Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019701 NAVIGATION / MULTI INFO DISPLAY _0101135 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

·

w/o Manual (SOS) Switch:

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio and display receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.

·

w/ Manual (SOS) Switch:

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the telematics transceiver sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly via the telematics transceiver.


WIRING DIAGRAM

E268440E56
0.094,0.083 2.083,0.333 1.99,0.25 12 false w/o Manual (SOS) Switch: 0.083,4.417 2.958,4.646 2.875,0.229 12 false w/ Manual (SOS) Switch: 0.823,0.802 1.323,0.969 0.5,0.167 10 false MACC 0.823,1.271 1.323,1.438 0.5,0.167 10 false MCO+ 0.854,1.75 1.354,1.917 0.5,0.167 10 false MCO- 0.865,5.104 1.365,5.271 0.5,0.167 10 false SNS2 0.854,2.698 1.354,2.865 0.5,0.167 10 false SNS2 0.813,5.583 1.313,5.75 0.5,0.167 10 false MACC 0.823,6.052 1.323,6.219 0.5,0.167 10 false MCO+ 0.854,6.531 1.354,6.698 0.5,0.167 10 false MCO- 0.167,3.156 0.5,3.323 0.333,0.167 10 false S1 0.167,3.323 2.146,3.74 1.979,0.417 10 false Map Light Assembly (Telephone Microphone Assembly) 0.167,7.385 0.5,7.552 0.333,0.167 10 false S1 0.167,7.552 2.146,7.969 1.979,0.417 10 false Map Light Assembly (Telephone Microphone Assembly) 2.01,6.865 2.677,7.031 0.667,0.167 10 false (Shielded) 3.25,2.083 3.917,2.25 0.667,0.167 10 false (Shielded) 1.333,0.708 1.5,0.875 0.167,0.167 10 false 3 1.333,1.188 1.5,1.354 0.167,0.167 10 false 2 1.333,1.667 1.5,1.833 0.167,0.167 10 false 4 1.333,2.615 1.823,2.885 0.49,0.271 10 false 13 1.344,6.448 1.51,6.615 0.167,0.167 10 false 4 1.344,5.969 1.51,6.135 0.167,0.167 10 false 2 1.344,5.5 1.51,5.667 0.167,0.167 10 false 3 1.344,5 1.677,5.24 0.333,0.24 10 false 13 3.24,5.479 3.49,5.646 0.25,0.167 10 false 33 3.24,5.948 3.49,6.115 0.25,0.167 10 false 34 3.24,6.427 3.49,6.594 0.25,0.167 10 false 35 3.24,6.885 3.49,7.052 0.25,0.167 10 false 32 3.417,7.385 3.833,7.552 0.417,0.167 10 false F140 3.417,7.552 5.115,7.917 1.698,0.365 10 false Telematics Transceiver 5.438,7.385 5.75,7.573 0.313,0.188 10 false F71 5.427,7.563 7.125,8.073 1.698,0.51 10 false Radio and Display Receiver Assembly 5.667,2.135 5.917,2.302 0.25,0.167 10 false 18 4.448,6.448 4.698,6.615 0.25,0.167 10 false 19 5.667,6.448 5.917,6.615 0.25,0.167 10 false 19 5.667,6.917 5.917,7.083 0.25,0.167 10 false 18 5.74,5.021 5.906,5.188 0.167,0.167 10 false 6 5.74,5.969 5.906,6.135 0.167,0.167 10 false 5 5.938,5.094 6.438,5.26 0.5,0.167 10 false SNS2 5.938,6.083 6.417,6.25 0.479,0.167 10 false MIN+ 5.938,6.5 6.417,6.667 0.479,0.167 10 false MIN- 5.938,7 6.417,7.167 0.479,0.167 10 false SGND 4.781,6.865 5.448,7.031 0.667,0.167 10 false (Shielded) 3.51,5.583 4.01,5.75 0.5,0.167 10 false MCVD 3.51,6.052 3.927,6.219 0.417,0.167 10 false MCI+ 3.51,6.542 3.927,6.708 0.417,0.167 10 false MCI- 3.51,7.01 4.01,7.177 0.5,0.167 10 false SGND 3.948,6.052 4.365,6.219 0.417,0.167 10 false MCO+ 3.979,6.542 4.396,6.708 0.417,0.167 10 false MCO- 5.74,0.708 5.906,0.875 0.167,0.167 10 false 4 5.74,1.188 5.906,1.354 0.167,0.167 10 false 5 5.74,2.615 5.906,2.781 0.167,0.167 10 false 6 5.667,1.667 5.917,1.833 0.25,0.167 10 false 19 5.938,0.781 6.438,0.948 0.5,0.167 10 false MACC 5.938,1.26 6.417,1.427 0.479,0.167 10 false MIN+ 5.938,1.75 6.417,1.917 0.479,0.167 10 false MIN- 5.938,2.229 6.417,2.396 0.479,0.167 10 false SGND 5.938,2.708 6.417,2.875 0.479,0.167 10 false SNS2 5.417,3.104 5.802,3.302 0.385,0.198 10 false F71 5.417,3.292 7.135,3.823 1.719,0.531 10 false Radio and Display Receiver Assembly 4.448,5.969 4.698,6.135 0.25,0.167 10 false 18

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>PRECAUTION


PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E277821

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Result Proceed to
NG (w/o Manual (SOS) Switch) A
NG (w/ Manual (SOS) Switch) B
OK C



A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

B

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

C

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F71 radio and display receiver assembly connector.


b.

Disconnect the S1 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-6 (SNS2) - S1-13 (SNS2) Always Below 1 Ω
F71-4 (MACC) - S1-3 (MACC) Always Below 1 Ω
F71-5 (MIN+) - S1-2 (MCO+) Always Below 1 Ω
F71-19 (MIN-) - S1-4 (MCO-) Always Below 1 Ω
F71-6 (SNS2) or S1-13 (SNS2) - Body ground Always 10 kΩ or higher
F71-4 (MACC) or S1-3 (MACC) - Body ground Always 10 kΩ or higher
F71-5 (MIN+) or S1-2 (MCO+) - Body ground Always 10 kΩ or higher
F71-19 (MIN-) or S1-4 (MCO-) - Body ground Always 10 kΩ or higher
F71-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the F71 radio and display receiver assembly connector.


b.

Reconnect the S1 map light assembly (telephone microphone assembly) connector.


c.
E176671C63
1.479,0.542 1.969,0.833 0.49,0.292 2.229,2.01 2.896,2.698 false 2.229,1.74 2.854,1.302 false 2.052,2.01 1.385,2.698 false 1.604,0.594 2.188,0.979 0.583,0.385 10 false F71 0.24,0.177 0.615,0.542 0.375,0.365 10 false *a 2.75,2.708 3.26,3 0.51,0.292 10 false SGND 2.875,1.198 3.427,1.594 0.552,0.396 10 false MACC 1.167,2.708 1.688,2.979 0.521,0.271 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F71-4 (MACC) - Body ground Engine switch on (ACC) 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-18 (SGND) - Body ground Always Below 1 Ω
F71-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E287094C01
2.656,1.781 2.208,1.417 false 2.406,0.656 1.99,1.198 false 0.188,0.146 0.5,0.302 0.313,0.156 10 false *a 2.708,1.698 3.24,1.948 0.531,0.25 10 false SNS2 2.5,0.563 3.031,0.813 0.531,0.25 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (SNS2) - 4 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Reconnect the F71 radio and display receiver assembly connector.


b.

Reconnect the S1 map light assembly (telephone microphone assembly) connector.


c.

Turn the engine switch on (ACC).


d.
E287103C01
1.583,0.167 1.885,0.365 0.302,0.198 2.083,1.177 2.667,0.75 false 1.896,1.271 2.333,1.833 false 0.167,0.167 0.333,0.333 0.167,0.167 10 false *a 1.646,0.167 1.896,0.333 0.25,0.167 10 false S1 2.667,0.563 3.167,0.729 0.5,0.167 10 false MCO+ 2.333,1.844 2.833,2.01 0.5,0.167 10 false MCO-
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 2 (MCO+) and 4 (MCO-) of the S1 map light assembly (telephone microphone assembly) connector.


e.

Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. B




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F71 radio and display receiver assembly connector.


b.

Disconnect the S1 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-6 (SNS2) - S1-13 (SNS2) Always Below 1 Ω
F71-6 (SNS2) or S1-13 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the F71 radio and display receiver assembly connector.


b.

Disconnect the F140 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-5 (MIN+) - F140-18 (MCO+) Always Below 1 Ω
F71-19 (MIN-) - F140-19 (MCO-) Always Below 1 Ω
F71-5 (MIN+) or F140-18 (MCO+) - Body ground Always 10 kΩ or higher
F71-19 (MIN-) or F140-19 (MCO-) - Body ground Always 10 kΩ or higher
F71-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F140 telematics transceiver connector.


b.

Disconnect the S1 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F140-33 (MCVD) - S1-3 (MACC) Always Below 1 Ω
F140-34 (MCI+) - S1-2 (MCO+) Always Below 1 Ω
F140-35 (MCI-) - S1-4 (MCO-) Always Below 1 Ω
F140-33 (MCVD) or S1-3 (MACC) - Body ground Always 10 kΩ or higher
F140-34 (MCI+) or S1-2 (MCO+) - Body ground Always 10 kΩ or higher
F140-35 (MCI-) or S1-4 (MCO-) - Body ground Always 10 kΩ or higher
F140-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Disconnect the F140 telematics transceiver connector.


b.
E176671C64
1.479,0.542 1.969,0.833 0.49,0.292 2.229,2.01 2.896,2.698 false 2.052,2.01 1.385,2.698 false 1.604,0.594 1.927,0.854 0.323,0.26 10 false F71 0.24,0.177 0.615,0.542 0.375,0.365 10 false *a 2.75,2.708 3.26,3 0.51,0.292 10 false SGND 1.167,2.708 1.688,2.979 0.521,0.271 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Reconnect the F71 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-18 (SGND) - Body ground Always Below 1 Ω
F71-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.INSPECT TELEMATICS TRANSCEIVER

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

10.INSPECT TELEMATICS TRANSCEIVER
a.

Reconnect the F140 telematics transceiver connector.


b.
E259127C57
1.469,0.531 1.906,0.802 0.438,0.271 0.583,2.75 1.188,2.125 false 1.083,2.75 1.385,2.125 false 2.083,2.75 1.49,2.125 false 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 1.531,0.573 1.865,0.771 0.333,0.198 10 false F140 0.333,2.781 0.75,2.948 0.417,0.167 10 false MCI- 0.833,2.781 1.333,2.948 0.5,0.167 10 false MCVD 2,2.781 2.5,2.948 0.5,0.167 10 false SGND
*a Component with harness connected
(Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F140-33 (MCVD) - Body ground Engine switch on (ACC) 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F140-35 (MCI-) - Body ground Always Below 1 Ω
F140-32 (SGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

11.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E287094C01
2.656,1.781 2.208,1.417 false 2.406,0.656 1.99,1.198 false 0.188,0.146 0.5,0.302 0.313,0.156 10 false *a 2.708,1.698 3.24,1.948 0.531,0.25 10 false SNS2 2.5,0.563 3.031,0.813 0.531,0.25 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (SNS2) - 4 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

12.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Reconnect the F71 radio and display receiver assembly connector.


b.

Reconnect the S1 map light assembly (telephone microphone assembly) connector.


c.

Reconnect the F140 telematics transceiver connector.


d.

Turn the engine switch on (ACC).


e.
E287103C01
1.583,0.167 1.885,0.365 0.302,0.198 2.083,1.177 2.667,0.75 false 1.896,1.271 2.333,1.833 false 0.167,0.167 0.333,0.333 0.167,0.167 10 false *a 1.646,0.167 1.896,0.333 0.25,0.167 10 false S1 2.667,0.563 3.167,0.729 0.5,0.167 10 false MCO+ 2.333,1.844 2.833,2.01 0.5,0.167 10 false MCO-
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 2 (MCO+) and 4 (MCO-) of the S1 map light assembly (telephone microphone assembly) connector.


f.

Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. B




A

B

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)