If a malfunction in the speed sensor signal circuit or acceleration sensor (airbag sensor assembly) circuit occurs, the 4WD ECU assembly will output this DTC.
The airbag sensor assembly has a built-in acceleration sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| C1296/96 | ABS Malfunction | When one of the following conditions is met:
·
Wheel speed sensor malfunction is received from the skid control ECU (brake actuator assembly) ·
Acceleration sensor (airbag sensor assembly) malfunction is received from skid control ECU (brake actuator assembly |
·
Brake control system ·
Skid control ECU (Brake actuator assembly) ·
Acceleration sensor (airbag sensor assembly) circuit ·
4WD ECU assembly |
DTC stored |
Check the condition of each related circuit connector before troubleshooting.
Clear the DTCs.
Click hereDrivetrain>MF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON again and check that no CAN communication system DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Drive the vehicle, accelerate to a speed of 20 km/h (12 mph) or more, and check if the speed sensor DTC (brake control system DTC) and acceleration sensor DTC are output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before repairing each corresponding sensor.
| Result | Proceed to |
|---|---|
| Neither CAN communication system DTCs nor brake control system DTCs (speed sensor or acceleration sensor DTC) are output | A |
| CAN communication system DTCs are output | B |
| Brake control system DTCs (speed sensor or acceleration sensor DTC) are output | C |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
C
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Four Wheel Drive / Data List.
Read the value displayed on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | No large fluctuations when driving at a constant speed. |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | No large fluctuations when driving at a constant speed. |
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | No large fluctuations when driving at a constant speed. |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph) |
Vehicle stopped: 0 km/h (0 mph) | No large fluctuations when driving at a constant speed. |
| Tester Display |
|---|
| FR Wheel Speed |
| FL Wheel Speed |
| RR Wheel Speed |
| RL Wheel Speed |
The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the following menus: Chassis / Four Wheel Drive / Data List.
Read the value displayed on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Forward and Rearward G | Forward and Rearward G | Min.: -25.10 m/s2
Max.: 24.90 m/s2 |
Approximately 0 +/-0.13 m/s2 while stationary | Changes in proportion with acceleration/deceleration. |
| Tester Display |
|---|
| Forward and Rearward G |
The acceleration sensor (airbag sensor assembly) output value is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Perform the sensor check in the Test Mode procedure.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
| Tester Display |
|---|
| Signal Check |
Check if speed sensor DTCs (brake control system DTC) are output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Speed sensor DTCs are not output | A |
| Speed sensor DTCs are output | B |
A
B