Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Combination Meter" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Combination meter assembly main line or connector

·

Power source circuit of combination meter assembly

·

Combination meter assembly ground circuit

·

Combination meter assembly



WIRING DIAGRAM

C306931E21
5.656,0.885 6.135,1.042 0.479,0.156 10 false CANH 5.677,1.677 6.156,1.833 0.479,0.156 10 false CANL 5.646,3.135 6.125,3.292 0.479,0.156 10 false IG+ 5.646,2.375 6.125,2.531 0.479,0.156 10 false B 5.656,3.979 6.135,4.135 0.479,0.156 10 false ES 5.375,0.885 5.698,1.083 0.323,0.198 10 false 28 5.375,1.406 5.656,1.604 0.281,0.198 10 false 27 5.406,2.25 5.719,2.438 0.313,0.188 10 false 1 5.375,3.021 5.688,3.302 0.313,0.281 10 false 21 5.375,3.854 5.781,4.052 0.406,0.198 10 false 31 1.531,0.885 1.688,1.083 0.156,0.198 10 false 8 1.5,1.396 1.781,1.594 0.281,0.198 10 false 18 0.188,1.917 0.698,2.208 0.51,0.292 10 false F103 0.552,1.917 2.677,2.271 2.125,0.354 10 false No. 4 CAN Junction Connector 4.104,2.958 5.25,3.135 1.146,0.177 10 false METER 3.938,2.198 5.083,2.427 1.146,0.229 10 false MPX-B NO. 1 2.281,2.354 3.802,2.813 1.521,0.458 10 false from Battery 2.146,3.125 3.906,3.542 1.76,0.417 10 false from IG2 Relay 4.844,4.854 5.427,5.135 0.583,0.281 10 false F126 5.198,4.854 7.083,5.083 1.885,0.229 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait at least 52 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY MAIN LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C301172C78
0.677,0.385 1.146,0.656 0.469,0.271 1.427,1.625 1.594,1.99 1.594,1.99 1.802,1.99 true 1.313,1.625 1.156,1.99 1.156,1.99 0.917,1.99 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 0.771,0.438 1.229,0.719 0.458,0.281 10 false F126 0.51,1.906 1.135,2.083 0.625,0.177 10 false CANL 1.865,1.917 2.479,2.115 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the F126 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F126-28 (CANH) - F126-27 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (COMBINATION METER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C301172C79
0.677,0.385 1.146,0.646 0.469,0.26 1.781,1.615 1.979,2.021 1.979,2.021 2.063,2.021 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 0.76,0.438 1.24,0.74 0.479,0.302 10 false F126 2.167,1.948 2.479,2.146 0.313,0.198 10 false ES
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F126-31 (ES) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.
C301172C80
0.677,0.385 1.167,0.646 0.49,0.26 0.615,1.438 0.406,0.99 0.406,0.99 0.281,0.99 true 0.615,1.604 0.438,1.823 0.438,1.823 0.354,1.823 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 0.76,0.438 1.219,0.656 0.458,0.219 10 false F126 0.156,0.906 0.313,1.083 0.156,0.177 10 false B 0.063,1.74 0.521,1.938 0.458,0.198 10 false IG+
*a Front view of wire harness connector
(to Combination Meter Assembly)


Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F126-1 (B) - Body ground Always 11 to 14 V
F126-21 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)