Home › Engine / Hybrid System › 1AR-FE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2016.11
RM3160E _51 Engine / Hybrid System _019672 1AR-FE ENGINE MECHANICAL _0109594 ENGINE ASSEMBLY A

1AR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 2.REMOVE ENGINE FROM ENGINE STAND

a.

Using an engine sling device and engine lift, secure the engine assembly.

NOTICE:
·

Adjust the angle of the sling device carefully to prevent the engine assembly or engine hangers from deforming or becoming damaged.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




b.

Remove the engine assembly from the engine stand.


Hide 32101 3.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 12315A 5.INSTALL ENGINE MOUNTING BRACKET RH

a.

Install the engine mounting bracket RH with the 3 bolts.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


Hide 43457 6.INSTALL DRIVE SHAFT BEARING BRACKET

a.

Install the drive shaft bearing bracket with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12361 7.TEMPORARILY INSTALL FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


a.

Temporarily install the front engine mounting insulator with the 3 nuts.


Hide 12372A 8.TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.

Temporarily install the engine mounting insulator LH with the 3 nuts.


Hide 12362 9.TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator RH is necessary.


a.

Temporarily install the engine mounting insulator RH with the 3 nuts.


Hide 51100G 10.INSTALL FRONT FRAME ASSEMBLY

a.

Install the engine mounting insulator LH with the nut.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


b.

Install the engine mounting insulator RH with the nut.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


c.

Install the front engine mounting insulator with the bolt.

Torque:
87 N*m (887 kgf*cm, 64 ft.*lbf)


d.

Fully tighten the 9 temporarily installed nuts of the engine mounting insulators.

A172973C13
0.208,0.229 0.49,0.417 0.281,0.188 10 false *1 2.198,0.229 2.479,0.417 0.281,0.188 10 false *2 4.646,0.229 4.927,0.417 0.281,0.188 10 false *3 0.177,1.938 0.313,2.104 0.135,0.167 10 false A 0.49,1.448 0.625,1.615 0.135,0.167 10 true A 1.469,1.823 1.604,1.99 0.135,0.167 10 true A 3.021,0.958 3.156,1.125 0.135,0.167 10 false B 3.469,1.365 3.604,1.531 0.135,0.167 10 false B 3.604,0.802 3.74,0.969 0.135,0.167 10 true B 5.448,1.104 5.583,1.271 0.135,0.167 10 false B 6.01,1.094 6.146,1.26 0.135,0.167 10 false B 6.219,1.979 6.354,2.146 0.135,0.167 10 false B
*1 Front Engine Mounting Insulator *2 Engine Mounting Insulator RH
*3 Engine Mounting Insulator LH - -


HINT:

Perform this procedure only when replacement of the engine mounting insulators is necessary.


Torque:
Nut (A) : 58 N*m (591 kgf*cm, 43 ft.*lbf)
Nut (B) : 99 N*m (1010 kgf*cm, 73 ft.*lbf)


e.

Install the 5 hole plugs.

A172972C02
0.823,0.448 1.083,0.667 0.26,0.219 10 false *1 3.146,0.417 3.406,0.635 0.26,0.219 10 false *2 5.531,0.375 5.792,0.594 0.26,0.219 10 false *3
*1 Front Engine Mounting Insulator *2 Engine Mounting Insulator RH
*3 Engine Mounting Insulator LH - -


HINT:

Perform this procedure only when replacement of the engine mounting insulators is necessary.



Hide 27020 11.INSTALL GENERATOR ASSEMBLY

Hide 88310 12.INSTALL COMPRESSOR ASSEMBLY WITH PULLEY

Hide 82121 14.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine assembly with transaxle.


Hide 15.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, place the engine assembly with transaxle horizontally.

·

Do not place any height adjustment attachments or plate lift attachments under the front frame assembly.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.

·

Servicing an engine assembly while it is hanging is dangerous. This can be done only when installing/removing the engine assembly to/ from an engine stand.





c.

Install the engine assembly with transaxle to the vehicle.

NOTICE:
·

Do not raise the engine assembly with transaxle more than necessary. If the engine assembly with transaxle is raised excessively, the vehicle may also be lifted up.

·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.




d.
A315769C05
0.604,0.281 0.75,0.469 0.146,0.188 10 true B 1.458,1.063 1.594,1.25 0.135,0.188 10 true A 2.115,0.167 2.26,0.354 0.146,0.188 10 true B 1.188,0.156 1.333,0.344 0.146,0.188 10 true B 1.844,1.063 1.979,1.24 0.135,0.177 10 true A 2.667,0.323 2.813,0.51 0.146,0.188 10 true B 0.271,0.969 0.417,1.156 0.146,0.188 10 true A 2.938,0.969 3.083,1.156 0.146,0.188 10 true A 0.552,2.292 0.698,2.479 0.146,0.188 10 true C 1.479,2.375 1.625,2.552 0.146,0.177 10 true B 2.688,2.292 2.833,2.479 0.146,0.188 10 true C 1.771,2.375 1.917,2.542 0.146,0.167 10 true B 0.719,2.979 0.865,3.167 0.146,0.188 10 true D 1.115,3.229 1.26,3.417 0.146,0.188 10 true D 2.177,3.229 2.323,3.417 0.146,0.188 10 true D 2.583,2.979 2.729,3.167 0.146,0.188 10 true D
V100135

Bolt
V100136

Nut


Install the frame side rail plate RH and frame side rail plate LH with the 6 bolts and 2 nuts.

Torque:
Bolt (A) : 85 N*m (867 kgf*cm, 63 ft.*lbf)
Bolt (B) and Nut (A) : 32 N*m (326 kgf*cm, 24 ft.*lbf)


e.

Install the front suspension member rear brace RH and front suspension member rear brace LH with the 6 bolts and 2 nuts.

Torque:
Bolt (C) : 85 N*m (867 kgf*cm, 63 ft.*lbf)
Bolt (D) and Nut (B) : 32 N*m (326 kgf*cm, 24 ft.*lbf)

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 11361J 17.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover.


Hide 45220 18.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 43420G 19.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH (for LH Side)

Hide 48069 22.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

Hide 45470 23.CONNECT TIE ROD ASSEMBLY LH

Hide 45460 24.CONNECT TIE ROD ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 89543 25.INSTALL FRONT SPEED SENSOR

Hide 48810 26.INSTALL FRONT STABILIZER LINK ASSEMBLY

Hide 17410 28.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 23901 29.CONNECT FUEL TUBE SUB-ASSEMBLY

Hide 88704 30.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88703 31.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 44774 32.CONNECT UNION TO VACUUM TUBE HOSE

a.

Connect the 2 union to vacuum tube hoses to the No. 1 vacuum hose assembly and slide the 2 clips to secure them.


Hide 12363A 33.INSTALL ENGINE MOVING CONTROL ROD

HINT:

Perform this procedure only when replacement of the engine moving control rod is necessary.


a.

Temporarily install the engine moving control rod to the engine moving control rod bracket with the bolt.


Hide 12313 34.INSTALL ENGINE MOVING CONTROL ROD BRACKET

a.

When replacing the engine moving control rod sub-assembly or No. 3 engine mounting stay RH.

i.
A316583N01
0.833,0.104 0.99,0.302 0.156,0.198 10 true A 2.156,1.198 2.313,1.396 0.156,0.198 10 true B 1.646,0.49 1.802,0.688 0.156,0.198 10 true C 1.844,0.833 2,1.031 0.156,0.198 10 true D 0.646,1.344 0.802,1.542 0.156,0.198 10 true E

Install the engine moving control rod bracket with engine moving control rod sub-assembly with the 4 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)

NOTICE:

Temporarily tighten bolt (A) and bolt (B), and then fully tighten the 4 bolts in the order of bolt (C), bolt (D), bolt (A) and bolt (B).



ii.

Tighten the bolt (E).

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)



b.

When not replacing the engine moving control rod sub-assembly or No. 3 engine mounting stay RH.

i.
A314939N01
0.75,0.052 0.906,0.25 0.156,0.198 10 true A 2.135,1.188 2.292,1.385 0.156,0.198 10 true B 1.635,0.51 1.792,0.708 0.156,0.198 10 true C 1.781,0.708 1.938,0.906 0.156,0.198 10 true D

Install the engine moving control rod bracket with engine moving control rod sub-assembly with the 4 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)

NOTICE:

Temporarily tighten bolt (A) and bolt (B), and then fully tighten the 4 bolts in the order of bolt (C), bolt (D), bolt (A) and bolt (B).




Hide 12327A 35.INSTALL NO. 2 ENGINE MOUNTING STAY RH

a.

Install the No. 2 engine mounting stay RH with the 2 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 33820B 36.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C204479

Connect the transmission control cable assembly to the No. 1 control cable bracket with a new clip.


b.
C132236

Install the transmission control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17771A 37.INSTALL AIR CLEANER BRACKET

a.

