Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in Bus 3 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the CAN main bus lines when the resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

CAN main bus lines or connector

·

Central gateway ECU (network gateway ECU)

·

No. 7 CAN junction connector



This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

C355721E12
0.771,4.458 2.729,5.094 1.958,0.635 10 false Central Gateway ECU (Network Gateway ECU) 1.573,1 2.188,1.198 0.615,0.198 10 false CA3H 1.604,1.469 2.219,1.667 0.615,0.198 10 false CA3L 1.552,3.438 2.167,3.635 0.615,0.198 10 false CAYH 1.573,3.906 2.188,4.104 0.615,0.198 10 false CAYL 0.979,1.344 1.75,1.542 0.771,0.198 10 false 120 Ω 0.969,3.781 1.74,3.979 0.771,0.198 10 false 120 Ω 2.073,1 2.385,1.198 0.313,0.198 10 false 6 2.063,1.469 2.375,1.667 0.313,0.198 10 false 21 2.052,3.438 2.313,3.656 0.26,0.219 10 false 19 2.063,3.906 2.375,4.104 0.313,0.198 10 false 20 5.323,0.979 5.635,1.177 0.313,0.198 10 false 1 5.271,1.448 5.583,1.646 0.313,0.198 10 false 12 5.313,3.417 5.625,3.615 0.313,0.198 10 false 2 5.26,3.896 5.573,4.094 0.313,0.198 10 false 13 5.469,4.427 6.719,4.979 1.25,0.552 10 false No. 7 CAN Junction Connector 0.396,4.458 0.854,4.656 0.458,0.198 10 false F127 5.052,4.427 5.51,4.625 0.458,0.198 10 false F135

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait at least 31 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F135 No. 7 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C292404C55
3.177,0.302 3.625,0.563 0.448,0.26 2.729,1.698 2.188,0.885 2.188,0.885 2.042,0.885 true 2.844,1.698 2.375,0.552 2.375,0.552 2.24,0.552 true 2.188,2.365 2.417,2.365 2.417,2.365 2.844,1.917 true 1.99,2.135 2.24,2.135 2.24,2.135 2.719,1.906 true 0.063,0.031 0.375,0.229 0.313,0.198 10 false *a 3.24,0.354 3.771,0.604 0.531,0.25 10 false F135 1.479,0.813 2.396,1.01 0.917,0.198 10 false CANH*b 1.458,2.063 2.375,2.26 0.917,0.198 10 false CANL*b 1.635,0.479 2.552,0.677 0.917,0.198 10 false CANH*b 1.604,2.323 2.521,2.521 0.917,0.198 10 false CANL*b
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F135-1 (CANH) - F135-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
F135-2 (CANH) - F135-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)



Result:
Result
OK
NG



OK

REPLACE NO. 7 CAN JUNCTION CONNECTOR

NG

2.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 7 CAN JUNCTION CONNECTOR)
2.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 7 CAN JUNCTION CONNECTOR)
a.

Reconnect the F135 No. 7 CAN junction connector.


b.
C365513C08
1.531,0.104 1.979,0.354 0.448,0.25 2.281,0.938 2.281,0.219 2.281,0.219 2.448,0.219 true 1.75,2.01 2.052,2.01 2.052,2.01 2.052,1.198 true 1.458,1.802 1.906,1.802 1.906,1.802 1.906,1.198 true 2.469,1.802 2.177,1.802 2.177,1.802 2.177,1.198 true 1.604,0.146 2.167,0.552 0.563,0.406 10 false F127 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 2.542,0.135 3.156,0.333 0.615,0.198 10 false CA3H 2.563,1.719 3.177,1.917 0.615,0.198 10 false CA3L 1,1.719 1.427,1.938 0.427,0.219 10 false CAYH 1.333,1.938 1.771,2.125 0.438,0.188 10 false CAYL
*a Front view of wire harness connector
(to Central gateway ECU (network gateway ECU))


Disconnect the F127 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F127-6 (CA3H) - F127-19 (CAYH) Cable disconnected from negative (-) battery terminal Below 1 Ω
F127-21 (CA3L) - F127-20 (CAYL) Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 7 CAN JUNCTION CONNECTOR)