Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Clearance Warning ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Clearance Warning ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Clearance Warning (Clearance Sonar)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Clearance Warning ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Clearance warning ECU assembly branch line or connector

·

Power source circuit of clearance warning ECU assembly

·

Clearance warning ECU assembly ground circuit

·

Clearance warning ECU assembly



WIRING DIAGRAM

C363483E10
0.125,1.844 0.583,2.042 0.458,0.198 10 false F103 5.521,4.052 7.042,4.5 1.521,0.448 10 false Clearance Warning ECU Assembly 5.24,4.052 5.698,4.25 0.458,0.198 10 false F87 5.281,0.75 5.74,0.948 0.458,0.198 10 false 17 5.281,1.344 5.74,1.542 0.458,0.198 10 false 18 5.615,0.865 6.073,1.063 0.458,0.198 10 false R1 1.656,1.344 2.115,1.542 0.458,0.198 10 false 19 1.698,0.75 2.156,0.948 0.458,0.198 10 false 9 5.615,1.458 6.073,1.656 0.458,0.198 10 false R2 5.615,2.469 6.073,2.667 0.458,0.198 10 false IG 5.615,3.063 6.073,3.26 0.458,0.198 10 false E 0.5,1.844 2.74,2.135 2.24,0.292 10 false No. 4 CAN Junction Connector 5.302,2.958 5.76,3.156 0.458,0.198 10 false 27 5.302,2.354 5.76,2.552 0.458,0.198 10 false 12 3.844,2.302 4.979,2.552 1.135,0.25 10 false IG1 NO. 3 1.635,2.458 3.396,2.885 1.76,0.427 10 false from IG1 NO. 3 Relay 0.104,0.073 1.573,0.313 1.469,0.24 12 false for LHD:

C363483E11
0.125,1.844 0.583,2.042 0.458,0.198 10 false F102 5.521,4.052 7.042,4.5 1.521,0.448 10 false Clearance Warning ECU Assembly 5.24,4.052 5.698,4.25 0.458,0.198 10 false F87 5.281,0.75 5.74,0.948 0.458,0.198 10 false 17 5.281,1.344 5.74,1.542 0.458,0.198 10 false 18 5.615,0.865 6.073,1.063 0.458,0.198 10 false R1 1.656,1.344 2.115,1.542 0.458,0.198 10 false 15 1.698,0.75 2.156,0.948 0.458,0.198 10 false 5 5.615,1.458 6.073,1.656 0.458,0.198 10 false R2 5.615,2.469 6.073,2.667 0.458,0.198 10 false IG 5.615,3.063 6.073,3.26 0.458,0.198 10 false E 0.5,1.844 2.74,2.135 2.24,0.292 10 false No. 3 CAN Junction Connector 5.302,2.958 5.76,3.156 0.458,0.198 10 false 27 5.302,2.354 5.76,2.552 0.458,0.198 10 false 12 3.844,2.302 4.979,2.552 1.135,0.25 10 false IG1 NO. 3 1.635,2.458 3.396,2.885 1.76,0.427 10 false from IG1 NO. 3 Relay 0.104,0.073 1.573,0.313 1.469,0.24 12 false for RHD:

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait at least 14 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (CLEARANCE WARNING ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C292375C01
1.51,0.208 1.917,0.49 0.406,0.281 2.948,0.979 2.823,0.167 2.823,0.167 2.729,0.167 true 2.813,1 2.573,0.396 2.573,0.396 2.479,0.396 true 0.052,0.052 0.365,0.25 0.313,0.198 10 false *a 1.594,0.25 2.052,0.448 0.458,0.198 10 false F87 2.521,0.073 2.833,0.271 0.313,0.198 10 false R2 2.271,0.302 2.583,0.5 0.313,0.198 10 false R1
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Disconnect the F87 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F87-17 (R1) - F87-18 (R2) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C292375C02
1.51,0.208 1.917,0.49 0.406,0.281 1.948,1.854 1.823,1.854 1.823,1.854 1.458,1.156 true 0.052,0.052 0.365,0.25 0.313,0.198 10 false *a 1.594,0.25 2.052,0.448 0.458,0.198 10 false F87 2.01,1.75 2.323,1.948 0.313,0.198 10 false E
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F87-27 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C292375C03
1.51,0.208 1.917,0.49 0.406,0.281 2.292,0.99 2.594,0.396 2.594,0.396 2.688,0.396 true 0.052,0.052 0.365,0.25 0.313,0.198 10 false *a 1.594,0.25 2.052,0.448 0.458,0.198 10 false F87 2.75,0.302 3.063,0.5 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F87-12 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)