Install the air cleaner bracket to the battery carrier with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 82121 38.CONNECT ENGINE WIRE

a.
A315946

Engage the 2 wire harness clamps.


b.

Push down the lock lever to connect the ECM connector.

NOTICE:
·

When connecting the ECM connector, make sure that dirt, water or other foreign matter do not contact the connecting part of the ECM connector.

·

Be sure to securely connect the ECM connectors.




c.

Connect the engine wire to the engine room relay block assembly.


d.

Connect the 4 connectors and install the engine wire to the engine room relay block assembly with the nut.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


e.

Connect the 3 wire clamps.


f.

Install the earth wire with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


g.

Install the No. 1 relay block cover to the engine room relay block assembly.


Hide 28100 39.INSTALL STARTER ASSEMBLY

Hide 32942 40.CONNECT OUTLET NO. 1 OIL COOLER HOSE

a.

Connect the outlet No. 1 oil cooler hose and slide the clip to secure it.


Hide 32941 41.CONNECT INLET NO. 1 OIL COOLER HOSE

a.

Connect the inlet No. 1 oil cooler hose and slide the clip to secure it.


Hide 87246 42.CONNECT OUTLET HEATER WATER HOSE

a.

Connect the outlet heater water hose B to the cylinder head sub-assembly and slide the clip to secure it.


b.

Engage the 2 claws to connect the inlet heater water hose and outlet heater water hose A.


Hide 87245 43.CONNECT INLET HEATER WATER HOSE

a.

Connect the inlet heater water hose to the cylinder head sub-assembly and slide the clip to secure it.


Hide 16572D 44.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet and slide the clip to secure it.


Hide 16571C 45.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose to the cylinder head sub-assembly and slide the clip to secure it.


b.

Connect the air fuel ratio sensor wire to the No. 1 radiator hose with the hose clamp.


Hide 28800 46.INSTALL BATTERY

a.

Install the battery and battery tray.


b.

Install the battery clamp with the bolt and nut.

Torque:
Bolt : 5.4 N*m (55 kgf*cm, 48 in.*lbf)
Nut : 5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.

Connect the cable to the positive (+) battery terminal.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 47233 47.INSTALL RESERVOIR BRACKET

Hide 47202 48.INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

Hide 17701 49.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.
A315810C01
2.458,0.74 3.042,0.74 true 1.792,1.052 2.375,1.052 true 1.594,0.958 1.792,1.156 0.198,0.198 10 false *a 3.125,0.667 3.323,0.865 0.198,0.198 10 false *b
*a Hole
*b Projection


Insert the projection of the air cleaner case sub-assembly into the hole of the No. 1 air cleaner bracket as shown in the illustration.


b.

Install the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 17801 50.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.

NOTICE:

Install the air cleaner filter element sub-assembly with the printed side facing the vehicle front.



Hide 17705 51.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17750A 52.INSTALL INLET AIR CLEANER ASSEMBLY

a.

Install the inlet air cleaner assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 53.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

a.

Connect the cable to the negative (-) battery terminal.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 57. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 58. WARM UP ENGINE

Hide 12601B 67.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

a.

Engage the 3 pins to install the No. 1 engine cover sub-assembly.


Hide 53295E 68.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 53298E 69.INSTALL RADIATOR SIDE SEAL RH

Hide 53299D 70.INSTALL RADIATOR SIDE DEFLECTOR SEAL LH

Hide 72.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 73.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 53737B 74.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the front fender apron seal LH with the 2 bolts and clip.


Hide 53736 75.INSTALL FRONT FENDER APRON SEAL RH

a.

Install the front fender apron seal RH with the 2 bolts and clip.


Hide 53876A 76.INSTALL FRONT FENDER LINER LH

a.

Install the front fender liner LH with the 3 screws and 3 clips.


Hide 53875A 77.INSTALL FRONT FENDER LINER RH

a.

Install the front fender liner RH with the 2 screws and 3 clips.


Hide 51454C 78.INSTALL FLOOR UNDER COVER LH

Hide 51442 79.INSTALL NO. 2 ENGINE UNDER COVER

a.

Install the No. 2 engine under cover with the 2 bolts, 2 screws and clip.


Hide 51441 80.INSTALL NO. 1 ENGINE UNDER COVER

a.

Install the No. 1 engine under cover with the 6 bolts, 8 screws and 3 clips.


Hide 81.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 82.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT