Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _060156 2GR-FKS ENGINE CONTROL _0299070 SFI SYSTEM J

2GR-FKS ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to the IGSW terminal of the ECM.

The output signal from the MREL terminal of the ECM causes a current to flow to the coil of the semiconductor pwr integration ECU (EFI MAIN relay), closing the contacts and supplying power to terminals +B and +B2 of the ECM.

WIRING DIAGRAM

A400027E01
0.135,0.063 3.354,0.51 3.219,0.448 12 false w/ Smart Entry and Start System: 2.021,0.854 2.635,1.052 0.615,0.198 10 false IG1D 2.448,0.74 2.604,0.938 0.156,0.198 10 false 3 0.427,1.292 0.885,1.49 0.458,0.198 10 false F10 0.729,1.292 3.656,1.625 2.927,0.333 10 false Certification ECU (Smart Key ECU Assembly) 3.698,1.688 4.01,1.885 0.313,0.198 10 false 1E 4,1.688 4.156,1.885 0.156,0.198 10 false 1 3.979,2.177 4.646,2.49 0.667,0.313 10 false IG2-EFI 3.24,2.594 3.698,2.792 0.458,0.198 10 false IG2 2.385,2.135 3.125,2.344 0.74,0.208 10 false IG2-MAIN 1.615,2 1.771,2.198 0.156,0.198 10 false B 1.615,1.823 1.771,2.021 0.156,0.198 10 false 1 0.438,3.083 1.156,3.438 0.719,0.354 10 false FL MAIN 0.573,4.417 1.219,4.719 0.646,0.302 10 false Battery 1.573,3.667 1.885,3.865 0.313,0.198 10 false 1D 1.604,3.469 1.917,3.667 0.313,0.198 10 false 14 1.573,4.052 1.885,4.25 0.313,0.198 10 false 1G 1.615,3.885 1.771,4.083 0.156,0.198 10 false 5 2.052,4.604 4.458,4.896 2.406,0.292 10 false Semiconductor Pwr Integration ECU 4.594,2 4.906,2.198 0.313,0.198 10 false 1G 4.635,1.813 4.792,2.01 0.156,0.198 10 false 4 5.823,1.99 6.281,2.188 0.458,0.198 10 false A43 5.906,1.792 6.063,1.99 0.156,0.198 10 false 4 6.177,1.885 6.792,2.083 0.615,0.198 10 false IGSW 2.385,3.375 3.094,3.615 0.708,0.24 10 false EFI-MAIN 3,3.885 3.781,4.135 0.781,0.25 10 false EFI MAIN 3.74,3.385 4.458,3.688 0.719,0.302 10 false EFI NO. 2 4.594,2.854 4.906,3.052 0.313,0.198 10 false 1G 4.635,2.677 4.792,2.875 0.156,0.198 10 false 1 4.583,3.24 4.896,3.438 0.313,0.198 10 false 1G 4.635,3.073 4.792,3.271 0.156,0.198 10 false 2 5.813,2.854 6.271,3.052 0.458,0.198 10 false A43 5.896,2.677 6.052,2.875 0.156,0.198 10 false 2 6.188,2.854 6.5,3.052 0.313,0.198 10 false +B 5.813,3.24 6.271,3.438 0.458,0.198 10 false A43 5.906,3.073 6.063,3.271 0.156,0.198 10 false 3 6.167,3.229 6.625,3.427 0.458,0.198 10 false +B2 6.167,4.104 6.781,4.302 0.615,0.198 10 false MREL 5.813,4.229 6.271,4.427 0.458,0.198 10 false A43 5.865,4.052 6.177,4.25 0.313,0.198 10 false 46 4.583,4.219 4.896,4.417 0.313,0.198 10 false 1G 4.635,4.063 4.792,4.26 0.156,0.198 10 false 6 5.844,4.667 6.156,4.865 0.313,0.198 10 false C1 5.865,4.469 6.177,4.667 0.313,0.198 10 false 53 6.177,4.667 6.49,4.865 0.313,0.198 10 false E1 6.375,5.167 6.833,5.365 0.458,0.198 10 false ECM

A400028E01
0.583,4.417 1.198,4.76 0.615,0.344 10 false Battery 1.958,4.615 4.25,4.885 2.292,0.271 10 false Semiconductor Pwr Integration ECU 6.417,5.177 6.875,5.375 0.458,0.198 10 false ECM 0.406,3.094 1.208,3.365 0.802,0.271 10 false FL MAIN 0.417,1.781 0.729,1.979 0.313,0.198 10 false ST 1.615,1.99 1.771,2.188 0.156,0.198 10 false B 1.646,1.823 1.802,2.021 0.156,0.198 10 false 1 1.563,3.667 1.875,3.865 0.313,0.198 10 false 1D 1.583,3.49 1.896,3.688 0.313,0.198 10 false 14 1.552,4.042 1.865,4.24 0.313,0.198 10 false 1G 1.625,3.865 1.781,4.063 0.156,0.198 10 false 5 4.573,4.229 4.885,4.427 0.313,0.198 10 false 1G 4.625,4.052 4.781,4.25 0.156,0.198 10 false 6 4.594,3.24 4.906,3.438 0.313,0.198 10 false 1G 4.646,3.052 4.802,3.25 0.156,0.198 10 false 2 4.594,2.854 4.906,3.052 0.313,0.198 10 false 1G 4.656,2.656 4.813,2.854 0.156,0.198 10 false 1 4.583,1.99 4.896,2.188 0.313,0.198 10 false 1G 4.646,1.813 4.802,2.01 0.156,0.198 10 false 4 3.708,1.688 4.021,1.885 0.313,0.198 10 false 1E 4,1.698 4.156,1.896 0.156,0.198 10 false 1 2.396,2.135 3.188,2.344 0.792,0.208 10 false IG2-MAIN 3.229,2.594 3.688,2.792 0.458,0.198 10 false IG2 3.948,2.177 4.719,2.448 0.771,0.271 10 false IG2-EFI 2.427,3.396 3.271,3.677 0.844,0.281 10 false EFI-MAIN 3.021,3.885 4.25,4.083 1.229,0.198 10 false EFI MAIN 3.729,3.385 4.573,3.646 0.844,0.26 10 false EFI NO. 2 5.865,4.656 6.177,4.854 0.313,0.198 10 false C1 5.875,4.479 6.188,4.677 0.313,0.198 10 false 53 6.198,4.656 6.51,4.854 0.313,0.198 10 false E1 5.813,4.229 6.271,4.427 0.458,0.198 10 false A43 5.865,4.042 6.177,4.24 0.313,0.198 10 false 46 6.156,4.104 6.771,4.302 0.615,0.198 10 false MREL 5.823,3.24 6.281,3.438 0.458,0.198 10 false A43 5.896,3.063 6.052,3.26 0.156,0.198 10 false 3 6.177,3.24 6.635,3.438 0.458,0.198 10 false +B2 5.813,2.854 6.271,3.052 0.458,0.198 10 false A43 5.906,2.667 6.063,2.865 0.156,0.198 10 false 2 6.177,2.865 6.49,3.063 0.313,0.198 10 false +B 5.823,2 6.281,2.198 0.458,0.198 10 false A43 5.885,1.813 6.042,2.01 0.156,0.198 10 false 4 6.167,1.844 6.781,2.042 0.615,0.198 10 false IGSW 0.094,0.031 3.073,0.417 2.979,0.385 12 false w/o Smart Entry and Start System: 1.146,0.74 1.302,0.938 0.156,0.198 10 false 4 1.333,0.74 1.792,0.938 0.458,0.198 10 false AM2 2.01,0.729 2.469,0.927 0.458,0.198 10 false IG2 2.344,0.729 2.5,0.927 0.156,0.198 10 false 3 0.792,1.156 1.25,1.354 0.458,0.198 10 false F50 1.115,1.146 2.792,1.427 1.677,0.281 10 false Ignition Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU VOLTAGE)
a.

Disconnect the semiconductor pwr integration ECU connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1E-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK A
NG (w/o Smart Entry and Start System) B
NG (w/ Smart Entry and Start System) C



A

2.CHECK SEMICONDUCTOR PWR INTEGRATION ECU (POWER SOURCE)

B

7.CHECK HARNESS AND CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

C

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SEMICONDUCTOR PWR INTEGRATION ECU)
2.CHECK SEMICONDUCTOR PWR INTEGRATION ECU (POWER SOURCE)
A400029C01
1.042,2.01 1.406,2.302 0.365,0.292 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 1.167,2.063 1.323,2.26 0.156,0.198 10 false B 1.281,2.573 1.438,2.771 0.156,0.198 10 false 1
*1 No. 1 Engine Room Relay Bock and No. 1 Junction Block Assembly


a.

Disconnect the semiconductor pwr integration ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - SEMICONDUCTOR PWR INTEGRATION ECU)

3.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - BODY GROUND)
a.

Disconnect the semiconductor pwr integration ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1D-14 - Body ground Always Below 1 Ω
1G-5 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT SEMICONDUCTOR PWR INTEGRATION ECU (EFI MAIN RELAY, IG2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT SEMICONDUCTOR PWR INTEGRATION ECU (EFI MAIN RELAY, IG2 RELAY)
a.

Inspect the semiconductor pwr integration ECU (EFI MAIN relay, IG2 relay).

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - ECM)

NG

REPLACE SEMICONDUCTOR PWR INTEGRATION ECU

5.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - ECM)
a.

Disconnect the semiconductor pwr integration ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1G-4 - A43-4 (IGSW) Always Below 1 Ω
1G-6 - A43-46 (MREL) Always Below 1 Ω
1G-1 - A43-2 (+B) Always Below 1 Ω
1G-2 - A43-3 (+B2) Always Below 1 Ω
1G-4 or A43-4 (IGSW) - Body ground and other terminals Always 10 kΩ or higher
1G-6 or A43-46 (MREL) - Body ground and other terminals Always 10 kΩ or higher
1G-1 or A43-2 (+B) - Body ground and other terminals Always 10 kΩ or higher
1G-2 or A43-3 (+B2) - Body ground and other terminals Always 10 kΩ or higher


HINT:

If a short is detected in any of the above circuits, there may be a malfunction in the circuit of a connected ECU.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-53 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)
a.

Disconnect the ignition switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F50-4 (AM2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2GR-FKS STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SEMICONDUCTOR PWR INTEGRATION ECU)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the semiconductor pwr integration ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F10-3 (IG1D) - 1E-1 Always Below 1 Ω
F10-3 (IG1D) or 1E-1 - Body ground and other terminals Always 10 kΩ or higher



HINT:

If a short is detected in any of the above circuits, there may be a malfunction in the circuit of a connected ECU.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR