Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2016.11
RM3160E _51 Engine / Hybrid System _060157 2GR-FKS ENGINE MECHANICAL _0299121 ENGINE ASSEMBLY A

2GR-FKS ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 2.DISCHARGE FUEL SYSTEM PRESSURE

Hide 3. PRECAUTION

CAUTION:

The engine assembly with transmission is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 5.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 7.REMOVE FRONT WHEELS

Hide 51441 8.REMOVE NO. 1 ENGINE UNDER COVER

a.

Remove the 8 bolts, 6 screws, 3 clips and No. 1 engine under cover.


Hide 51442 9.REMOVE NO. 2 ENGINE UNDER COVER

a.

Remove the 2 bolts, 2 screws, clip and No. 2 engine under cover.


Hide 53876A 11.SEPARATE FRONT FENDER LINER LH

a.

Remove the 3 screws and 3 clips and separate the front fender liner LH.


Hide 53875A 12.SEPARATE FRONT FENDER LINER RH

a.

Remove the 3 screws and 3 clips and separate the front fender liner RH.


Hide 53737B 13.REMOVE FRONT FENDER APRON SEAL LH

a.
A396411

Remove the 2 bolts, clip and front fender apron seal LH.


Hide 53736 14.REMOVE FRONT FENDER APRON SEAL RH

a.
A396412

Remove the 2 bolts, clip and front fender apron seal RH.


Hide 19.DRAIN TRANSFER OIL (for AWD)

Hide 20.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55701J 21.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 53299D 22.REMOVE RADIATOR SIDE DEFLECTOR SEAL LH

Hide 53298E 23.REMOVE RADIATOR SIDE SEAL RH

Hide 53295E 24.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 11209 25.REMOVE V-BANK COVER SUB-ASSEMBLY

a.
A392581

Hold the rear of the V-bank cover sub-assembly and raise it to disengage the 2 rear clips.


b.

Raise the V-bank cover sub-assembly to disengage the 2 front clips and remove the V-bank cover sub-assembly.

NOTICE:

Attempting to disengage both front and rear clips at the same time may cause the V-bank cover sub-assembly to break.



Hide 28800 26.REMOVE BATTERY

a.
A392582

Disconnect the cable from the positive (+) battery terminal.


b.

Remove the nut and bolt.


c.

Remove the battery clamp, battery clamp bolt, battery and battery tray.


Hide 17750A 27.REMOVE INLET AIR CLEANER ASSEMBLY

a.
A392583

Remove the 2 bolts and inlet air cleaner assembly.


Hide 17700 28.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

a.
A368598

Disconnect the mass air flow meter sub-assembly connector.


b.

Disengage the wire harness clamp.


c.
A394296C02
1.448,1.531 0.677,1.531 true 2.667,0.625 1.896,0.625 true 2.698,0.542 3.01,0.698 0.313,0.156 10 true *1 0.417,1.438 0.677,1.656 0.26,0.219 10 true *2
*1 No. 1 Fuel Vapor Feed Hose
*2 No. 2 Ventilation Hose


Disengage the No. 1 fuel vapor feed hose from the air cleaner hose assembly.


d.

Slide the clip and disconnect the No. 2 ventilation hose from the air cleaner hose assembly.


e.
A396413

Remove the 2 bolts.


f.

Loosen the hose clamp and remove the air cleaner assembly with air cleaner hose.

NOTICE:

Make sure the air cleaner support is attached to the vehicle body.



Hide 47220D 29.SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for LHD)

a.
C292889C01
0.969,3.948 0.969,3.719 true 0.448,3.938 0.448,3.729 true 0.896,3.979 1.208,4.135 0.313,0.156 10 false *1 0.385,3.969 0.698,4.125 0.313,0.156 10 false *2
*1 Brake Master Cylinder Reservoir Assembly
*2 Reservoir Bracket


Disconnect the reservoir level switch connector and remove the bolt from the brake master cylinder reservoir assembly.


b.

Move the brake master cylinder reservoir assembly as shown in the illustration to disengage the 2 claws, and separate it.


Hide 47233 30.REMOVE RESERVOIR BRACKET (for LHD)

Hide 47220D 31.SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for RHD)

a.
C294903C01
0.75,4.094 0.75,3.698 true 0.51,4.094 0.51,3.698 true 0.688,4.094 1,4.25 0.313,0.156 10 false *1 0.448,4.104 0.76,4.26 0.313,0.156 10 false *2
*1 Brake Master Cylinder Reservoir Assembly
*2 Reservoir Bracket


Disconnect the reservoir level switch connector and remove the bolt from the brake master cylinder reservoir assembly.


b.

Move the brake master cylinder reservoir assembly as shown in the illustration to disengage the 2 claws, and separate it.


Hide 47233 32.REMOVE RESERVOIR BRACKET (for RHD)

Hide 17119A 33.REMOVE AIR CLEANER BRACKET

a.
A392586

Disengage the clamp.


b.

Remove the 2 bolts and air cleaner bracket from the vehicle body.


Hide 12327A 34.REMOVE NO. 2 ENGINE MOUNTING STAY RH

a.
A397807C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt, 2 nuts and No. 2 engine mounting stay RH from the engine mounting insulator sub-assembly RH.


Hide 12313 35.REMOVE ENGINE MOVING CONTROL ROD BRACKET

a.
A392600

Remove the 4 bolts and engine moving control rod bracket with engine moving control rod from the front No. 1 engine mounting bracket LH and vehicle body.


Hide 12363A 36.REMOVE ENGINE MOVING CONTROL ROD

HINT:

Perform this procedure only when replacement of the engine moving control rod or No. 3 engine mounting stay RH is necessary.


a.
A315766

Remove the 2 bolts, engine moving control rod and No. 3 engine mounting stay RH from the engine moving control rod bracket.


Hide 23826 37.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.

Disconnect the purge VSV (purge valve) connector.


b.
A392589

Slide the clip and disconnect the No. 1 fuel vapor feed hose from the No. 1 vacuum switching valve.


Hide 44773F 38.DISCONNECT UNION TO CHECK VALVE HOSE

a.
A396414C01
0.073,0.094 0.385,0.333 0.313,0.24 12 false *A 0.042,2.427 0.354,2.667 0.313,0.24 12 false *B
*A for LHD
*B for RHD


Slide the clip and disconnect the union to check valve hose from the intake air surge tank assembly.


b.

for LHD

i.

Disengage the clamp from the union to check valve hose.



Hide 16571C 39.DISCONNECT NO. 1 RADIATOR HOSE

a.
A392590

Slide the clip and disconnect the No. 1 radiator hose from the water outlet.


b.

Separate the No. 1 radiator hose from the radiator pipe clamp.


Hide 16572D 40.DISCONNECT NO. 2 RADIATOR HOSE

a.
A392591

Slide the clip and disconnect the No. 2 radiator hose from the water inlet.


Hide 87209 41.DISCONNECT WATER HOSE SUB-ASSEMBLY

a.
A396708

Slide the 2 clips and disconnect the 2 water hose sub-assemblies.


b.

Disengage the clamp from the water hose sub-assembly.


Hide 16267H 42.DISCONNECT NO. 3 WATER BY-PASS HOSE

a.
A392597

Slide the clip and disconnect the No. 3 water by-pass hose from the radiator pipe assembly.


Hide 16281K 43.DISCONNECT NO. 4 WATER BY-PASS HOSE

a.
A392598

Slide the clip and disconnect the No. 4 water by-pass hose from the radiator pipe assembly.


Hide 23901 44.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A412601C02
0.135,0.063 0.479,0.26 0.344,0.198 12 false *A 0.198,2.458 0.521,2.708 0.323,0.25 12 false *B
*A Fuel Pipe Camp Type A
*B Fuel Pipe Camp Type B


Remove the No. 2 fuel pipe clamp from the No. 1 fuel pipe clamp.


b.
A412602C01
0.177,0.073 0.49,0.271 0.313,0.198 12 false *A 0.188,2.406 0.469,2.635 0.281,0.229 12 false *B
*A Fuel Pipe Camp Type A
*B Fuel Pipe Camp Type B


Remove the No. 1 fuel pipe clamp from the fuel tube connector.


c.

Disconnect the No. 2 fuel tube sub-assembly (for Direct Injection).

i.
A397370

Disconnect the No. 2 fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL SYSTEM>PRECAUTION



d.

Disconnect the fuel tube sub-assembly (for Port Injection).

i.
A397371

Disconnect the fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL SYSTEM>PRECAUTION



Hide 32943 45.DISCONNECT NO. 1 TRANSMISSION OIL COOLER HOSE

a.
A392593

Slide the clip and disconnect the No. 1 transmission oil cooler hose from the transmission oil thermostat.


Hide 32942 46.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE

a.
A392594

Slide the clip and disconnect the outlet No. 1 oil cooler hose from the transmission oil thermostat.


Hide 32971 47.DISCONNECT TRANSMISSION OIL THERMOSTAT

a.
A396709

Remove the bolt and disconnect the transmission oil thermostat from the oil cooler stay.


Hide 28100 48.REMOVE STARTER ASSEMBLY

Hide 82121 49.DISCONNECT ENGINE WIRE

a.
A396418

Remove the No. 1 relay block cover from the engine room relay block assembly.


b.
A392587

Remove the bolt and separate the earth wire.


c.

Remove the nut from the engine room relay block assembly.


d.

Disengage the 2 clamps to disconnect the engine wire.


e.

Disengage the 2 claws to disconnect the engine wire.


f.

Disconnect the 4 connectors from the engine room relay block assembly.


g.
A392588

Pull up the lock lever while pushing the lock on the lever to disconnect the ECM connector.

NOTICE:

After disconnecting the ECM connector, make sure that dirt, water or other foreign matter does not contact the connecting part of the ECM connector.



h.

Disengage the 2 clamps.


i.
A397367

Remove the bolt and separate the No. 3 earth wire.


j.
A396415

Disengage the clamp and disconnect the engine wire.


k.

Remove the nut and engine room main wire with engine wire from the positive (+) battery terminal.


l.
A373545

Disengage the 2 claws to disconnect the engine room main wire from the engine wire.


Hide 33820B 50.SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C366759

Remove the clip from the transmission control shaft lever as shown in the illustration.


b.

Using a screwdriver, disengage the 4 claws and disconnect the transmission control cable assembly with the clip from the No. 1 transmission control cable bracket.


c.
C227713

Using a screwdriver, disengage the 2 claws and disconnect the clip from the transmission control cable assembly.


d.
C366769

Disengage the transmission control cable assembly from the No. 3 transmission control cable bracket.


Hide 45220 51.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY (for 2WD)

Hide 45220 52.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY (for AWD)

Hide 88703 53.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 88704 54.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 37100 55.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for AWD)

Hide 17403 56.REMOVE FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

Hide 17410 57.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 17571 58.REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET

a.
A392566

Remove the 2 nuts and No. 1 exhaust pipe support bracket from the oil pan sub-assembly.


Hide 89542 62.SEPARATE FRONT SPEED SENSOR RH

HINT:

Use the same procedure as for the LH side.


Hide 45460 64.SEPARATE TIE ROD ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 48810 65.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 66.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 48069 67.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 68.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 69.SEPARATE FRONT DRIVE SHAFT ASSEMBLY

Hide 43410 71.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for 2WD)

Hide 43420G 72.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING (for LH Side)

Hide 11361J 73.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
A396416

Remove the 2 bolts and flywheel housing under cover.


Hide 32101A 74.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT (for 2WD)

Hide 32101A 75.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT (for AWD)

Hide 76.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Place height adjustment attachments and plate lift attachments, set an engine lifter underneath the engine assembly with transaxle.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.




b.
A392602C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 6 bolts, 2 nuts, frame side rail plate RH and frame side rail plate LH from the front frame assembly and vehicle body.


c.

Remove the 6 bolts, 2 nuts, front suspension member rear brace RH and front suspension member rear brace LH from the front frame assembly and vehicle body.


d.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle body.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




Hide 77.INSTALL ENGINE HANGERS

a.
A373557C02
1.104,0.729 1.521,0.729 true 2.688,0.719 3.115,0.719 true 0.021,0.021 0.354,0.271 0.333,0.25 12 true *A 1.677,0.031 2,0.26 0.323,0.229 12 true *B 1.583,0.646 1.896,0.802 0.313,0.156 10 false *1 3.156,0.646 3.406,0.865 0.25,0.219 10 false *2
*A for Bank 1
*B for Bank 2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-31121
No. 2 Engine Hanger 12282-31100
Bolt 91671-10825



b.

Using an engine sling device and engine lifter, secure the engine assembly with transaxle.

NOTICE:
·

Adjust the angle of the sling device carefully to prevent damage or deformation to the engine hangers or engine assembly.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




Hide 82121 78.REMOVE ENGINE WIRE

a.

Disconnect all clamps and connectors and remove the engine wire from the engine assembly with transaxle.


Hide 48829A 79.REMOVE FRONT NO. 1 STABILIZER BRACKET LH (for AWD)

Hide 48824A 80.REMOVE FRONT NO. 1 STABILIZER BRACKET RH (for AWD)

HINT:

Perform the same procedure as for the LH side.


Hide 51100G 83.REMOVE FRONT FRAME ASSEMBLY

a.
A392603

Remove the bolt and disconnect the front engine mounting insulator assembly.


b.
A392604

Remove the nut and disconnect the engine mounting insulator LH.


c.
A392605

Remove the nut and disconnect the engine mounting insulator RH.


d.
A392606C01
0.083,0.146 0.458,0.385 0.375,0.24 12 false *A 0.104,2.458 0.479,2.698 0.375,0.24 12 false *B
*A for 2WD
*B for AWD


Remove the 2 bolts and disconnect the rear engine mounting insulator assembly.


e.

Remove the front frame assembly.


Hide 43410 84.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for AWD)

Hide 12315A 87.REMOVE ENGINE MOUNTING BRACKET RH

a.
A392607

Remove the 3 bolts and engine mounting bracket RH from the cylinder block sub-assembly.


Hide 32101 88.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 89.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine assembly to an engine stand.


Hide 90.REMOVE ENGINE HANGERS

a.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and cylinder head LH.


Hide 12360 91.REMOVE FRONT ENGINE MOUNTING INSULATOR ASSEMBLY

HINT:

Perform this procedure only when replacement of the front engine mounting insulator assembly is necessary.


a.
A373560

Remove the hole plug from the front frame assembly.


b.
A373561

Remove the 3 nuts and front engine mounting insulator assembly.


Hide 12372A 92.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A315940

Remove the 2 hole plugs from the front frame assembly.


b.
A392609

Remove the 3 nuts and engine mounting insulator LH.


Hide 12362 93.REMOVE ENGINE MOUNTING INSULATOR RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator RH is necessary.


a.
A315941

Remove the 2 hole plugs from the front frame assembly.


b.
A392610

Remove the 3 nuts and engine mounting insulator RH.


Hide 12380 94.REMOVE REAR ENGINE MOUNTING INSULATOR ASSEMBLY

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator assembly is necessary.


a.
A171843

Remove the 2 hole plugs from the front frame assembly.


b.
A392611C01
0.115,0.188 0.427,0.458 0.313,0.271 12 false *A 0.146,2.604 0.458,2.802 0.313,0.198 12 false *B
*A for 2WD
*B for AWD


Remove the 2 nuts and rear engine mounting insulator assembly.