There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
| Symptom | Trouble Area |
|---|---|
| No resistance exists between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3. | ·
Short to +B in CAN main bus line ·
Short to +B in CAN branch line ·
Central gateway ECU (network gateway ECU) ·
Driving support ECU assembly (w/ Toyota Safety Sense) ·
Millimeter wave radar sensor assembly (w/ Toyota Safety Sense) ·
Forward recognition camera (w/ Toyota Safety Sense) ·
Parking assist ECU (w/ Panoramic View Monitor System) ·
Television camera assembly (w/ Parking Assist Monitor System) ·
Blind spot monitor sensor LH (w/ Blind Spot Monitor System) ·
No. 1 CAN junction connector ·
No. 2 CAN junction connector ·
CAN junction terminal |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds. Turn the cruise control main switch on and then drive the vehicle at a speed of 36 km/h (22 mph) or more for 9 seconds or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Disconnect the cable from the negative (-) battery terminal.
| *1 | DLC3 |
| *a | Rear view of wire harness connector
(to No. 2 CAN Junction Connector) |
| *b | to CAN Junction Terminal |
Disconnect the M41 wire harness connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M41-1 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M41-2 (CANL) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
Before disconnecting the connectors, make a note of where they are connected.
Reconnect each connector to its original position.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the M41 wire harness connector.
| *1 | DLC3 |
| *a | Component with harness connected
(No. 2 CAN Junction Connector) |
| *b | to CAN Junction Terminal |
Connect the probes of an electrical tester to terminals 1 (CANH) and 2 (CANL) of the M41 wire harness connector and BAT of the DLC3.
While observing the resistance value shown on the electrical tester, disconnect the F105, F108, F110, F133, F134, M39 and M40 connectors from the No. 1 CAN junction connector and No. 2 CAN junction connector until the resistance becomes normal (6 kΩ or higher (for +B short)).
| *A | w/ Toyota Safety Sense | *B | w/ Panoramic View Monitor System |
| *C | w/ Blind Spot Monitor System | *D | w/ Parking Assist Monitor System |
| *1 | Central Gateway ECU (Network Gateway ECU) | *2 | Forward Recognition Camera |
| *3 | Driving Support ECU Assembly | *4 | Millimeter Wave Radar Sensor Assembly |
| *5 | Parking Assist ECU | *6 | CAN Junction Terminal |
| *7 | Blind Spot Monitor Sensor LH | *8 | Television Camera Assembly |
| *9 | No. 1 CAN Junction Connector | *10 | No. 2 CAN Junction Connector |
| *a | Component without harness connected
(No. 1 CAN Junction Connector) |
- | - |
| No. 1 CAN Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
|---|---|---|---|
| No. 2 CAN junction connector | F104 | BR | W |
| Central gateway ECU (network gateway ECU) | F105 | L | W |
| Forward recognition camera*1 | F108 | R | W |
| Driving support ECU assembly*1 | F110 | G | W |
| Millimeter wave radar sensor assembly*1 | F133 | P | W |
| Parking assist ECU*2 | F134 | LG | W |
*1: w/ Toyota Safety Sense
*2: w/ Panoramic View Monitor System
| *a | Component without harness connected
(No. 2 CAN Junction Connector) |
- | - |
| No. 2 CAN Junction Connector Side | Code | Color (CANH Side) | Color (CANL Side) |
|---|---|---|---|
| No. 1 CAN junction connector | M38 | BR | W |
| Television camera assembly*1 | M39 | B | W |
| Blind spot monitor sensor LH*2 | M40 | GR | W |
| CAN junction terminal | M41 | B | W |
*1: w/ Parking Assist Monitor System
*2: w/ Blind Spot Monitor System
| Result | Proceed to |
|---|---|
| The resistance between terminals CANH and BAT, or the resistance between terminals CANL and BAT is still below 6 kΩ when all the specified connectors are disconnected from the CAN junction connector.
(There is a short to +B in the CAN main bus lines between the No. 1 CAN junction connector and No. 2 CAN junction connector.) |
A |
| The resistance between terminals CANH and BAT, or the resistance between terminals CANL and BAT becomes normal (6 kΩ or higher) when a connector is disconnected from the CAN junction connector.
(There is a short to +B in one of the areas that relate to one or more of the disconnected bus lines.) |
B |
A
B
Reconnect all wire harness connectors.
Disconnect the M38 wire harness connector.
| *1 | DLC3 |
| *a | Component with harness connected
(No. 2 CAN Junction Connector) |
| *b | to CAN Junction Terminal |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M41-1 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M41-2 (CANL) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
Before disconnecting the connectors, make a note of where they are connected.
Reconnect each connector to its original position.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the M38 wire harness connector.
Disconnect the F104 wire harness connector.
| *1 | DLC3 |
| *a | Component with harness connected
(No. 2 CAN Junction Connector) |
| *b | to CAN Junction Terminal |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M41-1 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M41-2 (CANL) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
Before disconnecting the connectors, make a note of where they are connected.
Reconnect each connector to its original position.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
| *1 | DLC3 |
| *a | Component with harness connected
(No. 2 CAN Junction Connector) |
| *b | to CAN Junction Terminal |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M41-1 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M41-2 (CANL) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the M41 wire harness connector.
Disconnect the M42 CAN junction terminal connector.
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to CAN Junction Terminal) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M42-3 (CANH) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| M42-2 (CANL) - F25-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG