Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HIGH BEAM SYSTEM › from 2016.11
RM3160E _59 Vehicle Exterior _019722 LIGHTING (EXT) _0103404 AUTOMATIC HIGH BEAM SYSTEM J

LIGHTING (EXT)  AUTOMATIC HIGH BEAM SYSTEM  Automatic High Beam Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects auto high beam switch signals. The automatic high beam system can be turned on and off by operating the automatic high beam switch.

WIRING DIAGRAM

E344196E04
2.281,1.104 2.438,1.302 0.156,0.198 10 false 1 3.698,1.115 3.854,1.313 0.156,0.198 10 false 4 5.313,1.115 5.521,1.365 0.208,0.25 10 false 23 5.563,1.229 6.302,1.552 0.74,0.323 10 false AHBI 5.375,2.385 5.708,2.594 0.333,0.208 10 false F18 5.365,2.563 7.01,3.146 1.646,0.583 10 false Main Body ECU (Multiplex Network Body ECU) 2.167,1.625 2.5,1.833 0.333,0.208 10 false F8 2.167,1.75 4.729,2.479 2.563,0.729 10 false Automatic High Beam Switch

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto High Beam Main Switch Automatic high beam switch signal OFF or ON OFF: Automatic high beam switch not pressed
ON: Automatic high beam switch pressed
-
Body Electrical > Main Body > Data List
Tester Display
Auto High Beam Main Switch
50003 123 274
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT AUTO HIGH BEAM SWITCH
2.INSPECT AUTO HIGH BEAM SWITCH
a.

b.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AUTO HIGH BEAM SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (AUTO HIGH BEAM SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the F18 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F8-4 - F18-23 (AHBI) Always Below 1 Ω
F8-4 or F18-23 (AHBI) - Body ground Always 10 kΩ or higher
F8-1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR