11361J
1.REMOVE FLYWHEEL HOUSING UNDER COVER
32101A
2.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.
There will be one black colored drive plate and torque converter assembly setting bolt.
3.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
82121
4.DISCONNECT ENGINE WIRE
| *a | Transmission Wire Connector |
| *b | Park/Neutral Position Switch Assembly Connector |
Disconnect the park/neutral position switch assembly connector.
Disengage the claw, rotate the lever and disconnect the connector of the transmission wire connector.
Remove the 2 bolts and nut, and disconnect the engine wire from the automatic transaxle case sub-assembly.
35104V
5.SEPARATE BREATHER PLUG HOSE
Disengage the 3 hose clamps to separate the breather plug hose.
6.INSTALL ENGINE HANGERS
51100G
7.REMOVE FRONT FRAME ASSEMBLY
17118
8.REMOVE MANIFOLD STAY
30500
9.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY
Support the automatic transaxle assembly with a transmission jack.
Secure the automatic transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachment.
Remove the 11 bolts and automatic transaxle assembly.
To prevent damage to the knock pins, do not pry between the automatic transaxle assembly and engine assembly.
16281K
10.DISCONNECT NO. 4 WATER BY-PASS HOSE
16267H
11.DISCONNECT NO. 3 WATER BY-PASS HOSE
12.DISCONNECT INLET NO. 2 OIL COOLER HOSE
13.DISCONNECT OUTLET NO. 3 OIL COOLER HOSE
33493A
14.REMOVE TRANSMISSION OIL COOLER
32942
15.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE
32907C
16.REMOVE NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE
16570
17.REMOVE RADIATOR PIPE ASSEMBLY
| *1 | Radiator Pipe Assembly |
| *2 | No. 3 Water By-pass Hose |
| *3 | No. 4 Water By-pass Hose |
Remove the bolt and radiator pipe assembly from the automatic transaxle assembly.
Slide the clip and remove the No. 4 water by-pass hose from the radiator pipe assembly.
Slide the clip and remove the No. 3 water by-pass hose from the radiator pipe assembly.
12311A
18.REMOVE FRONT ENGINE MOUNTING BRACKET
Remove the 4 bolts and front engine mounting bracket from the automatic transaxle assembly.
12325A
19.REMOVE ENGINE MOUNTING BRACKET LH
Remove the 3 bolts and engine mounting bracket LH from the automatic transaxle case sub-assembly.
20.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Remove the 2 bolts and No. 1 transmission control cable bracket from the automatic transaxle case sub-assembly.
35150
21.REMOVE TRANSMISSION CASE PLUG ASSEMBLY
Remove the transmission case plug assembly from the automatic transaxle assembly.
22.REMOVE WIRE HARNESS CLAMP BRACKET
Remove the bolt and wire harness clamp bracket from the automatic transaxle case sub-assembly.
35104V
23.REMOVE BREATHER PLUG HOSE
Using a screwdriver, remove the breather plug hose from the No. 1 breather plug (ATM).
Be careful not to damage the No. 1 breather plug (ATM).
| *1 | Breather Plug Sub-assembly |
| *2 | Breather Plug Hose |
Remove the breather plug sub-assembly from the breather plug hose.
Be careful not to damage the breather plug sub-assembly.
32000
24.REMOVE TORQUE CONVERTER ASSEMBLY
Remove the torque converter assembly from the automatic transaxle assembly.
32000
25.INSPECT TORQUE CONVERTER ASSEMBLY
32101
26.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY