Home › Engine / Hybrid System › 2GR-FKS (INTAKE / EXHAUST) › EXHAUST MANIFOLD › from 2016.11
RM3160E _51 Engine / Hybrid System _060160 2GR-FKS INTAKE / EXHAUST _0299815 EXHAUST MANIFOLD A

2GR-FKS INTAKE / EXHAUST  EXHAUST MANIFOLD  REMOVAL  


PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51442 2.REMOVE NO. 2 ENGINE UNDER COVER

Hide 58166 3.REMOVE FRONT FLOOR COVER LH

a.
A315837C01
1.521,1.313 1.74,1.542 0.219,0.229 10 true A 1.552,0.635 1.771,0.865 0.219,0.229 10 true B 0.781,0.542 1,0.771 0.219,0.229 10 true B
V100135

Bolt
V100136

Screw


Remove the clip (A), 2 screws and 4 bolts from the front floor cover LH.


b.

Disconnect the 2 clips (B) to remove the front floor cover LH.


Hide 17403 4.REMOVE FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

a.
A395758

Disengage the 3 wire harness clamps.


b.

Disconnect the heated oxygen sensor (for Bank 1) connector.


c.
A395759C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 4 bolts, 2 nuts, 2 compression springs and front No. 3 exhaust pipe sub-assembly from the front exhaust pipe assembly and center exhaust pipe assembly (TWC: Rear Catalyst).


d.

Remove the 3 gaskets from the front No. 3 exhaust pipe sub-assembly, front exhaust pipe assembly and center exhaust pipe assembly (TWC: Rear Catalyst).


Hide 17118 5.REMOVE MANIFOLD STAY

a.
A370439C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt and nut to remove the manifold stay from the exhaust manifold (TWC: Front Catalyst) and rear engine mounting bracket.


Hide 17141 6.REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)

a.
A394870

Disconnect the air fuel ratio sensor connector.


b.

Disengage the 3 wire harness clamps.


c.
A370440

Using a 12 mm deep socket wrench, remove the 4 nuts and exhaust manifold (TWC: Front Catalyst) from the cylinder head sub-assembly RH.


Hide 17173 7.REMOVE EXHAUST MANIFOLD TO HEAD GASKET (for Bank 1)

a.
A370441

Remove the exhaust manifold to head gasket (for Bank 1) from the cylinder head sub-assembly RH.


Hide 89467B 8.REMOVE AIR FUEL RATIO SENSOR (for Bank 1)

Hide 17584B 9.REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Lower Side)

Hide 17410 10.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 11209 11.REMOVE V-BANK COVER SUB-ASSEMBLY

Hide 89467B 12.REMOVE AIR FUEL RATIO SENSOR (for Bank 2)

Hide 17168 13.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A395761

Remove the 3 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold assembly LH (TWC: Front Catalyst).


Hide 17119 14.REMOVE NO. 2 MANIFOLD STAY

a.
A395762C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt, nut and No. 2 manifold stay from the exhaust manifold assembly LH (TWC: Front Catalyst) and cylinder block sub-assembly.


Hide 17150 15.REMOVE EXHAUST MANIFOLD ASSEMBLY LH (TWC: Front Catalyst)

a.
A395763

Using a 12 mm deep socket wrench, remove the 4 nuts and exhaust manifold assembly LH (TWC: Front Catalyst).


Hide 17173 16.REMOVE EXHAUST MANIFOLD TO HEAD GASKET (for Bank 2)

a.
A395764

Remove the exhaust manifold to head gasket (for Bank 2) from the cylinder head sub-assembly.


Hide 17.REMOVE STUD BOLT

HINT:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A370453

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold (TWC: Front Catalyst).


b.
A370454

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold assembly LH (TWC: Front Catalyst).