Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 6 Sensor Type) › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0297894 TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 6 Sensor Type) C

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 6 Sensor Type)  C1AE7  Rear Left Center Sensor Malfunction  


DESCRIPTION

The No. 1 ultrasonic sensor (rear left center sensor) is installed on the rear bumper. The clearance warning ECU assembly detects obstacles based on signals received from the No. 1 ultrasonic sensor (rear left center sensor). If the No. 1 ultrasonic sensor (rear left center sensor) has an open circuit or other malfunction, it will not function normally.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AE7 Rear Left Center Sensor Malfunction A malfunction of the No. 1 ultrasonic sensor (rear left center sensor)
·

No. 1 ultrasonic sensor (rear left center sensor)

·

Harness or connector

·

Clearance warning ECU assembly



WIRING DIAGRAM

E257596E49
0.688,1.677 2.542,2.125 1.854,0.448 10 false No. 1 Ultrasonic Sensor (Rear Left Center Sensor) 0.677,1.51 0.948,1.667 0.271,0.156 10 false W3 4.927,1.708 6.167,2.042 1.24,0.333 10 false Clearance Warning ECU Assembly 4.927,1.521 5.229,1.677 0.302,0.156 10 false F87 1.844,0.531 1.979,0.688 0.135,0.156 10 false S 1.844,1.167 1.979,1.323 0.135,0.156 10 false E 2.031,0.448 2.167,0.604 0.135,0.156 10 false 2 2.031,1.073 2.167,1.229 0.135,0.156 10 false 1 5.01,0.448 5.229,0.604 0.219,0.156 10 false 8 5.01,1.083 5.229,1.24 0.219,0.156 10 false 2 5.208,0.542 5.49,0.698 0.281,0.156 10 false S4 5.208,1.167 5.49,1.323 0.281,0.156 10 false E1

CAUTION / NOTICE / HINT

NOTICE:

If DTCs are output after repairs, turn the ignition switch to ON and turn the back sonar or clearance sonar switch assembly on. Then clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 6 Sensor Type)>DTC CHECK / CLEAR


PROCEDURE

1.INSPECT NO. 1 ULTRASONIC SENSOR (REAR LEFT CENTER SENSOR)
a.

Remove the No. 1 ultrasonic sensor (rear left center sensor).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear Side)>REMOVAL


b.
E257585C02
1.042,0.698 1.396,1.052 false 2.375,0.698 2.021,1.052 false 0.156,0.125 0.438,0.313 0.281,0.188 10 false *a 0.958,0.51 1.24,0.698 0.281,0.188 10 false S 2.365,0.51 2.646,0.698 0.281,0.188 10 false E
*a Component without harness connected
(No. 1 Ultrasonic Sensor (Rear Left Center Sensor))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (S) - 1 (E) Always 20 to 40 kΩ


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR (REAR LEFT CENTER SENSOR) - CLEARANCE WARNING ECU ASSEMBLY)

NG

REPLACE NO. 1 ULTRASONIC SENSOR (REAR LEFT CENTER SENSOR)

2.CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR (REAR LEFT CENTER SENSOR) - CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the F87 clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W3-2 (S) - F87-8 (S4) Always Below 1 Ω
W3-1 (E) - F87-2 (E1) Always Below 1 Ω
W3-2 (S) or F87-8 (S4) - Body ground Always 10 kΩ or higher
W3-1 (E) or F87-2 (E1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR