stabilizer bar with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud bolt.



Hide 48820B 10.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45470 11.CONNECT TIE ROD ASSEMBLY LH

a.
C293549

Connect the tie rod assembly LH to the steering knuckle with the nut.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:
·

Do not damage the ball joint dust cover.

·

Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.




b.

Install a new cotter pin.


Hide 45460 12.CONNECT TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45220 13.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C293548C01
1.49,2.917 1.073,2.781 1.073,2.781 1.531,2.823 true 0.865,2.677 1.042,2.854 0.177,0.177 10 true *a
*a Matchmark


Align the matchmarks on the steering intermediate shaft assembly and steering link assembly.


b.

Connect the steering intermediate shaft assembly to the steering link assembly.


c.

Install a new bolt.

Torque:
35.3 N*m (360 kgf*cm, 26 ft.*lbf)


Hide 15.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 16.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 17.INSPECT STEERING WHEEL CENTER POINT