Home › Engine / Hybrid System › 2GR-FKS FUEL › FUEL SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _060158 2GR-FKS FUEL _0298776 FUEL SYSTEM L

2GR-FKS FUEL  FUEL SYSTEM  PRECAUTION  


IGNITION SWITCH EXPRESSIONS


a.

The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression Ignition Switch (Position) Engine Switch (Condition)
Ignition Switch off LOCK Off (Lock)
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START On (Start)



BEFORE WORKING ON FUEL SYSTEM


a.

Before inspecting and repairing the fuel system, disconnect the cable from the negative (-) battery terminal.

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



b.

Do not smoke or work near fire when handling the fuel system.


c.

Keep fuel away from rubber or leather parts.



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Make sure the engine coolant temperature is 60°C (140°F) or less when performing this procedure.

·

Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

·

Pressure will still remain in the fuel lines even after performing the following procedure. When disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.



a.

When discharging fuel system pressure by disconnecting the FUEL PMP relay:

i.

Remove the No. 1 engine room relay block and No. 1 junction block assembly cover.


ii.

Remove the FUEL PMP relay.


iii.
A393277

Disconnect the No. 6 engine wire connector and No. 7 engine wire connector.


iv.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop on its own.



v.

Crank the engine again and make sure that the engine does not start.

HINT:

DTC P008700 (Fuel Rail / System Pressure - Too Low), P017100/P017400 (System Too Lean), P160300 (Engine Stall History), P160400 (Startability Malfunction) or P160500 (Rough Idling) may be stored. Clear the DTCs before proceeding to the next step.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR



vi.

Remove the fuel tank cap assembly and discharge the pressure from the fuel tank assembly.


vii.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



viii.

Connect the No. 6 engine wire connector and No. 7 engine wire connector.


ix.

Install the FUEL PMP relay.


x.

Install the No. 1 engine room relay block and No. 1 junction block assembly cover.



b.

When discharging fuel system pressure by disconnecting the fuel pump connector:

i.

Disconnect the fuel pump connector.

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL PUMP>REMOVAL


ii.
A393277

Disconnect the No. 6 engine wire connector and No. 7 engine wire connector.


iii.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop on its own.



iv.

Crank the engine again and make sure that the engine does not start.

HINT:

DTC P008700 (Fuel Rail / System Pressure - Too Low), P017100/P017400 (System Too Lean), P160300 (Engine Stall History), P160400 (Startability Malfunction) or P160500 (Rough Idling) may be stored. Clear the DTCs before proceeding to the next step.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR



v.

Remove the fuel tank cap assembly and discharge the pressure from the fuel tank assembly.


vi.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



vii.

Connect the No. 6 engine wire connector and No. 7 engine wire connector.


viii.

Connect the fuel pump connector.

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL PUMP>INSTALLATION




FUEL LINE


a.

When disconnecting a high-pressure fuel line, a large amount of fuel will spray. Perform the following procedure:

i.

Discharge fuel system pressure.


ii.

Disconnect the fuel tube.


iii.

Drain the fuel remaining inside the fuel pump tube into a container.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



b.

Quick Type A:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A412601C01
0.135,0.063 0.479,0.26 0.344,0.198 12 false *A 0.198,2.458 0.521,2.708 0.323,0.25 12 false *B
*A Fuel Pipe Camp Type A
*B Fuel Pipe Camp Type B


Disengage the 2 claws to remove the No. 2 fuel pipe clamp.


ii.
A412602C01
0.177,0.073 0.49,0.271 0.313,0.198 12 false *A 0.188,2.406 0.469,2.635 0.281,0.229 12 false *B
*A Fuel Pipe Camp Type A
*B Fuel Pipe Camp Type B


Remove the No. 1 fuel pipe clamp from the fuel tube connector.


iii.

Check that there is no foreign matter around the fuel tube connector before disconnecting it. Clean it if necessary.


iv.
A393280C01
1.177,2.219 1.417,2.219 false 1.99,3.177 2.125,2.979 2.125,2.979 2.24,2.979 false 0.635,3.292 0.76,3.292 0.76,3.292 0.906,3.542 false 2.135,3.896 2.323,4.271 2.323,4.271 2.448,4.271 false 1.896,4.073 1.896,4.281 false 1.292,4.167 1.604,4.167 1.604,4.167 1.604,3.906 false 1.49,4.156 1.49,3.906 false 1.01,2.125 1.323,2.281 0.313,0.156 10 false *a 1.125,4.083 1.438,4.24 0.313,0.156 10 false *b 1.823,4.281 2.135,4.438 0.313,0.156 10 false *c 0.479,3.208 0.792,3.365 0.313,0.156 10 false *d 2.49,4.188 2.802,4.344 0.313,0.156 10 false *e 2.281,2.896 2.594,3.052 0.313,0.156 10 false *a
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Nylon Tube
*e Fuel Pipe
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the fuel tube connector.


v.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




vi.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


vii.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



c.

Quick Type A:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A393281C01
1.167,2.354 1.448,2.354 false 1,2.25 1.313,2.406 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe and push them together. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


ii.

Connect the fuel lines and push in the retainer. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.


iii.

Install the No. 1 fuel pipe clamp to the fuel tube connector.


iv.

Fuel Pipe Clamp Type A:

Engage the 2 claws to install the No. 2 fuel pipe clamp.


v.
A412603C01
0.833,2.042 1.354,2.042 1.354,2.042 1.354,1.854 false 1.125,2.042 1.125,1.771 false 2.646,1.792 2.052,1.792 2.052,1.792 2.052,1.438 true 2.26,1.792 2.26,1.583 true 0.667,1.948 0.979,2.104 0.313,0.156 10 false *a 2.677,1.708 2.99,1.865 0.313,0.156 10 false *b
*a Protrusion
*b Notch


Fuel Pipe Clamp Type B:

Align the protrusions of the No. 2 fuel pipe clamp with the notches of the No. 1 fuel pipe clamp, and engage the 2 claws to install the No. 2 fuel pipe clamp.




d.

Quick Type B:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A318103C02
0.698,2.625 0.854,2.625 0.854,2.625 1.042,3.135 false 0.24,3.021 0.375,3.021 0.375,3.021 0.51,3.333 false 0.99,4.021 0.99,3.75 false 2.146,1.844 2.417,1.844 false 1.865,3.906 1.865,3.583 false 2.771,3.177 2.823,2.865 2.823,2.865 2.938,2.865 false 1.688,3.594 1.688,3.906 1.688,3.906 2.208,3.906 false 2.146,1.573 2.417,1.573 false 2.865,1.563 3.135,1.563 false 1.969,1.76 2.281,1.917 0.313,0.156 10 false *a 0.063,2.948 0.375,3.104 0.313,0.156 10 false *b 3,2.792 3.313,2.948 0.313,0.156 10 false *c 0.906,4.052 1.219,4.208 0.313,0.156 10 false *d 2.25,3.833 2.563,3.99 0.313,0.156 10 false *e 0.521,2.542 0.833,2.698 0.313,0.156 10 false *a 3.198,1.5 3.375,1.677 0.177,0.177 10 false *f 2,1.5 2.177,1.677 0.177,0.177 10 false *f
*a Retainer
*b Fuel Pipe
*c Nylon Tube
*d Fuel Tube Connector
*e O-ring
*f Claw
V100135

Push
V100136

Pull out
V100137

Pull off


Disengage the 2 claws of the retainer. Pull out the retainer and disconnect the fuel tube connector from the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



e.

Quick Type B:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A303816C02
1.958,1.531 2.365,1.531 false 1.958,1.281 2.365,1.281 false 2.781,1.271 3.188,1.271 false 1.781,1.448 2.094,1.604 0.313,0.156 10 false *a 1.823,1.198 2.135,1.354 0.313,0.156 10 false *b 3.24,1.208 3.427,1.365 0.188,0.156 10 false *b
*a Retainer
*b Claw
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


ii.

Connect the fuel lines and push in the retainer to engage the 2 claws. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




f.

Quick Type C:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A363273C01
1.958,2.177 1.75,2.177 false 2.042,2.677 1.823,2.885 1.823,2.885 1.698,2.885 true 1.979,3.677 1.979,3.271 1.979,3.271 1.719,3.271 false 2.844,2.854 2.708,2.854 2.708,2.854 2.521,2.667 true 2.719,3.208 2.552,3.208 2.552,3.208 2.375,3.521 false 2.865,4.375 2.729,4.375 2.729,4.375 2.615,4.021 false 2.031,4.135 2.031,4.375 false 1.573,2.073 1.885,2.229 0.313,0.156 10 false *a 2.917,4.302 3.229,4.458 0.313,0.156 10 false *b 1.958,4.385 2.271,4.542 0.313,0.156 10 false *c 1.552,3.188 1.865,3.344 0.313,0.156 10 false *d 1.531,2.792 1.844,2.948 0.313,0.156 10 false *e 2.771,3.125 3.083,3.281 0.313,0.156 10 false *a 2.896,2.771 3.208,2.927 0.313,0.156 10 false *e
*a Retainer
*b Fuel Pipe
*c Fuel Tube Connector
*d O-ring
*e Claw
V100135

Pull
V100136

Pull out
V100137

Pull off


Disengage the 2 claws of the retainer. Pull out the retainer and disconnect the fuel tube connector from the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has an O-ring that seals the pipe (fuel pipe).




iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



g.

Quick Type C:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A366419C01
2.271,3 2.365,3 2.365,3 2.469,2.885 true 2.198,2.406 2.427,2.406 false 2.979,2.885 3.125,3 3.125,3 3.188,3 true 2.031,2.313 2.344,2.469 0.313,0.156 10 false *a 2.094,2.917 2.406,3.073 0.313,0.156 10 false *b 3.229,2.917 3.427,3.094 0.198,0.177 10 false *b
*a Retainer
*b Claw
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


ii.

Connect the fuel lines and push in the retainer to engage the 2 claws. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




h.
A289951C03
2.333,0.427 2.521,0.427 2.521,0.427 2.823,0.74 false 0.917,1.615 1.104,1.615 1.104,1.615 1.365,1.333 false 1.708,1.281 1.906,1.594 1.906,1.594 2.052,1.594 false 2.156,0.354 2.448,0.594 0.292,0.24 10 *a 2.115,1.531 2.438,1.792 0.323,0.26 10 *b 0.698,1.563 1,1.823 0.302,0.26 10 *c
*a Fuel Tube Connector
*b Nylon Tube
*c Ethylene Propylene Diene Monomer (EPDM) Rubber Protector


Observe the following precautions when handling a nylon tube:

NOTICE:
·

Do not twist the nylon tube of the fuel tube connector or fuel tube connector when connecting it.

·

Do not remove the Ethylene Propylene Diene Monomer (EPDM) rubber protector on the outside of the nylon tube.

·

Do not bend, twist, pinch or kink the nylon tube.





FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


NOTICE:
·
A368838C01
1.865,0.813 2.292,0.813 true 2.344,0.729 2.656,0.885 0.313,0.156 10 false *a
*a Tube


Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is pressed into the fuel suction plate sub-assembly.

·

When replacing the fuel filter, replace it together with the fuel suction plate sub-assembly.




INSPECT FOR FUEL LEAK


a.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs.

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION