Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in Bus 5 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the CAN main bus lines when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

CAN main bus lines or connector

·

Central gateway ECU (network gateway ECU)

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector

·

CAN junction terminal



This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

C367643E02
0.25,2.125 1.021,2.323 0.771,0.198 10 false 120 Ω 6.604,2.125 7.052,2.344 0.448,0.219 10 false 120 Ω 0.833,1.76 1.604,1.958 0.771,0.198 10 false CA5H 0.854,2.302 1.625,2.5 0.771,0.198 10 false CA5L 5.99,1.76 6.76,1.958 0.771,0.198 10 false CANH 5.99,2.302 6.76,2.5 0.771,0.198 10 false CANL 2.01,1.875 2.781,2.073 0.771,0.198 10 false F105 2.01,2.406 2.781,2.604 0.771,0.198 10 false F105 3.115,2.406 3.885,2.604 0.771,0.198 10 false F104 3.115,1.875 3.885,2.073 0.771,0.198 10 false F104 3.948,2.396 4.719,2.594 0.771,0.198 10 false M38 5.042,1.875 5.813,2.073 0.771,0.198 10 false M41 3.948,1.875 4.719,2.073 0.771,0.198 10 false M38 5.063,2.406 5.833,2.604 0.771,0.198 10 false M41 1.344,1.75 1.615,1.979 0.271,0.229 10 false 15 1.344,2.292 1.615,2.521 0.271,0.229 10 false 16 2.104,1.667 2.375,1.896 0.271,0.229 10 false 1 2.125,2.198 2.396,2.427 0.271,0.229 10 false 2 3.229,2.208 3.5,2.438 0.271,0.229 10 false 2 4.052,2.208 4.323,2.438 0.271,0.229 10 false 2 5.135,2.208 5.406,2.438 0.271,0.229 10 false 2 3.219,1.677 3.49,1.906 0.271,0.229 10 false 1 4.031,1.677 4.302,1.906 0.271,0.229 10 false 1 5.135,1.667 5.406,1.896 0.271,0.229 10 false 1 5.781,2.292 6.052,2.521 0.271,0.229 10 false 2 5.76,1.75 6.031,1.979 0.271,0.229 10 false 3 2.104,2.833 3.354,3.229 1.25,0.396 10 false No. 1 CAN Junction Connector 4.021,2.844 5.271,3.24 1.25,0.396 10 false No. 2 CAN Junction Connector 6.063,2.854 6.917,3.25 0.854,0.396 10 false CAN Junction Terminal 5.719,2.854 6.167,3.073 0.448,0.219 10 false M42 0.052,2.854 0.5,3.073 0.448,0.219 10 false F127 0.427,2.854 1.813,3.458 1.385,0.604 10 false Central Gateway ECU (Network Gateway ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds. Turn the cruise control main switch on and then drive the vehicle at a speed of 36 km/h (22 mph) or more for 9 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F127 central gateway ECU (network gateway ECU) connector.


c.
C364670C12
1.479,0.156 1.948,0.417 0.469,0.26 1.094,1.792 1.385,1.792 1.385,1.792 1.385,1.188 true 1.813,1.781 1.51,1.781 1.51,1.781 1.51,1.177 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.552,0.198 2.094,0.469 0.542,0.271 10 false F127 0.677,1.719 1.292,1.917 0.615,0.198 10 false CA5H 1.854,1.698 2.469,1.896 0.615,0.198 10 false CA5L
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F127-15 (CA5H) - F127-16 (CA5L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

2.CHECK FOR OPEN IN CAN MAIN BUS LINES (CAN JUNCTION TERMINAL)
2.CHECK FOR OPEN IN CAN MAIN BUS LINES (CAN JUNCTION TERMINAL)
a.

Reconnect the F127 central gateway ECU (network gateway ECU) connector.


b.

Disconnect the M42 CAN junction terminal connector.


c.
C285690C84
1.49,0.219 1.958,0.531 0.469,0.313 1.208,1.802 1.354,1.802 1.354,1.802 1.781,1.24 true 2.51,1.781 2.385,1.781 2.385,1.781 2.052,1.26 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.573,0.292 2.188,0.49 0.615,0.198 10 false M42 0.833,1.719 1.448,1.917 0.615,0.198 10 false CANL 2.573,1.698 3.188,1.896 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to CAN Junction Terminal)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M42-3 (CANH) - M42-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN JUNCTION TERMINAL

NG

3.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
3.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the M42 CAN junction terminal connector.


b.

Disconnect the F104 and F105 wire harness connectors.


c.
C368447C01
0.729,1.479 1.208,1.74 0.479,0.26 1.76,1.49 2.24,1.75 0.479,0.26 0.49,2.146 0.656,2.146 0.656,2.146 0.771,2.354 true 1.115,3.292 0.938,3.292 0.938,3.292 0.865,2.438 true 2.115,2.854 1.969,2.854 1.969,2.854 1.885,2.438 true 1.448,2.521 1.615,2.521 1.615,2.521 1.771,2.365 true 1.313,1.906 1.135,1.906 1.135,1.906 0.99,2.24 true 1.177,2.958 1.052,2.958 1.052,2.958 0.979,2.417 true 2.458,2.125 2.229,2.125 2.229,2.125 2.021,2.26 true 2.438,2.521 2.25,2.521 2.25,2.521 2.01,2.406 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 0.813,1.521 1.427,1.719 0.615,0.198 10 false F104 1.854,1.531 2.469,1.729 0.615,0.198 10 false F105 1.375,1.833 2.292,2.031 0.917,0.198 10 false CANH*b 1.208,2.875 2.125,3.073 0.917,0.198 10 false CANL*b 2.51,2.052 3.135,2.26 0.625,0.208 10 false CANH*c 2.49,2.448 3.104,2.667 0.615,0.219 10 false CANL*c 0.271,2.063 0.583,2.26 0.313,0.198 10 false BR 1.323,2.427 1.635,2.625 0.313,0.198 10 false L 2.177,2.781 2.333,2.979 0.156,0.198 10 false W 1.167,3.198 1.323,3.396 0.156,0.198 10 false W
*a Rear view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F104-1 (CANH) - F104-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN junction connector
F105-1 (CANH) - F105-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)

Wiring Color:
Code Color (CANH Side) Color (CANL Side) Connected to
F104 BR W No. 2 CAN junction connector
F105 L W Central gateway ECU (network gateway ECU)



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



Result:
Result Proceed to
OK A
NG (Central gateway ECU (network gateway ECU) main line) B
NG (No. 2 CAN junction connector main line) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

4.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
4.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Reconnect the F104 and F105 wire harness connectors.


b.

Disconnect the M38 and M41 wire harness connectors.


c.
C368448C01
0.406,1.646 0.781,1.896 0.375,0.25 1.417,1.656 1.792,1.906 0.375,0.25 1.927,3.135 1.719,3.135 1.719,3.135 1.5,2.552 true 1.635,2.385 1.969,2.188 1.969,2.188 2.167,2.188 true 1.635,2.531 1.938,2.771 1.938,2.771 2.156,2.771 true 1.104,2.667 1.24,2.667 1.24,2.667 1.406,2.49 true 0.594,2.542 0.656,2.979 0.656,2.979 0.771,2.979 true 0.885,3.24 0.604,3.24 0.604,3.24 0.479,2.552 true 0.594,2.375 0.771,2.01 0.771,2.01 0.917,2.01 true 0.385,2.469 0.385,1.938 0.385,1.938 0.25,1.938 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 0.458,1.698 0.917,1.896 0.458,0.198 10 false M38 1.479,1.708 1.938,1.906 0.458,0.198 10 false M41 0.969,1.938 1.885,2.135 0.917,0.198 10 false CANH*b 0.813,2.896 1.729,3.094 0.917,0.198 10 false CANL*b 2.219,2.115 2.823,2.344 0.604,0.229 10 false CANH*c 2.219,2.708 2.844,2.917 0.625,0.208 10 false CANL*c 0.99,2.583 1.146,2.781 0.156,0.198 10 false B 1.969,3.052 2.167,3.26 0.198,0.208 10 false W 0.938,3.156 1.135,3.365 0.198,0.208 10 false W 0.042,1.865 0.354,2.063 0.313,0.198 10 false BR
*a Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 1 CAN Junction Connector
*c to CAN Junction Terminal


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
M38-1 (CANH) - M38-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 1 CAN junction connector
M41-1 (CANH) - M41-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN junction terminal

Wiring Color:
Code Color (CANH Side) Color (CANL Side) Connected to
M38 BR W No. 1 CAN junction connector
M41 B W CAN junction terminal



NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.



Result:
Result Proceed to
OK A
NG (No. 1 CAN junction connector main line) B
NG (CAN junction terminal main line) C



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - CAN JUNCTION TERMINAL)