Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019701 NAVIGATION / MULTI INFO DISPLAY _0101135 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio and display receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the radio and display receiver assembly cannot be operated using the steering pad switch assembly, and the radio and display receiver assembly itself will not function.

WIRING DIAGRAM

E339382E18
0.417,1.281 1.083,1.531 0.667,0.25 10 false Volume- 1.198,1.25 1.865,1.5 0.667,0.25 10 false Volume+ 1.969,1.26 2.635,1.51 0.667,0.25 10 false Seek- 2.594,1.271 3.26,1.521 0.667,0.25 10 false Seek+ 2.167,2.375 3.25,2.719 1.083,0.344 10 false MODE/HOLD 1.01,4.844 3.115,5.083 2.104,0.24 10 false Steering Pad Switch Assembly 1.198,3.823 1.865,4.073 0.667,0.25 10 false On hook 2,3.823 2.667,4.073 0.667,0.25 10 false Off hook 2.906,3.792 3.573,4.042 0.667,0.25 10 false Voice 4.49,3.375 5.552,4.042 1.063,0.667 10 false Spiral Cable Sub-assembly 6.281,3.521 6.906,4.427 0.625,0.906 10 false Radio and Display Receiver Assembly 6.219,3.365 6.823,3.729 0.604,0.365 10 false F71 4.385,2.927 5.052,3.177 0.667,0.25 10 false z4 4.375,1.833 5.042,2.083 0.667,0.25 10 false z4 4.375,0.698 5.042,0.948 0.667,0.25 10 false z4 5.333,0.698 6,0.948 0.667,0.25 10 false F61 5.333,1.813 6,2.063 0.667,0.25 10 false F61 5.333,2.927 6,3.177 0.667,0.25 10 false F61 4.802,1.74 5.469,1.99 0.667,0.25 10 false EAU 4.813,2.854 5.479,3.104 0.667,0.25 10 false AU2 4.802,0.615 5.469,0.865 0.667,0.25 10 false AU1 6.333,0.698 7,0.948 0.667,0.25 10 false SW1 6.333,1.813 7,2.063 0.667,0.25 10 false SWG 6.344,2.938 7.01,3.188 0.667,0.25 10 false SW2 4.375,0.5 5.042,0.75 0.667,0.25 10 false 11 4.385,1.615 5.052,1.865 0.667,0.25 10 false 8 4.385,2.74 5.052,2.99 0.667,0.25 10 false 10 5.375,2.74 6.042,2.99 0.667,0.25 10 false 5 5.406,1.625 6.073,1.875 0.667,0.25 10 false 3 5.396,0.531 6.063,0.781 0.667,0.25 10 false 6 6.115,0.604 6.781,0.854 0.667,0.25 10 false 21 6.125,1.708 6.792,1.958 0.667,0.25 10 false 23 6.115,2.813 6.781,3.063 0.667,0.25 10 false 22

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)
a.

Disconnect the F71 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-21 (SW1) - F71-23 (SWG) No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 313 to 345 Ω
Volume+ switch pushed 950 to 1050 Ω
Volume- switch pushed 2955 to 3265 Ω
F71-22 (SW2) - F71-23 (SWG) No switch pushed 95 to 105 kΩ
MODE/HOLD switch pushed Below 2.5 Ω
On hook switch pushed 313 to 345 Ω
Off hook switch pushed 950 to 1050 Ω
Voice switch pushed 2955 to 3265 Ω



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY