Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.11–2018.09
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Turn the ignition switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.

·

Turn the ignition switch off before inspecting CAN bus lines for a ground short.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



NO. 1 CAN JUNCTION CONNECTOR


a.

Check the No. 1 CAN junction connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


i.

Connection diagram

C368348C01
4.396,1.917 4.115,1.917 4.115,1.917 3.938,1.323 true 3.938,1.167 4.115,0.615 4.115,0.615 4.365,0.615 true 4.198,2.208 3.917,2.208 3.917,2.208 3.615,1.323 true 3.615,1.156 3.854,0.417 3.854,0.417 4.104,0.417 true 3.281,1.156 3.583,0.188 3.583,0.188 3.833,0.188 true 3.927,2.438 3.646,2.438 3.646,2.438 3.281,1.313 true 2.948,1.156 2.667,0.198 2.667,0.198 2.375,0.198 true 2.948,1.333 2.635,2.438 2.635,2.438 2.333,2.438 true 2.625,1.313 2.333,2.177 2.333,2.177 2.031,2.177 true 2.302,1.323 1.927,1.896 1.927,1.896 1.625,1.896 true 2.625,1.156 2.417,0.438 2.417,0.438 2.125,0.438 true 2.302,1.156 2.125,0.646 2.125,0.646 1.635,0.646 true 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 1.073,0.573 1.99,0.771 0.917,0.198 10 false CANH*b 1.094,1.802 2.01,2 0.917,0.198 10 false CANL*b 1.479,2.083 2.396,2.281 0.917,0.198 10 false CANL*c 1.802,2.354 2.719,2.552 0.917,0.198 10 false CANL*d 3.99,2.365 4.906,2.563 0.917,0.198 10 false CANL*e 4.26,2.135 5.177,2.333 0.917,0.198 10 false CANL*f 4.448,1.844 5.365,2.042 0.917,0.198 10 false CANL*g 1.583,0.344 2.5,0.542 0.917,0.198 10 false CANH*c 1.823,0.115 2.74,0.313 0.917,0.198 10 false CANH*d 3.885,0.115 4.802,0.313 0.917,0.198 10 false CANH*e 4.156,0.344 5.073,0.542 0.917,0.198 10 false CANH*f 4.438,0.552 5.354,0.75 0.917,0.198 10 false CANH*g
*a Component with harness connected
(No. 1 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
(for Bus 5)
*c to Central Gateway ECU (Network Gateway ECU)
(for Bus 5)
*d to Forward Recognition Camera
(w/ Toyota Safety Sense)
(for Bus 5)
*e to Driving Support ECU Assembly
(w/ Toyota Safety Sense)
(for Bus 5)
*f to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
(for Bus 5)
*g to Parking Assist ECU
(w/ Panoramic View Monitor System)
(for Bus 5)
- -



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F104-1 (CANH) BR No. 2 CAN junction connector
(for Bus 5)
F104-2 (CANL) W
F105-1 (CANH) L Central gateway ECU (network gateway ECU)
(for Bus 5)
F105-2 (CANL) W
F108-1 (CANH) R Forward recognition camera*1
(for Bus 5)
F108-2 (CANL) W
F110-1 (CANH) G Driving support ECU assembly*1
(for Bus 5)
F110-2 (CANL) W
F133-1 (CANH) P Millimeter wave radar sensor assembly*1
(for Bus 5)
F133-2 (CANL) W
F134-1 (CANH) LG Parking assist ECU*2
(for Bus 5)
F134-2 (CANL) W

·

*1: w/ Toyota Safety Sense

·

*2: w/ Panoramic View Monitor System





NO. 2 CAN JUNCTION CONNECTOR


a.

Check the No. 2 CAN junction connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


i.

Connection diagram

C295152C04
2.625,1.208 2.635,0.813 2.635,0.813 1.5,0.813 true 2.625,1.333 2.625,2.063 2.625,2.063 1.5,2.063 true 2.896,1.198 2.906,0.552 2.906,0.552 2.01,0.552 true 3.177,1.188 3.177,0.292 3.177,0.292 4.521,0.292 true 2.906,1.323 2.906,2.417 2.906,2.417 2.063,2.417 true 3.448,1.198 3.448,0.667 3.448,0.667 4.969,0.667 true 3.177,1.333 3.177,2.427 3.177,2.427 4.552,2.427 true 3.448,1.323 3.448,2.135 3.448,2.135 4.969,2.135 true 0.042,0.042 0.354,0.24 0.313,0.198 10 false *a 0.927,0.719 1.844,0.917 0.917,0.198 10 false CANH*b 0.938,1.979 1.854,2.177 0.917,0.198 10 false CANL*b 1.427,0.469 2.344,0.667 0.917,0.198 10 false CANH*c 1.5,2.323 2.417,2.521 0.917,0.198 10 false CANL*c 4.594,0.208 5.51,0.406 0.917,0.198 10 false CANH*d 4.656,2.344 5.573,2.542 0.917,0.198 10 false CANL*d 5.042,2.042 5.958,2.24 0.917,0.198 10 false CANL*e 5.063,0.573 5.979,0.771 0.917,0.198 10 false CANH*e
*a Component with harness connected
(No. 2 CAN Junction Connector)
*b to No. 1 CAN Junction Connector
(for Bus 5)
*c to CAN Junction Terminal
(for Bus 5)
*d to Blind Spot Monitor Sensor LH
(w/ Blind Spot Monitor System)
(for Bus 5)
*e to Television Camera Assembly
(w/ Parking Assist Monitor System)
(for Bus 5)
- -



ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
M38-1 (CANH) BR No. 1 CAN junction connector
(for Bus 5)
M38-2 (CANL) W
M39-1 (CANH) B Television camera assembly*1
(for Bus 5)
M39-2 (CANL) W
M40-1 (CANH) GR Blind spot monitor sensor LH*2
(for Bus 5)
M40-2 (CANL) W
M41-1 (CANH) B CAN junction terminal
(for Bus 5)
M41-2 (CANL) W

·

*1: w/ Parking Assist Monitor System

·

*2: w/ Blind Spot Monitor System





NO. 3 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 3 CAN junction connector.

i.

Connection diagram

C367642C03
3.26,0.74 3.76,1.021 0.5,0.281 1.75,1.917 2.021,1.917 2.021,1.917 2.406,2.115 true 1.74,2.583 2.031,2.583 2.031,2.583 2.406,2.323 true 1.688,1.542 1.958,1.542 1.958,1.542 2.635,2.104 true 1.719,1.135 1.99,1.135 1.99,1.135 3.135,2.104 true 1.729,0.76 2,0.76 2,0.76 3.385,2.115 true 5.292,1.688 5.01,1.688 5.01,1.688 4.385,2.115 true 5.302,2.76 4.938,2.76 4.938,2.76 4.385,2.313 true 5.344,1.417 5.063,1.417 5.063,1.417 4.125,2.115 true 5.292,2.99 5.01,2.99 5.01,2.99 4.125,2.302 true 5.333,0.979 5.052,0.979 5.052,0.979 3.635,2.115 true 5.292,3.365 5.01,3.365 5.01,3.365 3.646,2.313 true 1.75,2.948 2.042,2.948 2.042,2.948 2.656,2.323 true 1.76,3.302 2.052,3.302 2.052,3.302 3.146,2.323 true 1.76,3.615 2.052,3.615 2.052,3.615 3.396,2.323 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.354,0.792 3.969,0.99 0.615,0.198 10 false F102 1.188,1.833 2.104,2.031 0.917,0.198 10 false CANH*b 1.198,2.5 2.115,2.698 0.917,0.198 10 false CANL*b 1.135,1.458 2.052,1.656 0.917,0.198 10 false CANH*c 1.208,2.875 2.125,3.073 0.917,0.198 10 false CANL*c 1.135,1.052 2.052,1.25 0.917,0.198 10 false CANH*d 1.208,3.208 2.125,3.406 0.917,0.198 10 false CANL*d 1.167,0.688 2.083,0.885 0.917,0.198 10 false CANH*e 1.208,3.542 2.125,3.74 0.917,0.198 10 false CANL*e 5.396,0.906 6.313,1.104 0.917,0.198 10 false CANH*f 5.354,3.302 6.271,3.5 0.917,0.198 10 false CANL*f 5.396,1.344 6.313,1.542 0.917,0.198 10 false CANH*g 5.354,1.615 6.271,1.813 0.917,0.198 10 false CANH*h 5.354,2.917 6.271,3.115 0.917,0.198 10 false CANL*g 5.365,2.688 6.281,2.885 0.917,0.198 10 false CANL*h
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
(for Bus 2)
*c to ECM
(for Bus 2)
*d to Steering Sensor
(for Bus 2)
*e to Power Steering ECU Assembly
(for Bus 2)
*f to Main Body ECU (Multiplex Network Body ECU)
(for Bus 2)
*g to 4WD ECU Assembly
(for AWD)
(for Bus 2)
*h to Headlight Leveling ECU Assembly
(w/ Automatic Headlight Beam Level Control System)
(for Bus 2)



ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F102-1 (CANH) BR No. 4 CAN junction connector
(for Bus 2)
F102-11 (CANL) W
F102-2 (CANH) B ECM
(for Bus 2)
F102-12 (CANL) W
F102-4 (CANH) BE Steering sensor
(for Bus 2)
F102-14 (CANL) W
F102-5 (CANH) P Power steering ECU assembly
(for Bus 2)
F102-15 (CANL) W
F102-6 (CANH) R Main body ECU (multiplex network body ECU)
(for Bus 2)
F102-16 (CANL) W
F102-8 (CANH) L 4WD ECU assembly*1
(for Bus 2)
F102-18 (CANL) W
F102-9 (CANH) GR Headlight leveling ECU assembly*2
(for Bus 2)
F102-19 (CANL) W

·

*1: for AWD

·

*2: w/ Automatic Headlight Beam Level Control System





NO. 4 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 4 CAN junction connector.

i.

Connection diagram

C367642C04
3.26,0.74 3.76,1.021 0.5,0.281 1.75,1.917 2.021,1.917 2.021,1.917 2.406,2.115 true 1.74,2.583 2.031,2.583 2.031,2.583 2.406,2.323 true 1.688,1.542 1.958,1.542 1.958,1.542 2.635,2.104 true 1.469,1.125 1.74,1.125 1.74,1.125 2.885,2.094 true 1.479,0.76 1.75,0.76 1.75,0.76 3.135,2.115 true 5.292,1.885 5.01,1.885 5.01,1.885 4.625,2.125 true 5.281,2.583 5,2.583 5,2.583 4.625,2.313 true 5.5,1.417 5.073,1.417 5.073,1.417 4.375,2.115 true 5.438,3.01 4.99,3.01 4.99,3.01 4.385,2.313 true 5.458,0.771 5.063,0.771 5.063,0.771 3.865,2.115 true 5.229,3.521 4.823,3.521 4.823,3.521 3.885,2.313 true 1.75,2.948 2.042,2.948 2.042,2.948 2.656,2.323 true 1.51,3.302 1.99,3.302 1.99,3.302 2.896,2.323 true 1.51,3.615 2.021,3.615 2.021,3.615 3.146,2.323 true 5.417,3.271 4.896,3.271 4.896,3.271 4.125,2.323 true 5.448,1.115 5.063,1.115 5.063,1.115 4.125,2.104 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.354,0.792 3.969,0.99 0.615,0.198 10 false F103 1.188,1.833 2.104,2.031 0.917,0.198 10 false CANH*b 1.198,2.5 2.115,2.698 0.917,0.198 10 false CANL*b 1.135,1.458 2.052,1.656 0.917,0.198 10 false CANH*c 1.208,2.875 2.125,3.073 0.917,0.198 10 false CANL*c 0.896,1.042 1.813,1.24 0.917,0.198 10 false CANH*d 0.979,3.208 1.896,3.406 0.917,0.198 10 false CANL*d 0.917,0.677 1.833,0.875 0.917,0.198 10 false CANH*e 0.948,3.531 1.865,3.729 0.917,0.198 10 false CANL*e 5.51,0.698 6.427,0.896 0.917,0.198 10 false CANH*f 5.313,3.448 6.229,3.646 0.917,0.198 10 false CANL*f 5.51,1.042 6.427,1.24 0.917,0.198 10 false CANH*g 5.479,3.188 6.396,3.385 0.917,0.198 10 false CANL*g 5.521,2.948 6.438,3.146 0.917,0.198 10 false CANL*h 5.344,2.51 6.26,2.708 0.917,0.198 10 false CANL*i 5.563,1.344 6.479,1.542 0.917,0.198 10 false CANH*h 5.354,1.813 6.271,2.01 0.917,0.198 10 false CANH*i
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to No. 3 CAN Junction Connector
(for Bus 2)
*c to Skid Control ECU (Brake Actuator Assembly)
(for Bus 2)
*d to Air Conditioning Amplifier Assembly
(for Bus 2)
*e to Airbag Sensor Assembly
(for Bus 2)
*f to Certification ECU (Smart Key ECU Assembly)
(w/ Smart Entry and Start System)
(for Bus 2)
*g to Combination Meter Assembly
(for Bus 2)
*h to Clearance Warning ECU Assembly
(w/ Toyota Parking Assist-sensor System)
(for Bus 2)
*i to Central Gateway ECU (Network Gateway ECU)
(for Bus 2)
- -



ii.

Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F103-1 (CANH) BR No. 3 CAN junction connector
(for Bus 2)
F103-11 (CANL) W
F103-2 (CANH) GR Skid control ECU (brake actuator assembly)
(for Bus 2)
F103-12 (CANL) W
F103-3 (CANH) BE Air conditioning amplifier assembly
(for Bus 2)
F103-13 (CANL) W
F103-4 (CANH) Y Airbag sensor assembly
(for Bus 2)
F103-14 (CANL) W
F103-7 (CANH) G Certification ECU (smart key ECU assembly)*1
(for Bus 2)
F103-17 (CANL) W
F103-8 (CANH) SB Combination meter assembly
(for Bus 2)
F103-18 (CANL) W
F103-9 (CANH) LG Clearance warning ECU assembly*2
(for Bus 2)
F103-19 (CANL) W
F103-10 (CANH) P Central gateway ECU (network gateway ECU)
(for Bus 2)
F103-20 (CANL) W

·

*1: w/ Smart Entry and Start System

·

*2: w/ Toyota Parking Assist-sensor System





NO. 5 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 5 CAN junction connector.

i.

Connection diagram

C292404C05
3.177,0.302 3.594,0.625 0.417,0.323 2.729,1.698 2.188,0.885 2.188,0.885 2.042,0.885 true 2.979,1.698 2.51,0.552 2.51,0.552 2.375,0.552 true 3.25,1.698 4.219,0.74 4.219,0.74 4.448,0.74 true 3.24,1.927 4.219,2.469 4.219,2.469 4.448,2.469 true 2.469,2.448 2.583,2.448 2.583,2.448 2.99,1.917 true 2.167,2.229 2.281,2.229 2.281,2.229 2.719,1.906 true 3.115,1.688 2.729,0.26 2.729,0.26 2.573,0.26 true 2.667,2.646 2.781,2.646 2.781,2.646 3.115,1.927 true 0.063,0.031 0.375,0.229 0.313,0.198 10 false *a 3.24,0.365 3.615,0.563 0.375,0.198 10 false F111 1.469,0.792 2.385,0.99 0.917,0.198 10 false CANH*b 1.792,0.448 2.708,0.646 0.917,0.198 10 false CANH*c 2,0.156 2.917,0.354 0.917,0.198 10 false CANH*d 2.104,2.563 3.021,2.76 0.917,0.198 10 false CANL*d 1.885,2.354 2.802,2.552 0.917,0.198 10 false CANL*c 1.615,2.135 2.531,2.333 0.917,0.198 10 false CANL*b 4.542,0.646 5.458,0.844 0.917,0.198 10 false CANH*e 4.531,2.375 5.448,2.573 0.917,0.198 10 false CANL*e
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Multiplex Network Door ECU
(w/ Power Back Door System)
(for Sub Bus 1)
*c to Position Control ECU and Switch Assembly
(w/ Seat Position Memory System)
(for Sub Bus 1)
*d to Outer Mirror Control ECU Assembly (for Driver Side)
(w/ Seat Position Memory System)
(for Sub Bus 1)
*e to No. 6 CAN Junction Connector
(for Sub Bus 1)
- -



ii.

Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F111-1 (CANH) L Multiplex network door ECU*1
(for Sub bus 1)
F111-12 (CANL) W
F111-3 (CANH) P Position control ECU and switch assembly*2
(for Sub bus 1)
F111-14 (CANL) W
F111-4 (CANH) SB Outer mirror control ECU assembly (for driver side)*2
(for Sub bus 1)
F111-15 (CANL) P
F111-5 (CANH) B No. 6 CAN junction connector
(for Sub bus 1)
F111-16 (CANL) W

·

*1: w/ Power Back Door System

·

*2: w/ Seat Position Memory System





NO. 6 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 6 CAN junction connector.

i.

Connection diagram

C292404C06
3.177,0.302 3.594,0.625 0.417,0.323 2.865,1.698 2.323,0.885 2.323,0.885 2.177,0.885 true 2.979,1.698 2.51,0.552 2.51,0.552 2.375,0.552 true 3.25,1.698 4.219,0.74 4.219,0.74 4.448,0.74 true 3.24,1.927 4.219,2.469 4.219,2.469 4.448,2.469 true 2.521,2.521 2.625,2.521 2.625,2.521 2.99,1.917 true 2.302,2.229 2.417,2.229 2.417,2.229 2.854,1.906 true 0.063,0.031 0.375,0.229 0.313,0.198 10 false *a 3.24,0.375 3.708,0.625 0.469,0.25 10 false F112 1.615,0.792 2.531,0.99 0.917,0.198 10 false CANH*b 1.792,0.448 2.708,0.646 0.917,0.198 10 false CANH*c 4.542,0.646 5.458,0.844 0.917,0.198 10 false CANH*d 4.542,2.365 5.458,2.563 0.917,0.198 10 false CANL*d 1.958,2.427 2.875,2.625 0.917,0.198 10 false CANL*c 1.75,2.135 2.667,2.333 0.917,0.198 10 false CANL*b
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)
(for Sub Bus 1)
*c to Outer Mirror Control ECU Assembly (for Front Passenger Side)
(w/ Seat Position Memory System)
(for Sub Bus 1)
*d to No. 5 CAN Junction Connector
(for Sub Bus 1)



ii.

Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F112-2 (CANH) G Main body ECU (multiplex network body ECU)
(for Sub bus 1)
F112-13 (CANL) W
F112-3 (CANH) LG Outer mirror control ECU assembly (for front passenger side)*
(for Sub bus 1)
F112-14 (CANL) W
F112-5 (CANH) B No. 5 CAN junction connector
(for Sub bus 1)
F112-16 (CANL) W

*: w/ Seat Position Memory System




NO. 3 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 3 CAN junction connector.

i.

Connection diagram

C367642C10
3.26,0.198 3.76,0.479 0.5,0.281 1.75,1.917 2.021,1.917 2.021,1.917 2.406,2.115 true 1.74,2.583 2.031,2.583 2.031,2.583 2.406,2.323 true 1.76,1.646 2,1.646 2,1.646 2.635,2.104 true 1.75,1.375 2.01,1.375 2.01,1.375 2.885,2.094 true 1.76,1.104 2,1.104 2,1.104 3.135,2.115 true 5.292,1.885 5.01,1.885 5.01,1.885 4.625,2.125 true 5.281,2.583 5,2.583 5,2.583 4.625,2.313 true 5.458,0.771 5.063,0.771 5.063,0.771 3.865,2.115 true 5.448,3.521 4.979,3.521 4.979,3.521 3.635,2.313 true 1.75,2.854 2.031,2.854 2.031,2.854 2.656,2.323 true 1.76,3.104 2.042,3.104 2.042,3.104 2.896,2.323 true 1.76,3.313 2.125,3.313 2.125,3.313 3.146,2.323 true 5.448,3.271 4.99,3.271 4.99,3.271 3.885,2.323 true 5.448,1.115 5.063,1.115 5.063,1.115 4.125,2.104 true 1.76,0.781 2,0.781 2,0.781 3.385,2.104 true 5.417,0.521 5.021,0.521 5.021,0.521 3.625,2.125 true 1.781,3.552 2.146,3.552 2.146,3.552 3.396,2.323 true 5.458,3.01 5.01,3.01 5.01,3.01 4.135,2.323 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.354,0.271 3.969,0.469 0.615,0.198 10 false F102 1.188,1.833 2.104,2.031 0.917,0.198 10 false CANH*b 1.198,2.5 2.115,2.698 0.917,0.198 10 false CANL*b 1.219,1.563 2.135,1.76 0.917,0.198 10 false CANH*c 1.219,2.781 2.135,2.979 0.917,0.198 10 false CANL*c 1.208,1.313 2.125,1.51 0.917,0.198 10 false CANH*d 1.219,3.031 2.135,3.229 0.917,0.198 10 false CANL*d 1.198,1.031 2.115,1.229 0.917,0.198 10 false CANH*e 1.229,3.25 2.146,3.448 0.917,0.198 10 false CANL*e 1.229,0.719 2.146,0.917 0.917,0.198 10 false CANH*f 1.26,3.49 2.177,3.688 0.917,0.198 10 false CANL*f 5.469,0.458 6.385,0.656 0.917,0.198 10 false CANH*g 5.5,3.448 6.417,3.646 0.917,0.198 10 false CANL*g 5.51,3.198 6.427,3.396 0.917,0.198 10 false CANL*h 5.521,2.938 6.438,3.135 0.917,0.198 10 false CANL*i 5.521,0.708 6.438,0.906 0.917,0.198 10 false CANH*h 5.51,1.052 6.427,1.25 0.917,0.198 10 false CANH*i 5.365,1.823 6.281,2.021 0.917,0.198 10 false CANH*j 5.344,2.51 6.26,2.708 0.917,0.198 10 false CANL*j
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
(for Bus 2)
*c to ECM
(for Bus 2)
*d to Air Conditioning Amplifier Assembly
(for Bus 2)
*e to Airbag Sensor Assembly
(for Bus 2)
*f to Clearance Warning ECU Assembly
(w/ Toyota Parking Assist-sensor System)
(for Bus 2)
*g to Main Body ECU (Multiplex Network Body ECU)
(for Bus 2)
*h to Certification ECU (Smart Key ECU Assembly)
(w/ Smart Entry and Start System)
(for Bus 2)
*i to 4WD ECU Assembly
(for AWD)
(for Bus 2)
*j to Central Gateway ECU (Network Gateway ECU)
(for Bus 2)



ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F102-1 (CANH) BR No. 4 CAN junction connector
(for Bus 2)
F102-11 (CANL) W
F102-2 (CANH) B ECM
(for Bus 2)
F102-12 (CANL) W
F102-3 (CANH) BE Air conditioning amplifier assembly
(for Bus 2)
F102-13 (CANL) W
F102-4 (CANH) Y Airbag sensor assembly
(for Bus 2)
F102-14 (CANL) W
F102-5 (CANH) LG Clearance warning ECU assembly*1
(for Bus 2)
F102-15 (CANL) W
F102-6 (CANH) R Main body ECU (multiplex network body ECU)
(for Bus 2)
F102-16 (CANL) W
F102-7 (CANH) G Certification ECU (smart key ECU assembly)*2
(for Bus 2)
F102-17 (CANL) W
F102-8 (CANH) L 4WD ECU assembly*3
(for Bus 2)
F102-18 (CANL) W
F102-10 (CANH) P Central gateway ECU (network gateway ECU)
(for Bus 2)
F102-20 (CANL) W

·

*1: w/ Toyota Parking Assist-sensor System

·

*2: w/ Smart Entry and Start System

·

*3: for AWD





NO. 4 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 4 CAN junction connector.

i.

Connection diagram

C367642C05
3.26,0.74 3.76,1.021 0.5,0.281 1.75,1.917 2.021,1.917 2.021,1.917 2.406,2.115 true 1.74,2.583 2.031,2.583 2.031,2.583 2.406,2.323 true 1.688,1.542 1.958,1.542 1.958,1.542 2.635,2.104 true 1.74,1.167 2.073,1.167 2.073,1.167 3.135,2.115 true 1.75,2.948 2.042,2.948 2.042,2.948 2.656,2.323 true 1.75,3.302 2.313,3.302 2.313,3.302 3.167,2.313 true 5.417,3.271 4.896,3.271 4.896,3.271 4.125,2.323 true 5.448,1.115 5.063,1.115 5.063,1.115 4.125,2.104 true 1.719,0.823 2.052,0.823 2.052,0.823 3.385,2.104 true 1.771,3.615 2.281,3.615 2.281,3.615 3.406,2.323 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.354,0.792 3.969,0.99 0.615,0.198 10 false F103 1.188,1.833 2.104,2.031 0.917,0.198 10 false CANH*b 1.198,2.5 2.115,2.698 0.917,0.198 10 false CANL*b 1.135,1.458 2.052,1.656 0.917,0.198 10 false CANH*c 1.208,2.875 2.125,3.073 0.917,0.198 10 false CANL*c 1.188,1.083 2.104,1.281 0.917,0.198 10 false CANH*d 1.208,3.219 2.125,3.417 0.917,0.198 10 false CANL*d 1.156,0.74 2.073,0.938 0.917,0.198 10 false CANH*e 1.24,3.521 2.156,3.719 0.917,0.198 10 false CANL*e 5.51,1.042 6.427,1.24 0.917,0.198 10 false CANH*f 5.469,3.188 6.385,3.385 0.917,0.198 10 false CANL*f
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to No. 3 CAN Junction Connector
(for Bus 2)
*c to Skid Control ECU (Brake Actuator Assembly)
(for Bus 2)
*d to Steering Sensor
(for Bus 2)
*e to Power Steering ECU Assembly
(for Bus 2)
*f to Combination Meter Assembly
(for Bus 2)



ii.

Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F103-1 (CANH) BR No. 3 CAN junction connector
(for Bus 2)
F103-11 (CANL) W
F103-2 (CANH) GR Skid control ECU (brake actuator assembly)
(for Bus 2)
F103-12 (CANL) W
F103-4 (CANH) BE Steering sensor
(for Bus 2)
F103-14 (CANL) W
F103-5 (CANH) P Power steering ECU assembly
(for Bus 2)
F103-15 (CANL) W
F103-8 (CANH) SB Combination meter assembly
(for Bus 2)
F103-18 (CANL) W




NO. 5 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 5 CAN junction connector.

i.

Connection diagram

C292404C03
3.177,0.302 3.594,0.625 0.417,0.323 2.729,1.698 2.188,0.885 2.188,0.885 2.042,0.885 true 3.115,1.698 2.646,0.552 2.646,0.552 2.51,0.552 true 3.25,1.698 4.219,0.74 4.219,0.74 4.448,0.74 true 3.24,1.927 4.219,2.469 4.219,2.469 4.448,2.469 true 2.594,2.448 2.708,2.448 2.708,2.448 3.115,1.917 true 2.167,2.229 2.281,2.229 2.281,2.229 2.719,1.906 true 0.063,0.031 0.375,0.229 0.313,0.198 10 false *a 3.24,0.354 3.667,0.552 0.427,0.198 10 false F111 1.469,0.792 2.385,0.99 0.917,0.198 10 false CANH*b 1.927,0.448 2.844,0.646 0.917,0.198 10 false CANH*c 2.01,2.354 2.927,2.552 0.917,0.198 10 false CANL*c 1.615,2.135 2.531,2.333 0.917,0.198 10 false CANL*b 4.542,0.646 5.458,0.844 0.917,0.198 10 false CANH*d 4.531,2.375 5.448,2.573 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Multiplex Network Door ECU
(w/ Power Back Door System)
(for Sub Bus 1)
*c to Outer Mirror Control ECU Assembly (for Front Passenger Side)
(w/ Seat Position Memory System)
(for Sub Bus 1)
*d to No. 6 CAN Junction Connector
(for Sub Bus 1)



ii.

Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F111-1 (CANH) L Multiplex network door ECU*1
(for Sub bus 1)
F111-12 (CANL) W
F111-4 (CANH) SB Outer mirror control ECU assembly (for front passenger side)*2
(for Sub bus 1)
F111-15 (CANL) P
F111-5 (CANH) B No. 6 CAN junction connector
(for Sub bus 1)
F111-16 (CANL) W

·

*1: w/ Power Back Door System

·

*2: w/ Seat Position Memory System





NO. 6 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 6 CAN junction connector.

i.

Connection diagram

C292404C04
3.177,0.302 3.594,0.625 0.417,0.323 2.865,1.698 2.323,0.885 2.323,0.885 2.177,0.885 true 2.979,1.698 2.51,0.552 2.51,0.552 2.375,0.552 true 3.25,1.698 4.25,0.885 4.25,0.885 4.5,0.885 true 3.115,1.906 3.75,2.521 3.75,2.521 4,2.521 true 2.521,2.521 2.625,2.521 2.625,2.521 2.99,1.917 true 2.302,2.229 2.417,2.229 2.417,2.229 2.854,1.906 true 3.115,1.698 3.917,0.552 3.917,0.552 4.167,0.552 true 3.229,1.917 3.917,2.229 3.917,2.229 4.167,2.229 true 0.063,0.031 0.375,0.229 0.313,0.198 10 false *a 3.229,0.354 3.625,0.563 0.396,0.208 10 false F112 1.615,0.792 2.531,0.99 0.917,0.198 10 false CANH*b 1.792,0.448 2.708,0.646 0.917,0.198 10 false CANH*c 4.573,0.792 5.49,0.99 0.917,0.198 10 false CANH*e 4.24,2.135 5.156,2.333 0.917,0.198 10 false CANL*e 1.958,2.427 2.875,2.625 0.917,0.198 10 false CANL*c 1.75,2.135 2.667,2.333 0.917,0.198 10 false CANL*b 4.24,0.458 5.156,0.656 0.917,0.198 10 false CANH*d 4.073,2.427 4.99,2.625 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)
(for Sub Bus 1)
*c to Outer Mirror Control ECU Assembly (for Driver Side)
(w/ Seat Position Memory System)
(for Sub Bus 1)
*d to Position Control ECU and Switch Assembly
(w/ Seat Position Memory System)
(for Sub Bus 1)
*e to No. 5 CAN Junction Connector
(for Sub Bus 1)
- -



ii.

Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F112-2 (CANH) G Main body ECU (multiplex network body ECU)
(for Sub bus 1)
F112-13 (CANL) W
F112-3 (CANH) LG Outer mirror control ECU assembly (for driver side)*
(for Sub bus 1)
F112-14 (CANL) W
F112-4 (CANH) P Position control ECU and switch assembly*
(for Sub bus 1)
F112-15 (CANL) W
F112-5 (CANH) B No. 5 CAN junction connector
(for Sub bus 1)
F112-16 (CANL) W

*: w/ Seat Position Memory System




NO. 7 CAN JUNCTION CONNECTOR


a.

Check the No. 7 CAN junction connector.

i.

Connection diagram

C292404C54
3.177,0.302 3.625,0.563 0.448,0.26 2.729,1.698 2.188,0.885 2.188,0.885 2.042,0.885 true 2.844,1.698 2.375,0.552 2.375,0.552 2.24,0.552 true 3.25,1.698 4.219,0.74 4.219,0.74 4.448,0.74 true 3.24,1.927 4.219,2.469 4.219,2.469 4.448,2.469 true 2.188,2.365 2.417,2.365 2.417,2.365 2.844,1.917 true 1.99,2.135 2.24,2.135 2.24,2.135 2.719,1.906 true 3.104,1.708 2.594,0.26 2.594,0.26 2.438,0.26 true 2.375,2.583 2.573,2.583 2.573,2.583 3.104,1.917 true 0.063,0.031 0.375,0.229 0.313,0.198 10 false *a 3.24,0.354 3.771,0.604 0.531,0.25 10 false F135 1.479,0.813 2.396,1.01 0.917,0.198 10 false CANH*b 1.865,0.198 2.781,0.396 0.917,0.198 10 false CANH*c 1.823,2.521 2.74,2.719 0.917,0.198 10 false CANL*c 1.458,2.063 2.375,2.26 0.917,0.198 10 false CANL*b 4.542,0.646 5.458,0.844 0.917,0.198 10 false CANH*d*e 4.542,2.396 5.458,2.594 0.917,0.198 10 false CANL*d*e 1.635,2.302 2.552,2.5 0.917,0.198 10 false CANL*b 1.667,0.5 2.583,0.698 0.917,0.198 10 false CANH*b
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
(for Bus 3)
*c to Telematics Transceiver
(w/ Telematics Transceiver)
(for Bus 3)
*d to Navigation Receiver Assembly
(for Navigation Receiver Type)
(for Bus 3)
*e to Radio and Display Receiver Assembly
(for Radio and Display Type)
(for Bus 3)
- -



ii.

Check the connection diagram of the components which are connected to the No. 7 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F135-1 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 3)
F135-12 (CANL) W
F135-2 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 3)
F135-13 (CANL) W
F135-4 (CANH) B Telematics transceiver*1
(for Bus 3)
F135-15 (CANL) W
F135-5 (CANH) B Navigation receiver assembly*2
(for Bus 3)
F135-16 (CANL) W
F135-5 (CANH) B Radio and display receiver assembly*3
(for Bus 3)
F135-16 (CANL) W

·

*1: w/ Telematics Transceiver

·

*2: for Navigation Receiver Type

·

*3: for Radio and Display Type





CAN JUNCTION TERMINAL


a.

Check the CAN junction terminal.

i.

Connection diagram

C285687C10
2.208,0.188 2.656,0.479 0.448,0.292 3.792,0.917 4.229,1.354 4.229,1.354 4.417,1.354 true 2.979,1.365 3.177,1.365 3.177,1.365 3.583,0.917 true 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 2.302,0.229 2.917,0.427 0.615,0.198 10 false M42 4.458,1.25 5.073,1.448 0.615,0.198 10 false CANH*b 2.448,1.271 3.063,1.469 0.615,0.198 10 false CANL*b
*a Front view of wire harness connector
(to CAN Junction Terminal)
*b to No. 2 CAN Junction Connector
(for Bus 5)



ii.

Check the connection diagram of the components which are connected to the CAN junction terminal.

Terminal No. (Symbol) Wiring Color Connected to
M42-3 (CANH) B No. 2 CAN junction connector
(for Bus 5)
M42-2 (CANL) W




DLC3


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C292402C01
3.354,0.052 3.75,0.344 0.396,0.292 3.479,0.708 3.115,0.271 3.115,0.271 2.979,0.271 true 3.833,1.24 3.281,1.625 3.281,1.625 3.135,1.625 true 4.698,1.573 4.542,1.573 4.542,1.573 4.208,1.219 true 4.396,0.24 4.25,0.24 4.25,0.24 3.844,0.719 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *1 3.427,0.104 3.74,0.302 0.313,0.198 10 false F25 2.708,0.177 3.021,0.375 0.313,0.198 10 false CG 2.719,1.531 3.333,1.729 0.615,0.198 10 false CANL 4.792,1.479 5.25,1.677 0.458,0.198 10 false BAT 4.49,0.146 5.104,0.344 0.615,0.198 10 false CANH
*1 DLC3 - -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F25-6 (CANH) - F25-14 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F25-6 (CANH) - F25-4 (CG) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F25-14 (CANL) - F25-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F25-6 (CANH) - F25-16 (BAT) V - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F25-14 (CANL) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


C349819C19
1.083,1.281 1.583,1.573 0.5,0.292 3.615,2.51 3.448,2.51 3.448,2.51 3.448,1.427 true 3.24,1.302 3.24,0.771 3.24,0.771 3.115,0.771 true 3.542,1.375 3.542,0.51 3.542,0.51 3.698,0.51 true 3.115,1.979 3.271,1.979 3.271,1.979 3.271,1.438 true 3.625,1.385 3.625,0.667 3.625,0.667 3.781,0.667 true 3.885,2.354 3.719,2.354 3.719,2.354 3.719,1.438 true 3.958,2.188 3.792,2.188 3.792,2.188 3.792,1.427 true 4.042,2 3.875,2 3.875,2 3.875,1.427 true 3.917,1.292 3.917,0.854 3.917,0.854 4.073,0.854 true 3.188,2.333 3.354,2.333 3.354,2.333 3.354,1.417 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 2.698,0.708 3.188,0.885 0.49,0.177 10 false CA3H 2.729,1.917 3.281,2.135 0.552,0.219 10 false CA3L 3.677,2.427 4.167,2.604 0.49,0.177 10 false CAYH 2.802,2.281 3.292,2.458 0.49,0.177 10 false CAYL 3.76,0.427 4.25,0.604 0.49,0.177 10 false CA4H 4.135,0.771 4.688,0.99 0.552,0.219 10 false CA6L 4.031,2.094 4.521,2.271 0.49,0.177 10 false CA5H 3.958,2.26 4.51,2.479 0.552,0.219 10 false CA5L 1.177,1.354 1.74,1.708 0.563,0.354 10 false F127 4.115,1.906 4.604,2.083 0.49,0.177 10 false CA6H 3.854,0.583 4.406,0.802 0.552,0.219 10 false CA4L
*a Component without harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F127 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C361640C07
0.917,1.708 1.406,1.99 0.49,0.281 2.031,1.229 2.281,1.229 2.281,1.229 2.281,1.729 true 2.729,0.99 2.979,0.99 2.979,0.99 2.979,1.74 true 2.823,2.573 3.073,2.573 3.073,2.573 3.073,1.99 true 2.969,2.823 3.219,2.823 3.219,2.823 3.219,1.99 true 5.125,1.24 4.875,1.24 4.875,1.24 4.875,1.74 true 4.427,0.99 4.177,0.99 4.177,0.99 4.177,1.74 true 3.26,0.781 3.51,0.781 3.51,0.781 3.51,1.948 true 3.406,0.542 3.656,0.542 3.656,0.542 3.656,1.958 true 3.115,3.052 3.365,3.052 3.365,3.052 3.365,1.99 true 4.344,2.74 4.083,2.74 4.083,2.74 4.083,1.979 true 4.188,2.99 3.938,2.99 3.938,2.99 3.938,1.99 true 4.042,3.25 3.792,3.25 3.792,3.25 3.792,2 true 1.01,1.781 1.563,2.042 0.552,0.26 10 false F127 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 1.635,1.167 2.188,1.427 0.552,0.26 10 false BATT 2.333,0.927 2.885,1.188 0.552,0.26 10 false CA6L 2.417,2.5 2.969,2.76 0.552,0.26 10 false CA6H 2.563,2.74 3.115,3 0.552,0.26 10 false CA5H 5.188,1.177 5.74,1.438 0.552,0.26 10 false GND 4.49,0.917 5.042,1.177 0.552,0.26 10 false CA3H 2.99,0.479 3.542,0.74 0.552,0.26 10 false CA4H 2.875,0.719 3.427,0.979 0.552,0.26 10 false CA4L 2.729,2.99 3.281,3.25 0.552,0.26 10 false CA5L 4.385,2.677 4.938,2.938 0.552,0.26 10 false CA3L 4.229,2.927 4.781,3.188 0.552,0.26 10 false CAYL 4.135,3.156 4.688,3.417 0.552,0.26 10 false CAYH
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
V Bus Branch Lines (DLC3 - Central gateway ECU (network gateway ECU))
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F127-14 (CA6H) - F127-5 (CA6L) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 1 MΩ or higher
F127-14 (CA6H) - F127-10 (GND) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F127-5 (CA6L) - F127-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F127-14 (CA6H) - F127-1 (BATT) V - BE HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F127-5 (CA6L) - F127-1 (BATT) W - BE LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F127-18 (CA4H) - F127-17 (CA4L) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F127-18 (CA4H) - F127-10 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F127-17 (CA4L) - F127-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F127-18 (CA4H) - F127-1 (BATT) P - BE HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F127-17 (CA4L) - F127-1 (BATT) W - BE LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 3 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F127-6 (CA3H) - F127-19 (CAYH) B - B HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω
F127-21 (CA3L) - F127-20 (CAYL) W - W LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω
F127-6 (CA3H) - F127-10 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F127-21 (CA3L) - F127-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F127-6 (CA3H) - F127-1 (BATT) B - BE HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F127-21 (CA3L) - F127-1 (BATT) W - BE LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 5 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F127-15 (CA5H) - F127-16 (CA5L) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
F127-15 (CA5H) - F127-10 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F127-16 (CA5L) - F127-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F127-15 (CA5H) - F127-1 (BATT) L - BE HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F127-16 (CA5L) - F127-1 (BATT) W - BE LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM (for 1AR-FE)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>TERMINALS OF ECM

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A43 and C1 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

C289292C01
1.719,0.042 2.146,0.333 0.427,0.292 4.75,0.042 5.177,0.333 0.427,0.292 1.531,0.76 1.01,0.281 1.01,0.281 0.917,0.281 true 2.51,0.75 2.844,0.188 2.844,0.188 2.927,0.188 true 2.51,0.813 2.792,1.427 2.792,1.427 2.896,1.427 true 4.813,0.771 4.448,0.229 4.448,0.229 4.323,0.229 true 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 0.49,0.208 1.104,0.406 0.615,0.198 10 false BATT 1.813,0.083 2.271,0.281 0.458,0.198 10 false A43 2.99,0.104 3.604,0.302 0.615,0.198 10 false CANH 2.979,1.344 3.594,1.542 0.615,0.198 10 false CANL 4.875,0.094 5.333,0.292 0.458,0.198 10 false C1 4.094,0.135 4.406,0.333 0.313,0.198 10 false E1
*a Front view of wire harness connector
(to ECM)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A43-13 (CANH) - A43-26 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A43-13 (CANH) - C1-16 (E1) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A43-26 (CANL) - C1-16 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A43-13 (CANH) - A43-1 (BATT) B - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A43-26 (CANL) - A43-1 (BATT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM (for 2GR-FKS)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A43 and C1 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

C289292C23
1.719,0.042 2.146,0.333 0.427,0.292 4.75,0.042 5.177,0.333 0.427,0.292 1.531,0.76 1.01,0.281 1.01,0.281 0.917,0.281 true 2.51,0.75 2.844,0.188 2.844,0.188 2.927,0.188 true 2.51,0.813 2.792,1.427 2.792,1.427 2.896,1.427 true 5.323,0.833 5.427,0.344 5.427,0.344 5.563,0.344 true 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 0.49,0.208 1.104,0.406 0.615,0.198 10 false BATT 1.813,0.083 2.271,0.281 0.458,0.198 10 false A43 2.99,0.104 3.604,0.302 0.615,0.198 10 false CANH 2.979,1.344 3.594,1.542 0.615,0.198 10 false CANL 4.875,0.094 5.333,0.292 0.458,0.198 10 false C1 5.615,0.25 5.927,0.448 0.313,0.198 10 false E1
*a Front view of wire harness connector
(to ECM)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A43-13 (CANH) - A43-26 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A43-13 (CANH) - C1-53 (E1) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A43-26 (CANL) - C1-53 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A43-13 (CANH) - A43-1 (BATT) B - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A43-26 (CANL) - A43-1 (BATT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F126 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C367669C04
3.344,0.167 3.802,0.448 0.458,0.281 2.094,1.354 2.271,1.354 2.271,1.354 2.521,1.635 true 4,2.26 3.76,2.26 3.76,2.26 3.635,1.792 true 3.677,2.563 3.427,2.563 3.427,2.563 3.302,1.792 true 2.813,2.323 3.104,2.323 3.104,2.323 3.198,1.813 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 3.729,2.49 4.344,2.688 0.615,0.198 10 false CANH 2.406,2.25 3.021,2.448 0.615,0.198 10 false CANL 4.042,2.188 4.354,2.385 0.313,0.198 10 false ES 1.958,1.281 2.115,1.479 0.156,0.198 10 false B 3.417,0.229 4.031,0.427 0.615,0.198 10 false F126
*a Front view of wire harness connector
(to Combination Meter Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F126-28 (CANH) - F126-27 (CANL) SB - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
F126-28 (CANH) - F126-31 (ES) SB - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F126-27 (CANL) - F126-31 (ES) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F126-28 (CANH) - F126-1 (B) SB - P HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F126-27 (CANL) - F126-1 (B) W - P LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


Refer to Terminals of ECU.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F18 and F19 main body ECU (multiplex network body ECU) connectors.


c.

Measure the resistance according to the value(s) in the table below.

C292339C01
2.031,0.292 2.448,0.604 0.417,0.313 4.698,0.313 5.115,0.625 0.417,0.313 2.104,2.51 2.521,2.823 0.417,0.313 2.052,1.198 2.74,0.417 2.74,0.417 2.844,0.417 true 2.135,1.198 2.969,0.635 2.969,0.635 3.083,0.635 true 5.021,1.188 5.708,0.406 5.708,0.406 5.813,0.406 true 5.104,1.198 5.938,0.635 5.938,0.635 6.052,0.635 true 3.573,2.49 4.115,2.021 4.115,2.021 4.26,2.021 true 4.281,3.01 4,3.448 4,3.448 3.885,3.448 true 1.104,0.115 1.417,0.313 0.313,0.198 10 false *a 1.927,1.979 2.24,2.177 0.313,0.198 10 false *1 2.135,0.344 2.448,0.542 0.313,0.198 10 false F18 4.802,0.354 5.115,0.552 0.313,0.198 10 false F19 2.198,2.552 2.51,2.75 0.313,0.198 10 false F25 2.906,0.333 3.521,0.531 0.615,0.198 10 false CANP 3.146,0.552 3.76,0.75 0.615,0.198 10 false CANN 5.885,0.323 6.5,0.521 0.615,0.198 10 false CANL 6.115,0.552 6.729,0.75 0.615,0.198 10 false CANH 4.344,1.938 4.656,2.135 0.313,0.198 10 false CG 3.563,3.365 4.021,3.563 0.458,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
- -


Standard Resistance:
Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F19-14 (CANH) - F19-13 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F19-14 (CANH) - F25-4 (CG) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F19-13 (CANL) - F25-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F19-14 (CANH) - F25-16 (BAT) R - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F19-13 (CANL) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Sub Bus 1 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F18-9 (CANP) - F18-10 (CANN) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
F18-9 (CANP) - F25-4 (CG) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F18-10 (CANN) - F25-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F18-9 (CANP) - F25-16 (BAT) G - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F18-10 (CANN) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

C367670C02
3.344,0.313 3.813,0.573 0.469,0.26 5.104,1.479 4.542,1.479 true 4.531,2.208 4.219,2.208 4.219,2.208 3.979,1.344 true 3.979,1.198 4.25,0.563 4.25,0.563 4.542,0.563 true 1.969,1.49 2.594,1.49 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.458,0.365 3.917,0.563 0.458,0.198 10 false A86 4.583,2.125 5.198,2.323 0.615,0.198 10 false CANH 4.604,0.49 5.219,0.688 0.615,0.198 10 false CANL 5.156,1.396 5.771,1.594 0.615,0.198 10 false +BS 1.563,1.406 2.177,1.604 0.615,0.198 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A86-22 (CANH) - A86-10 (CANL) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A86-22 (CANH) - A86-25 (GND1) GR - W HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A86-10 (CANL) - A86-25 (GND1) W - W LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A86-22 (CANH) - A86-38 (+BS) GR - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A86-10 (CANL) - A86-38 (+BS) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




STEERING SENSOR


C292358C01
3.521,0.094 3.938,0.406 0.417,0.313 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 3.615,0.135 4.073,0.333 0.458,0.198 10 false F58
*a Component without harness connected
(Steering Sensor)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F58 steering sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

C292359C01
2.385,0.219 2.781,0.552 0.396,0.333 3.896,1.229 4.375,0.854 4.375,0.854 4.51,0.854 true 3.573,1.24 4.167,1.646 4.167,1.646 4.292,1.646 true 2.708,1.063 2.833,1.063 2.833,1.063 3.26,1.219 true 2.823,1.573 2.927,1.573 2.927,1.573 3.427,1.25 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 2.469,0.281 2.927,0.479 0.458,0.198 10 false F58 4.604,0.771 5.063,0.969 0.458,0.198 10 false BAT 4.375,1.563 4.99,1.76 0.615,0.198 10 false CANH 2.354,0.979 2.813,1.177 0.458,0.198 10 false ESS 2.396,1.5 3.01,1.698 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Steering Sensor)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F58-3 (CANH) - F58-2 (CANL) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F58-3 (CANH) - F58-1 (ESS) BE - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F58-2 (CANL) - F58-1 (ESS) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F58-3 (CANH) - F58-5 (BAT) BE - BE HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F58-2 (CANL) - F58-5 (BAT) W - BE LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


Refer to Terminals of ECU.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the p1 and p2 power steering ECU assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

C292352C01
1.083,0.865 1.479,1.156 0.396,0.292 4.865,0.167 5.26,0.458 0.396,0.292 2.302,1.281 2.656,0.76 2.656,0.76 2.76,0.76 true 2.302,1.479 2.719,1.26 2.719,1.26 2.844,1.26 true 5.479,1.104 5.885,0.896 5.885,0.896 6,0.896 true 4.156,0.938 4.26,0.938 4.26,0.938 4.594,1.104 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 1.208,0.896 1.521,1.094 0.313,0.198 10 false p1 5,0.198 5.313,0.396 0.313,0.198 10 false p2 2.844,0.667 3.458,0.865 0.615,0.198 10 false CANH 2.927,1.177 3.542,1.375 0.615,0.198 10 false CANL 3.844,0.833 4.302,1.031 0.458,0.198 10 false PIG 6.104,0.813 6.719,1.01 0.615,0.198 10 false PGND
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
p1-4 (CANH) - p1-8 (CANL) W - B HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
p1-4 (CANH) - p2-2 (PGND) W - B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
p1-8 (CANL) - p2-2 (PGND) B - B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
p1-4 (CANH) - p2-1 (PIG) W - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
p1-8 (CANL) - p2-1 (PIG) B - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIRBAG SENSOR ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F38 airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C292356C01
1.51,0.177 1.938,0.479 0.427,0.302 4.885,0.146 5.292,0.458 0.406,0.313 1.521,1.052 1.115,0.385 1.115,0.385 1.01,0.385 true 0.969,1.583 1.094,1.583 1.094,1.583 1.406,1.271 true 1.698,1.271 1.948,1.656 1.948,1.656 2.073,1.656 true 5.698,1.323 6.083,1.625 6.083,1.625 6.219,1.625 true 0.365,0.083 0.677,0.281 0.313,0.198 10 false *a 1.604,0.24 2.063,0.438 0.458,0.198 10 false F38 0.563,0.292 1.177,0.49 0.615,0.198 10 false CANH 0.521,1.479 1.135,1.677 0.615,0.198 10 false CANL 2.146,1.552 2.458,1.75 0.313,0.198 10 false E1 3.677,0.104 3.99,0.302 0.313,0.198 10 false *1 4.969,0.198 5.281,0.396 0.313,0.198 10 false F25 6.302,1.531 6.76,1.729 0.458,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F38-13 (CANH) - F38-22 (CANL) Y - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F38-13 (CANH) - F38-25 (E1) Y - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F38-22 (CANL) - F38-25 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F38-13 (CANH) - F25-16 (BAT) Y - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F38-22 (CANL) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F80 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C292365C01
2.573,0.25 2.99,0.552 0.417,0.302 3.729,1.229 4.521,0.688 4.521,0.688 4.677,0.688 true 3.625,1.229 4.448,0.417 4.448,0.417 4.594,0.417 true 3.906,1.24 4.688,0.927 4.688,0.927 4.802,0.927 true 2.365,1.542 2.479,1.542 2.479,1.542 2.677,1.365 true 2.667,0.292 3.125,0.49 0.458,0.198 10 false F80 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 2.208,1.438 2.365,1.635 0.156,0.198 10 false B 4.875,0.844 5.333,1.042 0.458,0.198 10 false GND 4.688,0.323 5.302,0.521 0.615,0.198 10 false CANH 4.76,0.594 5.375,0.792 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F80-11 (CANH) - F80-12 (CANL) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F80-11 (CANH) - F80-14 (GND) BE - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F80-12 (CANL) - F80-14 (GND) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F80-11 (CANH) - F80-21 (B) BE - P HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F80-12 (CANL) - F80-21 (B) W - P LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Entry and Start System)


Refer to Terminals of ECU.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F13 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

C292362C01
3.365,0.104 3.792,0.396 0.427,0.292 2.24,1.438 2.365,1.438 2.365,1.438 2.771,1.021 true 4.073,0.865 4.427,0.281 4.427,0.281 4.552,0.281 true 4.198,0.865 4.635,0.479 4.635,0.479 4.74,0.479 true 4.448,0.854 4.729,1.083 4.729,1.083 4.854,1.083 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 3.469,0.146 3.927,0.344 0.458,0.198 10 false F13 2.094,1.323 2.25,1.521 0.156,0.198 10 false E 4.635,0.188 5.25,0.385 0.615,0.198 10 false CANH 4.833,0.385 5.448,0.583 0.615,0.198 10 false CANL 4.906,0.979 5.219,1.177 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F13-7 (CANH) - F13-8 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F13-7 (CANH) - F13-11 (E) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F13-8 (CANL) - F13-11 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F13-7 (CANH) - F13-10 (+B) G - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F13-8 (CANL) - F13-10 (+B) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F114 and F116 navigation receiver assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

C292346C01
4.969,0.042 5.396,0.365 0.427,0.323 1.708,0.052 2.135,0.375 0.427,0.323 2.115,1.115 2.854,0.615 2.854,0.615 2.979,0.615 true 2.021,1.104 2.698,0.156 2.698,0.156 2.813,0.156 true 5.021,1.26 4.677,1.646 4.677,1.646 4.365,1.646 true 6.156,0.563 6.021,0.563 6.021,0.563 5.646,0.938 true 0.052,0.031 0.365,0.229 0.313,0.198 10 false *a 1.771,0.115 2.229,0.313 0.458,0.198 10 false F116 5.031,0.094 5.563,0.302 0.531,0.208 10 false F114 2.896,0.063 3.51,0.26 0.615,0.198 10 false CANH 3.073,0.521 3.688,0.719 0.615,0.198 10 false CANL 3.927,1.531 4.542,1.729 0.615,0.198 10 false GND1 6.24,0.469 6.698,0.667 0.458,0.198 10 false +B1
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F116-9 (CANH) - F116-10 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F116-9 (CANH) - F114-7 (GND1) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F116-10 (CANL) - F114-7 (GND1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F116-9 (CANH) - F114-4 (+B1) B - LA-SB HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F116-10 (CANL) - F114-4 (+B1) W - LA-SB LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F69 and F71 radio and display receiver assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

C292346C06
4.969,0.042 5.396,0.365 0.427,0.323 1.708,0.052 2.135,0.375 0.427,0.323 2.115,1.115 2.854,0.615 2.854,0.615 2.979,0.615 true 2.021,1.104 2.698,0.156 2.698,0.156 2.813,0.156 true 5.021,1.26 4.677,1.646 4.677,1.646 4.365,1.646 true 6.156,0.563 6.021,0.563 6.021,0.563 5.646,0.938 true 0.052,0.031 0.365,0.229 0.313,0.198 10 false *a 1.802,0.115 2.26,0.313 0.458,0.198 10 false F71 5.063,0.104 5.594,0.313 0.531,0.208 10 false F69 2.896,0.063 3.51,0.26 0.615,0.198 10 false CANH 3.073,0.521 3.688,0.719 0.615,0.198 10 false CANL 3.927,1.531 4.542,1.729 0.615,0.198 10 false GND1 6.24,0.469 6.698,0.667 0.458,0.198 10 false +B1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F71-9 (CANH) - F71-10 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F71-9 (CANH) - F69-7 (GND1) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F71-10 (CANL) - F69-7 (GND1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F71-9 (CANH) - F69-4 (+B1) B - LA-SB HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F71-10 (CANL) - F69-4 (+B1) W - LA-SB LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CLEARANCE WARNING ECU ASSEMBLY (w/ Toyota Parking Assist-sensor System)


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F87 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C292374C01
1.667,0.167 2.094,0.469 0.427,0.302 4.823,0.052 5.25,0.354 0.427,0.302 2.813,0.875 2.927,0.344 2.927,0.344 3.01,0.344 true 1.406,1.51 1.51,1.51 1.51,1.51 1.698,1.01 true 2.917,0.875 3.125,0.698 3.125,0.698 3.219,0.698 true 5.667,1.167 5.99,1.583 5.99,1.583 6.104,1.583 true 0.344,0.156 0.656,0.354 0.313,0.198 10 false *a 3.542,0.135 3.854,0.333 0.313,0.198 10 false *1 1.76,0.208 2.219,0.406 0.458,0.198 10 false F87 3.292,0.604 3.604,0.802 0.313,0.198 10 false R2 3.073,0.25 3.385,0.448 0.313,0.198 10 false R1 1.26,1.417 1.417,1.615 0.156,0.198 10 false E 4.917,0.104 5.229,0.302 0.313,0.198 10 false F25 6.188,1.479 6.646,1.677 0.458,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F87-17 (R1) - F87-18 (R2) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F87-17 (R1) - F87-27 (E) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F87-18 (R2) - F87-27 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F87-17 (R1) - F25-16 (BAT) LG - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F87-18 (R2) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




4WD ECU ASSEMBLY (for AWD)


Refer to Terminals of ECU.

Click hereDrivetrain>MF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F14 4WD ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C292371C01
1.938,0.083 2.365,0.396 0.427,0.313 4.792,0.073 5.219,0.385 0.427,0.313 2.813,0.875 3.073,0.281 3.073,0.281 3.177,0.281 true 1.542,1.063 1.823,1.521 1.823,1.521 2.021,1.521 true 1.427,1.073 1.25,1.521 1.25,1.521 1.125,1.521 true 5.646,1.156 5.927,1.615 5.927,1.615 6.125,1.615 true 0.885,0.104 1.198,0.302 0.313,0.198 10 false *a 3.646,0.094 3.958,0.292 0.313,0.198 10 false *1 2.031,0.146 2.49,0.344 0.458,0.198 10 false F14 4.885,0.135 5.198,0.333 0.313,0.198 10 false F25 3.25,0.188 3.708,0.385 0.458,0.198 10 false GND 2.104,1.427 2.719,1.625 0.615,0.198 10 false CANH 0.688,1.438 1.302,1.635 0.615,0.198 10 false CANL 6.198,1.531 6.656,1.729 0.458,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to 4WD ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F14-6 (CANH) - F14-5 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F14-6 (CANH) - F14-4 (GND) L - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F14-5 (CANL) - F14-4 (GND) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F14-6 (CANH) - F25-16 (BAT) L - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F14-5 (CANL) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




HEADLIGHT LEVELING ECU ASSEMBLY (w/ Automatic Headlight Beam Level Control System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A67 headlight leveling ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C295181C01
2.052,0.115 2.479,0.396 0.427,0.281 5,0.083 5.427,0.365 0.427,0.281 5.865,1.25 6.385,1.51 6.385,1.51 6.531,1.51 true 2.625,0.896 2.896,0.313 2.896,0.313 3,0.313 true 2.729,0.896 3.063,0.5 3.063,0.5 3.188,0.5 true 2.938,0.906 3.229,1.135 3.229,1.135 3.344,1.135 true 0.979,0.104 1.292,0.302 0.313,0.198 10 false *a 2.135,0.156 2.594,0.354 0.458,0.198 10 false A67 5.094,0.125 5.406,0.323 0.313,0.198 10 false F25 3.917,0.094 4.229,0.292 0.313,0.198 10 false *1 6.615,1.427 7.073,1.625 0.458,0.198 10 false BAT 3.063,0.219 3.677,0.417 0.615,0.198 10 false CANH 3.26,0.406 3.875,0.604 0.615,0.198 10 false CANL 3.438,1.042 3.75,1.24 0.313,0.198 10 false E1
*1 DLC3 - -
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A67-6 (CANH) - A67-7 (CANL) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A67-6 (CANH) - A67-9 (E1) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A67-7 (CANL) - A67-9 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A67-6 (CANH) - F25-16 (BAT) GR - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A67-7 (CANL) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver Side) (w/ Seat Position Memory System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H2 or I2 outer mirror control ECU assembly (for driver side) connector.


c.

Measure the resistance according to the value(s) in the table below.

C292392C01
2.125,0.583 2.552,0.865 0.427,0.281 2.125,0.917 2.552,1.198 0.427,0.281 3.792,0.906 4.24,0.302 4.24,0.302 4.344,0.302 true 3.927,0.896 4.354,0.698 4.354,0.698 4.49,0.698 true 2.854,1.552 2.927,1.552 2.927,1.552 3.208,1.115 true 3.323,1.125 3.552,1.531 3.552,1.531 3.656,1.531 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 2.292,0.625 2.75,0.823 0.458,0.198 10 false I2 2.26,0.958 2.573,1.156 0.313,0.198 10 false H2 2.646,0.615 2.958,0.813 0.313,0.198 10 false *A 2.646,0.938 2.958,1.135 0.313,0.198 10 false *B 4.417,0.208 5.031,0.406 0.615,0.198 10 false CPUB 4.552,0.604 5.01,0.802 0.458,0.198 10 false GND 2.417,1.458 3.031,1.656 0.615,0.198 10 false CANN 3.74,1.427 4.354,1.625 0.615,0.198 10 false CANP
*A for LHD *B for RHD
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Driver Side))
- -


Standard Resistance:
for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I2-9 (CANP) - I2-8 (CANN) SB - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I2-9 (CANP) - I2-7 (GND) SB - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I2-8 (CANN) - I2-7 (GND) P - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I2-9 (CANP) - I2-6 (CPUB) SB - BE HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I2-8 (CANN) - I2-6 (CPUB) P - BE LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H2-9 (CANP) - H2-8 (CANN) SB - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
H2-9 (CANP) - H2-7 (GND) SB - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H2-8 (CANN) - H2-7 (GND) V - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H2-9 (CANP) - H2-6 (CPUB) SB - BE HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H2-8 (CANN) - H2-6 (CPUB) V - BE LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY (for Front Passenger Side) (w/ Seat Position Memory System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H2 or I2 outer mirror control ECU assembly (for front passenger side) connector.


c.

Measure the resistance according to the value(s) in the table below.

C292392C02
2.125,0.583 2.552,0.865 0.427,0.281 2.125,0.917 2.552,1.198 0.427,0.281 3.792,0.906 4.24,0.302 4.24,0.302 4.344,0.302 true 3.927,0.896 4.354,0.698 4.354,0.698 4.49,0.698 true 2.854,1.552 2.927,1.552 2.927,1.552 3.208,1.115 true 3.323,1.125 3.552,1.531 3.552,1.531 3.656,1.531 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 2.292,0.958 2.75,1.156 0.458,0.198 10 false I2 2.26,0.625 2.573,0.823 0.313,0.198 10 false H2 2.646,0.615 2.958,0.813 0.313,0.198 10 false *A 2.646,0.938 2.958,1.135 0.313,0.198 10 false *B 4.417,0.208 5.031,0.406 0.615,0.198 10 false CPUB 4.552,0.604 5.01,0.802 0.458,0.198 10 false GND 2.417,1.458 3.031,1.656 0.615,0.198 10 false CANN 3.74,1.427 4.354,1.625 0.615,0.198 10 false CANP
*A for LHD *B for RHD
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Front Passenger Side))
- -


Standard Resistance:
for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H2-9 (CANP) - H2-8 (CANN) SB - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
H2-9 (CANP) - H2-7 (GND) SB - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H2-8 (CANN) - H2-7 (GND) V - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H2-9 (CANP) - H2-6 (CPUB) SB - BE HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H2-8 (CANN) - H2-6 (CPUB) V - BE LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I2-9 (CANP) - I2-8 (CANN) SB - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I2-9 (CANP) - I2-7 (GND) SB - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I2-8 (CANN) - I2-7 (GND) P - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I2-9 (CANP) - I2-6 (CPUB) SB - BE HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I2-8 (CANN) - I2-6 (CPUB) P - BE LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




POSITION CONTROL ECU AND SWITCH ASSEMBLY (for LHD w/ Seat Position Memory System)


Refer to Terminals of ECU.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the e6 and e7 position control ECU and switch assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

C292395C05
1.427,0.135 1.854,0.469 0.427,0.333 4.125,0.104 4.552,0.438 0.427,0.333 1.823,1.042 1.385,0.781 1.385,0.781 1.25,0.781 true 1.323,1.604 1.49,1.604 1.49,1.604 1.813,1.292 true 4.656,1.323 4.469,1.594 4.469,1.594 4.375,1.594 true 4.771,1.344 5.385,1.625 5.385,1.625 5.5,1.625 true 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 1.573,0.208 2.031,0.406 0.458,0.198 10 false e6 0.885,0.698 1.365,0.896 0.479,0.198 10 false GND 1.073,1.521 1.406,1.719 0.333,0.198 10 false +B 4.271,0.167 4.729,0.365 0.458,0.198 10 false e7 3.948,1.5 4.563,1.698 0.615,0.198 10 false CANN 5.573,1.531 6.188,1.729 0.615,0.198 10 false CANP
*a Front view of wire harness connector
(to Position Control ECU and Switch Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
e7-8 (CANP) - e7-7 (CANN) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
e7-8 (CANP) - e6-2 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
e7-7 (CANN) - e6-2 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
e7-8 (CANP) - e6-7 (+B) L - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
e7-7 (CANN) - e6-7 (+B) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




POSITION CONTROL ECU AND SWITCH ASSEMBLY (for RHD w/ Seat Position Memory System)


Refer to Terminals of ECU.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the d6 and d7 position control ECU and switch assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

C292395C03
1.427,0.135 1.854,0.469 0.427,0.333 4.125,0.104 4.552,0.438 0.427,0.333 1.823,1.042 1.385,0.781 1.385,0.781 1.25,0.781 true 1.323,1.604 1.49,1.604 1.49,1.604 1.813,1.292 true 4.656,1.323 4.469,1.594 4.469,1.594 4.375,1.594 true 4.771,1.344 5.385,1.625 5.385,1.625 5.5,1.625 true 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 1.583,0.208 2.042,0.406 0.458,0.198 10 false d6 0.875,0.688 1.385,0.885 0.51,0.198 10 false GND 1.063,1.51 1.438,1.719 0.375,0.208 10 false +B 4.271,0.167 4.729,0.365 0.458,0.198 10 false d7 3.948,1.5 4.563,1.698 0.615,0.198 10 false CANN 5.573,1.531 6.188,1.729 0.615,0.198 10 false CANP
*a Front view of wire harness connector
(to Position Control ECU and Switch Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
d7-8 (CANP) - d7-7 (CANN) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
d7-8 (CANP) - d6-2 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
d7-7 (CANN) - d6-2 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
d7-8 (CANP) - d6-7 (+B) L - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
d7-7 (CANN) - d6-7 (+B) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door System)


Refer to Terminals of ECU.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the X6 and X7 multiplex network door ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

C295246C01
1.792,0.115 2.208,0.396 0.417,0.281 5.177,0.115 5.594,0.396 0.417,0.281 4.156,1.469 4.292,1.469 4.292,1.469 4.573,1.052 true 4.906,1.49 4.771,1.49 4.771,1.49 4.677,1.052 true 1.469,1.479 1.604,1.479 1.604,1.479 1.885,1.063 true 2.396,1.469 2.26,1.469 2.26,1.469 2.063,1.063 true 1.938,0.156 2.396,0.354 0.458,0.198 10 false X7 5.313,0.156 5.771,0.354 0.458,0.198 10 false X6 3.729,1.365 4.344,1.563 0.615,0.198 10 false CANP 4.979,1.385 5.594,1.583 0.615,0.198 10 false CANN 1.115,1.385 1.573,1.583 0.458,0.198 10 false GND 2.49,1.375 2.646,1.573 0.156,0.198 10 false B 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Multiplex Network Door ECU)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
X6-13 (CANP) - X6-14 (CANN) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
X6-13 (CANP) - X7-7 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
X6-14 (CANN) - X7-7 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
X6-13 (CANP) - X7-8 (B) L - G HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
X6-14 (CANN) - X7-8 (B) W - G LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the M31 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

C292415C01
4.875,0.094 5.271,0.375 0.396,0.281 1.854,0.115 2.26,0.396 0.406,0.281 1.438,0.5 1.51,0.5 1.51,0.5 1.948,1.021 true 1.583,1.604 1.688,1.604 1.688,1.604 1.948,1.167 true 2.323,1.177 2.563,1.573 2.563,1.573 2.667,1.573 true 5.698,1.188 5.938,1.583 5.938,1.583 6.042,1.583 true 0.74,0.146 1.052,0.344 0.313,0.198 10 false *a 3.552,0.115 3.865,0.313 0.313,0.198 10 false *1 4.948,0.135 5.26,0.333 0.313,0.198 10 false F25 1.927,0.146 2.385,0.344 0.458,0.198 10 false M31 1.031,0.396 1.646,0.594 0.615,0.198 10 false CA1P 1.167,1.5 1.781,1.698 0.615,0.198 10 false CA1N 2.74,1.469 3.354,1.667 0.615,0.198 10 false BLGD 6.125,1.479 6.583,1.677 0.458,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M31-2 (CA1P) - M31-7 (CA1N) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
M31-2 (CA1P) - M31-10 (BLGD) GR - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
M31-7 (CA1N) - M31-10 (BLGD) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
M31-2 (CA1P) - F25-16 (BAT) GR - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M31-7 (CA1N) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




DRIVING SUPPORT ECU ASSEMBLY (w/ Toyota Safety Sense)


Refer to Terminals of ECU.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F128 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C350885C05
1.583,0.146 2.083,0.406 0.5,0.26 5.01,0.188 5.406,0.458 0.396,0.271 2.719,1.271 2.719,0.583 2.719,0.583 2.865,0.583 true 2.583,1.271 2.583,0.583 2.583,0.583 2.448,0.583 true 5.833,1.667 5.833,2.156 5.833,2.156 5.969,2.156 true 2.458,1.542 2.458,2.031 2.458,2.031 2.323,2.031 true 1.677,0.198 2.146,0.458 0.469,0.26 10 false F128 0.104,0.094 0.563,0.292 0.458,0.198 10 false *a 3.76,0.094 4.219,0.292 0.458,0.198 10 false *1 2.01,0.531 2.51,0.76 0.5,0.229 10 false CA2H 2.948,0.531 3.448,0.76 0.5,0.229 10 false CA2L 1.958,1.969 2.458,2.198 0.5,0.229 10 false GND 5.094,0.25 5.573,0.563 0.479,0.313 10 false F25 6.052,2.094 6.552,2.323 0.5,0.229 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Driving Support ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F128-10 (CA2H) - F128-11 (CA2L) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F128-10 (CA2H) - F128-28 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F128-11 (CA2L) - F128-28 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F128-10 (CA2H) - F25-16 (BAT) G - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F128-11 (CA2L) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense)


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A81 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C350887C05
4.99,0.208 5.438,0.479 0.448,0.271 1.74,0.115 2.104,0.385 0.365,0.271 2.073,1.26 2.073,0.573 2.073,0.573 2.229,0.573 true 1.906,1.26 1.906,0.573 1.906,0.573 1.729,0.573 true 0.99,1.344 1.688,1.344 true 5.979,2.073 5.823,2.073 5.823,2.073 5.833,1.667 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.719,0.115 4.031,0.313 0.313,0.198 10 false *1 1.323,0.51 1.802,0.719 0.479,0.208 10 false CA2L 2.354,0.521 2.833,0.729 0.479,0.208 10 false CA2H 0.531,1.281 1.01,1.49 0.479,0.208 10 false SGND 6.094,2.01 6.573,2.219 0.479,0.208 10 false BAT 5.094,0.271 5.51,0.583 0.417,0.313 10 false F25 1.813,0.177 2.281,0.438 0.469,0.26 10 false A81
*1 DLC3 - -
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A81-3 (CA2H) - A81-2 (CA2L) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A81-3 (CA2H)- A81-1 (SGND) P - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A81-2 (CA2L) - A81-1 (SGND) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A81-3 (CA2H) - F25-16 (BAT) P - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A81-2 (CA2L) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the S18 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

C292389C10
1.771,0.083 2.198,0.354 0.427,0.271 5.104,0.063 5.531,0.333 0.427,0.271 5.948,1.167 6.198,1.542 6.198,1.542 6.323,1.542 true 2.135,0.917 2.531,0.49 2.531,0.49 2.719,0.49 true 2.146,1.167 2.531,1.583 2.531,1.583 2.688,1.583 true 2.01,1.156 1.823,1.573 1.823,1.573 1.635,1.573 true 0.677,0.083 0.99,0.281 0.313,0.198 10 false *a 3.51,0.083 3.823,0.281 0.313,0.198 10 false *1 1.865,0.146 2.292,0.417 0.427,0.271 10 false S18 5.208,0.125 5.521,0.323 0.313,0.198 10 false F25 6.396,1.448 6.854,1.646 0.458,0.198 10 false BAT 1.292,1.5 1.75,1.698 0.458,0.198 10 false GND 2.74,1.521 3.354,1.719 0.615,0.198 10 false CA1N 2.76,0.427 3.375,0.625 0.615,0.198 10 false CA1P
*1 DLC3 - -
*a Front view of wire harness connector
(to Forward Recognition Camera)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S18-5 (CA1P) - S18-11 (CA1N) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
S18-5 (CA1P) - S18-10 (GND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
S18-11 (CA1N) - S18-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
S18-5 (CA1P) - F25-16 (BAT) R - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
S18-11 (CA1N) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the X13 television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C295280C02
1.979,0.094 2.375,0.365 0.396,0.271 5.042,0.083 5.438,0.354 0.396,0.271 1.594,1.49 1.719,1.49 1.719,1.49 2.01,1.073 true 1.563,0.344 1.688,0.344 1.688,0.344 2.01,0.844 true 5.146,0.667 4.792,0.271 4.792,0.271 4.656,0.271 true 6.198,1.521 6.083,1.521 6.083,1.521 5.875,1.146 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 2.073,0.135 2.531,0.333 0.458,0.198 10 false X13 1.135,1.406 1.75,1.604 0.615,0.198 10 false CANH 1.125,0.26 1.74,0.458 0.615,0.198 10 false CANL 4.385,0.188 5,0.385 0.615,0.198 10 false CG 5.115,0.125 5.573,0.323 0.458,0.198 10 false F25 6.292,1.438 6.75,1.635 0.458,0.198 10 false BAT
*a Front view of wire harness connector
(to Television Camera Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
X13-4 (CANH) - X13-1 (CANL) L - Y HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
X13-4 (CANH) - F25-4 (CG) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
X13-1 (CANL) - F25-4 (CG) Y - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
X13-4 (CANH) - F25-16 (BAT) L - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
X13-1 (CANL) - F25-16 (BAT) Y - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




PARKING ASSIST ECU (w/ Panoramic View Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F131 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

C367683C02
3.385,0.135 3.802,0.438 0.417,0.302 3.063,1.26 3.063,0.625 3.063,0.625 2.635,0.625 true 3.813,1.448 3.813,0.594 3.813,0.594 3.594,0.594 true 3.927,1.448 3.927,0.458 3.927,0.458 4.177,0.458 true 4.115,1.26 4.115,0.646 4.115,0.646 4.365,0.646 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 3.177,0.531 3.792,0.729 0.615,0.198 10 false CANH 4.229,0.396 4.844,0.594 0.615,0.198 10 false CANL 2.406,0.563 2.719,0.76 0.313,0.198 10 false +B 4.417,0.583 5.031,0.781 0.615,0.198 10 false GND1 3.438,0.219 4.052,0.417 0.615,0.198 10 false F131
*a Front view of wire harness connector
(to Parking Assist ECU)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F131-12 (CANH) - F131-13 (CANL) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F131-12 (CANH) - F131-3 (GND1) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F131-13 (CANL) - F131-3 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F131-12 (CANH) - F131-2 (+B) LG - B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F131-13 (CANL) - F131-2 (+B) W - B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




TELEMATICS TRANSCEIVER (w/ Telematics Transceiver)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F140 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

C368355C01
3.354,0.083 3.813,0.333 0.458,0.25 2.604,1.292 2.292,0.698 2.292,0.698 2.01,0.698 true 3.729,1.479 3.365,0.427 3.365,0.427 3.135,0.427 true 3.844,1.479 4.063,0.417 4.063,0.417 4.333,0.417 true 4.146,1.292 4.292,0.708 4.292,0.708 4.563,0.708 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.792,0.635 2.104,0.833 0.313,0.198 10 false +B 2.698,0.365 3.313,0.563 0.615,0.198 10 false CANP 4.385,0.354 5,0.552 0.615,0.198 10 false CANN 4.625,0.646 5.24,0.844 0.615,0.198 10 false E 3.427,0.135 4.042,0.333 0.615,0.198 10 false F140
*a Front view of wire harness connector
(to Telematics Transceiver)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F140-15 (CANP) - F140-16 (CANN) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F140-15 (CANP) - F140-4 (E) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F140-16 (CANN) - F140-4 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F140-15 (CANP) - F140-1 (+B) B - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F140-16 (CANN) - F140-1 (+B) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher