Home › Drivetrain › MF1A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM › from 2016.11
RM3160E _52 Drivetrain _019685 MF1A TRANSFER / 4WD / AWD _0109466 DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM C

MF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM  C1241/94  Low Power Supply Voltage  


DESCRIPTION

If a malfunction in the power source circuit occurs, or a malfunction in communication with the skid control ECU (brake actuator assembly) or in a speed sensor occurs, the 4WD ECU assembly will prohibit operations by the fail-safe function.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
C1241/94 Low Power Supply Voltage
1.

When the following continues for 10 seconds or more:

-

At a vehicle speed of 3 km/h (2 mph) or more, voltage of IG1 terminal is 9.5 V or less.


2.

When either of the following is detected:

-

With the IG1 terminal voltage 9.5 V or less, communication with the skid control ECU (brake actuator assembly) is impossible.

-

Vehicle speed sensor voltage is reduced for 60 seconds or more.


3.

When the following continues for 3 seconds or more:

-

With the IG1 terminal voltage 17 V or more, communication with the skid control ECU (brake actuator assembly) is impossible.



·

Battery

·

Charging system

·

Wire harness and connector (IG1 circuit, GND circuit)

·

Brake control system

·

CAN communication system

·

4WD ECU assembly


DTC stored

WIRING DIAGRAM

C278265E17
4.979,2.698 6.542,3.063 1.563,0.365 10 false Skid Control ECU (Brake Actuator Assembly) 4.969,2.531 5.76,2.917 0.792,0.385 10 false A86 3.281,2.719 3.74,2.917 0.458,0.198 10 false F14 3.292,2.885 4.635,3.083 1.344,0.198 10 false 4WD ECU Assembly 0.75,3.271 2.698,3.458 1.948,0.188 10 false : CAN Communication Line 0.24,1.052 1.365,1.229 1.125,0.177 10 false from IG1 Circuit 2.25,1.229 2.938,1.417 0.688,0.188 10 false IG1 NO. 2 3.406,0.917 3.563,1.115 0.156,0.198 10 false 3 3.583,1.042 4.042,1.24 0.458,0.198 10 false IG1 3.427,1.823 3.583,2.021 0.156,0.198 10 false 4 3.594,1.927 4.052,2.125 0.458,0.198 10 false GND

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK FOR DTC (CAN COMMUNICATION SYSTEM AND BRAKE CONTROL SYSTEM)
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRAC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON again and check that no CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


d.

Start the engine.


e.

Drive the vehicle, accelerate to a speed of 3 km/h (2 mph) or more for 60 seconds or more, and check if the speed sensor DTC (brake control system DTC) is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRAC > Trouble Codes
50001 105
HINT:

When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before repairing each corresponding sensor.



Result:
Result Proceed to
Neither CAN communication system DTCs nor speed sensor DTCs (brake control system DTC) are output A
CAN communication system DTCs are output B
Brake control system (speed sensor) DTC is output C



A

2.INSPECT BATTERY

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

REPAIR CIRCUIT INDICATED BY OUTPUT CODE (BRAKE CONTROL SYSTEM)

2.INSPECT BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C270074C28
2.406,0.094 2.813,0.354 0.406,0.26 1.938,1.927 2.24,1.927 2.24,1.927 2.333,1.177 true 1.677,1.854 2.021,2.052 0.344,0.198 10 false IG1 2.49,0.146 2.802,0.344 0.313,0.198 10 false F14 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Disconnect the F14 4WD ECU assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F14-3 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Turn the ignition switch off.


b.
C270074C29
2.396,0.104 2.802,0.365 0.406,0.26 2.167,1.917 2.417,1.917 2.417,1.917 2.583,1.167 true 1.833,1.833 2.177,2.031 0.344,0.198 10 false GND 2.49,0.146 2.802,0.344 0.313,0.198 10 false F14 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F14-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.RECONFIRM DTC
a.

Clear the DTCs.

Click hereDrivetrain>MF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Clear DTCs
50002 118

b.

Start the engine.


c.

Drive the vehicle, accelerate to a speed of 3 km/h (2 mph) or more for 60 seconds or more, and check if the same DTC is output.

Click hereDrivetrain>MF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Trouble Codes
50001 118
HINT:

Reinstall the sensor, connectors, etc. and restore the vehicle to its prior condition before rechecking DTCs.



Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

B