Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) › from 2016.11
RM3160E _58 Vehicle Interior _019712 SEAT _0107153 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  One or more Power Seat Motors do not Operate  


DESCRIPTION

Signals are input into the position control ECU and switch assembly. The built-in ECU manages the signals received from the position control ECU and switch assembly, and operates each motor. If the position control ECU and switch assembly receives more than 2 motor operation signals, the motor is stopped. Manual operation is restarted after the position control ECU and switch assembly receives 1 signal only.

WIRING DIAGRAM

B363529E02
1.99,1.125 2.521,1.313 0.531,0.188 10 false SLD+ 1.969,0.385 2.5,0.573 0.531,0.188 10 false SYSB 2.021,1.521 2.552,1.708 0.531,0.188 10 false SLD- 1.99,2.323 2.521,2.51 0.531,0.188 10 false FRV+ 2.01,2.729 2.542,2.917 0.531,0.188 10 false FRV- 2.031,3.531 2.563,3.719 0.531,0.188 10 false LFT+ 2.052,3.927 2.583,4.115 0.531,0.188 10 false LFT- 2.521,0.406 2.833,0.573 0.313,0.167 10 false e7 0.99,4.76 2.563,5.177 1.573,0.417 10 false Position Control ECU and Switch Assembly 2.885,0.396 3.198,0.563 0.313,0.167 10 false d7 2.885,1.125 3.198,1.292 0.313,0.167 10 false d6 2.885,1.521 3.198,1.688 0.313,0.167 10 false d6 2.5,1.521 2.813,1.688 0.313,0.167 10 false e6 2.521,1.125 2.833,1.292 0.313,0.167 10 false e6 2.531,2.313 2.844,2.479 0.313,0.167 10 false e6 2.885,2.323 3.198,2.49 0.313,0.167 10 false d6 2.885,2.719 3.198,2.885 0.313,0.167 10 false d6 2.521,2.719 2.833,2.885 0.313,0.167 10 false e6 2.521,3.521 2.833,3.688 0.313,0.167 10 false e6 2.531,3.917 2.844,4.083 0.313,0.167 10 false e6 2.885,3.927 3.198,4.094 0.313,0.167 10 false d6 2.823,0.198 3.292,0.365 0.469,0.167 10 false 12*2 2.885,3.521 3.198,3.688 0.313,0.167 10 false d6 2.458,0.198 2.938,0.354 0.479,0.156 10 false 12*1 2.5,0.927 2.833,1.094 0.333,0.167 10 false 3*1 2.854,1.333 3.219,1.521 0.365,0.188 10 false 4*2 2.844,0.927 3.219,1.083 0.375,0.156 10 false 3*2 2.49,1.333 2.865,1.5 0.375,0.167 10 false 4*1 2.49,2.104 2.844,2.292 0.354,0.188 10 false 8*1 2.854,2.115 3.24,2.281 0.385,0.167 10 false 8*2 2.865,2.521 3.302,2.688 0.438,0.167 10 false 5*2 2.5,2.521 2.927,2.688 0.427,0.167 10 false 5*1 2.469,3.323 2.927,3.5 0.458,0.177 10 false 10*1 2.823,3.323 3.281,3.5 0.458,0.177 10 false 10*2 2.833,3.729 3.292,3.885 0.458,0.156 10 false 12*2 2.458,3.729 2.969,3.896 0.51,0.167 10 false 12*1 3.25,5.083 4.385,5.292 1.135,0.208 10 false *1: for LHD 3.25,5.375 4.385,5.583 1.135,0.208 10 false *2: for RHD 4.552,4.698 6.427,5.177 1.875,0.479 10 false Front Seat Adjuster Assembly (Driver Seat) 4.833,1.031 5.052,1.208 0.219,0.177 10 false 2 4.823,1.427 5.052,1.615 0.229,0.188 10 false 1 5.198,1.75 5.948,1.948 0.75,0.198 10 false e2*1, d2*2 5.188,1.906 6.146,2.167 0.958,0.26 10 false Slide Motor 4.823,2.229 5.021,2.438 0.198,0.208 10 false 2 4.969,2.938 5.802,3.104 0.833,0.167 10 false e3*1, d3*2 4.969,3.094 6.583,3.354 1.615,0.26 10 false Front Vertical Motor 4.823,2.615 5.031,2.802 0.208,0.188 10 false 1 4.833,3.427 5.01,3.615 0.177,0.188 10 false 2 5.188,4.146 6.021,4.385 0.833,0.24 10 false e4*1, d4*2 5.188,4.292 6.115,4.531 0.927,0.24 10 false Lifter Motor 3.865,0.542 5.021,0.75 1.156,0.208 10 false MPX-B NO.1 5.406,0.396 6.854,0.625 1.448,0.229 10 false from Battery 4.823,3.813 5.031,4 0.208,0.188 10 false 1

B454493E04
5.5,1.083 6.313,1.271 0.813,0.188 10 false m2*1, k2*2 5.49,1.24 6.677,1.49 1.188,0.25 10 false Reclining Motor 5.188,0.354 5.375,0.563 0.188,0.208 10 false 2 5.188,0.74 5.375,0.948 0.188,0.208 10 false 1 4.219,3.083 4.406,3.292 0.188,0.208 10 false 1 2.063,3.198 2.25,3.406 0.188,0.208 10 false 1 2.979,3.188 3.167,3.396 0.188,0.208 10 false 2 4.219,2.281 4.406,2.49 0.188,0.208 10 false 3 2.958,2.417 3.146,2.625 0.188,0.208 10 false 5 2.052,2.417 2.24,2.625 0.188,0.208 10 false 6 2.042,0.74 2.229,0.948 0.188,0.208 10 false 11 2.052,0.365 2.24,0.573 0.188,0.208 10 false 9 3.177,2.427 3.365,2.635 0.188,0.208 10 false B 3.188,3.208 3.375,3.417 0.188,0.208 10 false E 4.01,2.333 4.198,2.542 0.188,0.208 10 false H 4.021,3.104 4.208,3.313 0.188,0.208 10 false R 4.771,2.313 5.323,2.583 0.552,0.271 10 false 1*1, 2*2 4.792,3.083 5.344,3.354 0.552,0.271 10 false 2*1, 1*2 5.344,3.573 6.198,3.76 0.854,0.188 10 false m3*1, k3*2 5.344,3.74 6.885,4.115 1.542,0.375 10 false Lumbar Support Adjuster Assembly (Driver Seat) 4.99,1.604 6.74,1.958 1.75,0.354 10 false Front Seatback Frame Sub-assembly (Driver Seat) 3.115,3.781 3.896,4 0.781,0.219 10 false e8*1, d8*2 3.115,3.948 4.302,4.313 1.188,0.365 10 false Power Seat Switch Assembly 1.594,0.417 2,0.656 0.406,0.24 10 false RCL+ 1.615,0.802 2.021,1.042 0.406,0.24 10 false RCL- 1.688,2.51 2.094,2.75 0.406,0.24 10 false +B2 1.552,3.292 1.958,3.531 0.406,0.24 10 false GND2 0.594,3.823 1.323,4.042 0.729,0.219 10 false e6*1, d6*2 0.594,3.99 2.188,4.396 1.594,0.406 10 false Position Control ECU and Switch Assembly 2.115,4.406 3.021,4.656 0.906,0.25 10 false *1: for LHD 4.365,4.396 5.146,4.615 0.781,0.219 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK FRONT POWER SEAT OPERATION
a.

Check that each function of the power seat operates normally by using the position control ECU and switch assembly.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

Result:
Result Proceed to
One or more power seat functions (except lumbar support adjustment function) do not operate A
All power seat functions do not operate B
Front vertical and lifter functions do not operate C
Only lumbar support adjustment function does not operate D




A

2.READ VALUE USING GTS (POWER SEAT SWITCH)

B

GO TO OTHER DIAGNOSIS PROCEDURE (Front Power Seat does not Operate with Front Power Seat Switch)

C

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - POWER SUPPLY)

D

8.INSPECT POWER SEAT SWITCH ASSEMBLY
2.READ VALUE USING GTS (POWER SEAT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Reclining Rear Reclining switch signal (rearward) ON or OFF ON: Reclining switch (rearward) on
OFF: Reclining switch (rearward) off
-
Reclining Front Reclining switch signal (forward) ON or OFF ON: Reclining switch (forward) on
OFF: Reclining switch (forward) off
-
Front Vertical Down Front vertical switch signal (downward) ON or OFF ON: Front vertical switch (downward) on
OFF: Front vertical switch (downward) off
-
Front Vertical Up Front vertical switch signal (upward) ON or OFF ON: Front vertical switch (upward) on
OFF: Front vertical switch (upward) off
-
Lifter Switch Down Lifter switch signal (downward) ON or OFF ON: Lifter switch (downward) on
OFF: Lifter switch (downward) off
-
Lifter Switch Up Lifter switch signal (upward) ON or OFF ON: Lifter switch (upward) on
OFF: Lifter switch (upward) off
-
Slide Rear Slide switch signal (rearward) ON or OFF ON: Slide switch (rearward) on
OFF: Slide switch (rearward) off
-
Slide Front Slide switch signal (forward) ON or OFF ON: Slide switch (forward) on
OFF: Slide switch (forward) off
-
Body Electrical > Driver Seat > Data List
Tester Display
Reclining Rear
Reclining Front
Front Vertical Down
Front Vertical Up
Lifter Switch Down
Lifter Switch Up
Slide Rear
Slide Front
50003 162 17,18,19,20,21,22,23,24
OK:

ON or OFF is displayed on the GTS according to the table above.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (POWER SEAT MOTOR)

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

3.PERFORM ACTIVE TEST USING GTS (POWER SEAT MOTOR)
a.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


b.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Reclining Seat reclining operation OFF/Rear/Front -
Front Vertical Operation Seat front vertical operation OFF/Down/Up -
Lifter Operation Seat lifter operation OFF/Down/Up -
Seat Slide Operation Seat slide operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Reclining
50004 162 1
Body Electrical > Driver Seat > Active Test
Tester Display
Front Vertical Operation
50004 162 3
Body Electrical > Driver Seat > Active Test
Tester Display
Lifter Operation
50004 162 2
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Slide Operation
50004 162 4
Result:
Result Proceed to
The power seat functions operate normally A
Slide, front vertical or lifter function does not operate normally B
Reclining function does not operate normally C




A

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

B

4.INSPECT FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)

C

5.INSPECT FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)
4.INSPECT FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)
HINT:

Check the motor operation of applicable function.


a.

Remove the front seat adjuster assembly (driver seat).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY


b.

Inspect the front seat adjuster assembly (driver seat) (slide motor, front vertical motor or lifter motor).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - POWER SEAT MOTOR)

NG

REPLACE FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)

5.INSPECT FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)
a.

Remove the front seatback frame sub-assembly (driver seat).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY


b.

Inspect the front seatback frame sub-assembly (driver seat) (reclining motor).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - POWER SEAT MOTOR)

NG

REPLACE FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - POWER SEAT MOTOR)
a.

Disconnect the e6*1 or d6*2 position control ECU and switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

HINT:

Check the wire harness and connector between the position control ECU and switch assembly and applicable motor.


Standard Resistance (for LHD):
Slide Motor
Tester Connection Condition Specified Condition
e6-3 (SLD+) - e2-2 Always Below 1 Ω
e6-3 (SLD+) or e2-2 - Body ground Always 10 kΩ or higher
e6-4 (SLD-) - e2-1 Always Below 1 Ω
e6-4 (SLD-) or e2-1 - Body ground Always 10 kΩ or higher

Front Vertical Motor
Tester Connection Condition Specified Condition
e6-5 (FRV-) - e3-1 Always Below 1 Ω
e6-5 (FRV-) or e3-1- Body ground Always 10 kΩ or higher
e6-8 (FRV+) - e3-2 Always Below 1 Ω
e6-8 (FRV+) or e3-2 - Body ground Always 10 kΩ or higher

Lifter Motor
Tester Connection Condition Specified Condition
e6-10 (LFT+) - e4-2 Always Below 1 Ω
e6-10 (LFT+) or e4-2 - Body ground Always 10 kΩ or higher
e6-12 (LFT-) - e4-1 Always Below 1 Ω
e6-12 (LFT-) or e4-1 - Body ground Always 10 kΩ or higher

Reclining Motor
Tester Connection Condition Specified Condition
e6-9 (RCL+) - m2-2 Always Below 1 Ω
e6-9 (RCL+) or m2-2 - Body ground Always 10 kΩ or higher
e6-11 (RCL-) - m2-1 Always Below 1 Ω
e6-11 (RCL-) or m2-1 - Body ground Always 10 kΩ or higher


Standard Resistance (for RHD):
Slide Motor
Tester Connection Condition Specified Condition
d6-3 (SLD+) - d2-2 Always Below 1 Ω
d6-3 (SLD+) or d2-2 - Body ground Always 10 kΩ or higher
d6-4 (SLD-) - d2-1 Always Below 1 Ω
d6-4 (SLD-) or d2-1 - Body ground Always 10 kΩ or higher

Front Vertical Motor
Tester Connection Condition Specified Condition
d6-5 (FRV-) - d3-1 Always Below 1 Ω
d6-5 (FRV-) or d3-1- Body ground Always 10 kΩ or higher
d6-8 (FRV+) - d3-2 Always Below 1 Ω
d6-8 (FRV+) or d3-2 - Body ground Always 10 kΩ or higher

Lifter Motor
Tester Connection Condition Specified Condition
d6-10 (LFT+) - d4-2 Always Below 1 Ω
d6-10 (LFT+) or d4-2 - Body ground Always 10 kΩ or higher
d6-12 (LFT-) - d4-1 Always Below 1 Ω
d6-12 (LFT-) or d4-1 - Body ground Always 10 kΩ or higher

Reclining Motor
Tester Connection Condition Specified Condition
d6-9 (RCL+) - k2-2 Always Below 1 Ω
d6-9 (RCL+) or k2-2 - Body ground Always 10 kΩ or higher
d6-11 (RCL-) - k2-1 Always Below 1 Ω
d6-11 (RCL-) or k2-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - POWER SUPPLY)
a.

Disconnect the e7*1 or d7*2 position control ECU and switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
e7-12 (SYSB) - Body ground Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
d7-12 (SYSB) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT POWER SEAT SWITCH ASSEMBLY
a.

Remove the power seat switch assembly.

Click hereVehicle Interior>SEAT>LUMBAR SWITCH>REMOVAL


b.

Inspect the power seat switch assembly.

Click hereVehicle Interior>SEAT>LUMBAR SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

9.INSPECT LUMBAR SUPPORT ADJUSTER ASSEMBLY (DRIVER SEAT)

NG

REPLACE POWER SEAT SWITCH ASSEMBLY

9.INSPECT LUMBAR SUPPORT ADJUSTER ASSEMBLY (DRIVER SEAT)
a.

Remove the lumbar support adjuster assembly (driver seat).

Click hereVehicle Interior>SEAT>LUMBAR SUPPORT ADJUSTER ASSEMBLY>REMOVAL


b.

Inspect the lumbar support adjuster assembly (driver seat).

Click hereVehicle Interior>SEAT>LUMBAR SUPPORT ADJUSTER ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - POWER SEAT SWITCH ASSEMBLY)

NG

REPLACE LUMBAR SUPPORT ADJUSTER ASSEMBLY (DRIVER SEAT)

10.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - POWER SEAT SWITCH ASSEMBLY)
a.

Disconnect the e6*1 or d6*2 position control ECU and switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
e6-6 (+B2) - e8-5 (B) Always Below 1 Ω
e6-6 (+B2) or e8-5 (B) - Body ground Always 10 kΩ or higher
e6-1 (GND2) - e8-2 (E) Always Below 1 Ω
e6-1 (GND2) or e8-2 (E) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
d6-6 (+B2) - d8-5 (B) Always Below 1 Ω
d6-6 (+B2) or d8-5 (B) - Body ground Always 10 kΩ or higher
d6-1 (GND2) - d8-2 (E) Always Below 1 Ω
d6-1 (GND2) or d8-2 (E) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (POWER SEAT SWITCH ASSEMBLY - LUMBAR SUPPORT ADJUSTMENT MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (POWER SEAT SWITCH ASSEMBLY - LUMBAR SUPPORT ADJUSTMENT MOTOR)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
e8-3 (H) - m3-1 Always Below 1 Ω
e8-3 (H) or m3-1 - Body ground Always 10 kΩ or higher
e8-1 (R) - m3-2 Always Below 1 Ω
e8-1 (R) or m3-2 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
d8-3 (H) - k3-2 Always Below 1 Ω
d8-3 (H) or k3-2 - Body ground Always 10 kΩ or higher
d8-1 (R) - k3-1 Always Below 1 Ω
d8-1 (R) or k3-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR