Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019701 NAVIGATION / MULTI INFO DISPLAY _0101135 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E358481E22
1.177,0.688 2.583,1 1.406,0.313 10 false from TAIL Relay 3.76,0.844 4.375,1.042 0.615,0.198 10 false PANEL 5.521,1.979 5.833,2.177 0.313,0.198 10 false 10 5.49,2.177 5.802,2.375 0.313,0.198 10 false F69 5.573,4.969 5.885,5.167 0.313,0.198 10 false 5 5.49,5.167 5.802,5.365 0.313,0.198 10 false F70 3.688,5.052 4,5.25 0.313,0.198 10 false 20 3.688,2.177 4,2.375 0.313,0.198 10 false F61 3.688,2.75 4,2.948 0.313,0.198 10 false F61 3.771,1.979 4.083,2.177 0.313,0.198 10 false 9 3.76,2.573 4.073,2.771 0.313,0.198 10 false 4 2.677,1.979 2.99,2.177 0.313,0.198 10 false 1 2.698,2.563 3.01,2.76 0.313,0.198 10 false 9 2.656,2.167 2.969,2.365 0.313,0.198 10 false z4 2.656,2.74 2.969,2.938 0.313,0.198 10 false z4 3.135,2.083 3.542,2.271 0.406,0.188 10 false IL+2 5.875,2.177 6.281,2.365 0.406,0.188 10 false ILL+ 3.167,2.656 3.573,2.844 0.406,0.188 10 false IL-2 5.875,5.167 6.281,5.354 0.406,0.188 10 false ILL- 3.365,5.146 3.771,5.333 0.406,0.188 10 false ILL- 2.813,3.198 3.927,3.802 1.115,0.604 10 false Spiral Cable Sub-assembly 0.365,4.021 2.354,4.313 1.99,0.292 10 false Steering Pad Switch Assembly 2.667,5.667 3.042,5.865 0.375,0.198 10 false F126 2.646,5.844 4.542,6.063 1.896,0.219 10 false Combination Meter Assembly 5.677,6.01 6.979,6.479 1.302,0.469 10 false Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except radio and display receiver assembly. B
No illumination comes on (radio and display receiver assembly, hazard switch, heater control switch, etc.). C




A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the F61 spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F61-9 (IL+2) - Body ground Light control switch in tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY, COMBINATION METER ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the F69 radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F69-10 (ILL+) - Body ground Light control switch in tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F70 radio and display receiver assembly connector.


b.

Disconnect the F126 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F70-5 (ILL-) - F126-20 (ILL-) Always Below 1 Ω
F70-5 (ILL-) or F126-20 (ILL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR