Home › Drivetrain › MF1A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM › from 2016.11
RM3160E _52 Drivetrain _019685 MF1A TRANSFER / 4WD / AWD _0109466 DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM D

MF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


Dynamic torque control 4WD/AWD system data can be read through the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be malfunctioning, use the GTS to check for malfunctions and perform repairs. Therefore when there seems to be a problem with the dynamic torque control 4WD/AWD system, use the GTS or SST to check and troubleshoot it.


CHECK DATA LINK CONNECTOR 3 (DLC3)




FUNCTION OF AWD WARNING


a.

If a malfunction occurs during system operation, "Check AWD System" will be displayed on the multi-information display to inform the driver of the system malfunction.

HINT:

Check that the master warning light comes on for approximately 4 seconds.




CHECK MASTER WARNING LIGHT


a.

Turn the ignition switch to ON, and check that the master warning light comes on for approximately 4 seconds.

HINT:

The master warning light goes off while the system is in DTC output mode.




CHECK AWD WARNING


a.

Check AWD warning.

i.
C166029C80
0.125,1.052 0.531,1.302 0.406,0.25 1.594,0.896 1.74,0.406 1.74,0.406 1.875,0.406 true 1.792,1.479 1.917,1.844 1.917,1.844 2.052,1.844 true 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 0.229,1.094 0.688,1.292 0.458,0.198 10 false F25 1.917,0.333 2.229,0.531 0.313,0.198 10 false CG 2.135,1.771 2.448,1.969 0.313,0.198 10 false TC
*a Front view of DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 (to enter DTC output mode).

SST
09843-18040  


ii.

Turn the ignition switch to ON.


iii.

"DIAG AWD" is displayed on the multi-information display, and the 4WD ECU assembly checks the system for malfunctions.

·

If the AWD control system is normal, "DIAG AWD FF" will be displayed on the multi-information display.

·

If the AWD control system is not normal, "DIAG AWD XX (DTC)" will be displayed on the multi-information display.

·

Although Test Mode is not set for the dynamic torque control 4WD/AWD system, a message will be displayed on the multi-information display when Test Mode is activated for checking the VSC, etc.


HINT:
·

Test mode DTCs will not be stored because test mode is not set.

·

If the systems above are not displayed on the multi-information display, there may be a malfunction in the TC and CG terminal circuit.

·

If the AWD warning check result is not normal, proceed to troubleshooting for the AWD warning circuit.


Trouble Area See Procedure
AWD warning (Remains on) (Click here)
AWD warning (Does not come on) (Click here)





CHECK AWD LOCK MODE INDICATOR LIGHT


a.

Check AWD lock mode indicator light.

i.

When the ignition switch is turned to ON, check that the AWD lock mode indicator light comes on and goes off within approximately 4 seconds.

HINT:

If the AWD lock mode indicator light do not illuminate, check for combination meter assembly and CAN communication system DTCs, since the 4WD ECU assembly and combination meter assembly are connected by the CAN communication line.

If the AWD lock mode indicator light does not come on, perform relevant troubleshooting procedures. The relevant troubleshooting procedures are in the sections listed in the table below.

Trouble Area See Procedure
AWD lock indicator light (Does not come on) (Click here)