Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Driving Support ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Driving Support ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Driving Support (Cruise Control-ACC)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Driving Support ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Driving support ECU assembly branch line or connector

·

Power source circuit of driving support ECU assembly

·

Driving support ECU assembly ground circuit

·

Driving support ECU assembly



WIRING DIAGRAM

C367476E02
5.052,3.792 7.094,4.073 2.042,0.281 10 false Driving Support ECU Assembly 4.667,3.792 5.281,3.99 0.615,0.198 10 false F128 5.646,2.802 6.104,3 0.458,0.198 10 false GND 5.656,1.99 5.813,2.188 0.156,0.198 10 false B 5.646,0.677 6.26,0.875 0.615,0.198 10 false CA2H 5.646,1.198 6.26,1.396 0.615,0.198 10 false CA2L 5.438,1.885 5.75,2.083 0.313,0.198 10 false 7 5.385,2.677 5.698,2.875 0.313,0.198 10 false 28 5.375,0.552 5.688,0.75 0.313,0.198 10 false 10 5.385,1.073 5.698,1.271 0.313,0.198 10 false 11 0.448,1.594 2.542,1.854 2.094,0.26 10 false No. 1 CAN Junction Connector 1.542,0.573 1.698,0.771 0.156,0.198 10 false 1 1.552,1.104 1.708,1.302 0.156,0.198 10 false 2 4.031,1.823 4.833,2.063 0.802,0.24 10 false IG1 NO. 3 1.75,1.969 3.177,2.24 1.427,0.271 10 false from IG1 NO. 3 Relay 0.073,1.594 0.688,1.792 0.615,0.198 10 false F110

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait at least 11 seconds. Turn the cruise control main switch on and then drive the vehicle at a speed of 36 km/h (22 mph) or more for 4 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (DRIVING SUPPORT ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C346990C32
1.51,0.406 1.958,0.646 0.448,0.24 2.448,0.896 2.615,0.896 2.615,0.896 2.615,1.792 true 2.927,0.896 2.771,0.896 2.771,0.896 2.771,1.792 true 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a 1.594,0.448 2.177,0.802 0.583,0.354 10 false F128 2.052,0.833 2.51,0.99 0.458,0.156 10 false CA2H 2.969,0.833 3.427,0.99 0.458,0.156 10 false CA2L
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the F128 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F128-10 (CA2H) - F128-11 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C346990C34
1.51,0.406 1.958,0.646 0.448,0.24 1.052,0.906 1.219,0.906 1.219,0.906 1.219,1.802 true 2.646,2.75 2.479,2.75 2.479,2.75 2.479,2.094 true 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a 1.583,0.448 2.281,0.76 0.698,0.313 10 false F128 0.917,0.854 1.135,1.01 0.219,0.156 10 false B 2.698,2.688 3.156,2.844 0.458,0.156 10 false GND
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F128-28 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F128-7 (B) - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)