Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _060156 2GR-FKS ENGINE CONTROL _0299070 SFI SYSTEM C

2GR-FKS ENGINE CONTROL  SFI SYSTEM  P059712  Thermostat Heater Control Circuit Short to Battery  


DESCRIPTION

An electric heater is equipped to the temperature sensing portion of the thermostat. During normal driving, current does not flow to the heater and the thermostat functions as an ordinary thermostat. When the temperature of the engine increases by a large amount such as during high-load driving, control is performed to warm the heater of the temperature sensing portion, forcing the valve to open and causing a large amount of coolant to flow to the radiator.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P059712 Thermostat Heater Control Circuit Short to Battery Short in thermostat heater circuit and power supply circuit (1 trip detection logic).
·

Short in thermostat heater circuit

·

Thermostat heater (water inlet with thermostat sub-assembly)

·

ECM


Comes on DTC stored SAE Code: P0599

MONITOR DESCRIPTION

The ECM monitors the output voltage while the thermostat heater is operating.

The thermostat heater turns on and off according to ON/OFF switching of a transistor inside the ECM.

If a continuous mismatch occurs between the ECM transistor state and the output voltage, the ECM determines there is a malfunction in the thermostat heater circuit and stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A232052E44
0.438,0.031 3.292,0.333 2.854,0.302 10 false Coolant Temperature: 90°C (194°F) or higher 0.792,0.479 1.844,0.75 1.052,0.271 10 false Calculate Load 1.479,0.875 1.844,1.094 0.365,0.219 10 false 45% 1.417,2.031 1.833,2.281 0.417,0.25 10 false Idling 0.646,2.365 2.094,2.635 1.448,0.271 10 false Ignition switch ON 2.938,1.854 3.198,2.094 0.26,0.24 10 false [A] 4.813,0.406 5.115,0.635 0.302,0.229 10 false [B] 6.229,3.229 6.531,3.479 0.302,0.25 10 false [C] 4.229,3 5.531,3.281 1.302,0.281 10 false 3 seconds or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Enter the following menus: Powertrain / Engine / Data List / Calculate Load and Coolant Temperature.

7.

Start the engine and warm it up.

8.

Drive the vehicle for at least 3 seconds at the Calculate Load of 45% or more and the Coolant Temperature of 90°C (194°F) or higher [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Stop the vehicle.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P059712.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A399957E01
0.583,3.354 1.385,3.688 0.802,0.333 10 false Battery 0.531,2.635 1.354,2.958 0.823,0.323 10 false FL MAIN 0.333,2.229 0.49,2.427 0.156,0.198 10 false B 0.438,2.073 0.594,2.271 0.156,0.198 10 false 1 0.51,1.74 1.26,1.99 0.75,0.25 10 false EFI-MAIN 1.677,1.969 2.563,2.219 0.885,0.25 10 false EFI MAIN 2.521,1.188 2.833,1.385 0.313,0.198 10 false 1G 2.583,1 2.74,1.198 0.156,0.198 10 false 7 2.51,1.677 2.823,1.875 0.313,0.198 10 false 1G 2.583,1.5 2.74,1.698 0.156,0.198 10 false 6 1.344,2.458 2.573,2.813 1.229,0.354 10 false Semiconductor Pwr Integration ECU 3,1.354 3.75,1.625 0.75,0.271 10 false EFI NO. 3 3.781,1.083 3.938,1.281 0.156,0.198 10 false 1 3.958,1.073 4.479,1.344 0.521,0.271 10 false ETM+ 4.604,1.083 5.073,1.333 0.469,0.25 10 false ETM- 5.063,1.073 5.219,1.271 0.156,0.198 10 false 2 3.75,1.51 4.208,1.708 0.458,0.198 10 false C82 3.75,1.698 5.385,2.323 1.635,0.625 10 false Thermostat Heater (Water Inlet with Thermostat Sub-assembly) 5.354,1.177 5.667,1.375 0.313,0.198 10 false C1 5.354,0.99 5.667,1.188 0.313,0.198 10 false 64 5.677,1.167 6.292,1.365 0.615,0.198 10 false PTCR 5.313,3.438 5.771,3.635 0.458,0.198 10 false A43 5.375,3.24 5.688,3.438 0.313,0.198 10 false 46 5.698,3.427 6.219,3.667 0.521,0.24 10 false MREL 6.021,3.896 6.479,4.094 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
a.

Inspect the water inlet with thermostat sub-assembly.

Click hereEngine / Hybrid System>2GR-FKS (COOLING)>THERMOSTAT>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (WATER INLET WITH THERMOSTAT SUB-ASSEMBLY - ECM)

NG

REPLACE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (WATER INLET WITH THERMOSTAT SUB-ASSEMBLY - ECM)
a.

Disconnect the water inlet with thermostat sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C82-2 (ETM-) or C1-64 (PTCR) - other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P059712)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P059712)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P059712 is output B




A

B