Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch signals and uses them to determine whether or not the brakes are applied.

The skid control ECU (brake actuator assembly) has a detection circuit that it uses to detect an open in the stop light input line.

If the skid control ECU (brake actuator assembly) detects an open in this circuit, it will store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1425 Open in Stop Light Switch Circuit When voltage at terminal +BS is 9.5 to 17.4 V, open circuit occurs between STP terminal circuits A and B for 0.3 seconds or more.
·

Wire harness or connector

·

Stop light switch assembly

·

Skid control ECU (brake actuator assembly)



WIRING DIAGRAM

C369639E01
6.104,3.177 6.563,3.375 0.458,0.198 10 false STP 5.823,3.042 6.198,3.354 0.375,0.313 10 false 35 6.104,2.25 6.563,2.448 0.458,0.198 10 false STP2 5.875,2.115 6.25,2.427 0.375,0.313 10 false 5 6.104,1.344 6.563,1.542 0.458,0.198 10 false STPO 5.813,1.177 6.271,1.375 0.458,0.198 10 false 26 4.385,4.177 5.74,4.448 1.354,0.271 10 false to Stop Light Circuit 3.469,1.333 3.927,1.531 0.458,0.198 10 false ACC 3.667,2.229 4.125,2.427 0.458,0.198 10 false L 3.479,3.167 3.927,3.438 0.448,0.271 10 false OUT 3.885,1.198 4.344,1.396 0.458,0.198 10 false 4 3.885,2.115 4.344,2.313 0.458,0.198 10 false 3 3.875,3 4.281,3.333 0.406,0.333 10 false 1 5.51,3.688 7.083,4.104 1.573,0.417 10 false Skid Control ECU (Brake Actuator Assembly) 5.531,3.51 5.906,3.823 0.375,0.313 10 false A86 2.271,3.854 4.083,4.146 1.813,0.292 10 false Stop Light Switch Assembly 2.281,3.688 2.656,4 0.375,0.313 10 false A87 2.49,1.698 2.948,1.896 0.458,0.198 10 false B 2.469,3.219 2.927,3.417 0.458,0.198 10 false GND 2.25,1.563 2.458,1.833 0.208,0.271 10 false 7 2.26,3.052 2.469,3.323 0.208,0.271 10 false 2 1.5,1.854 2.052,2.083 0.552,0.229 10 false STOP 2.323,0.26 3.146,0.521 0.823,0.26 10 false from Battery 1,4.396 2.813,4.688 1.813,0.292 10 false : Open Detection Area 1.438,1.573 1.646,1.844 0.208,0.271 10 false 1 1.833,1.573 2.042,1.844 0.208,0.271 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. On
Brake pedal released. Off



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

NG

5.INSPECT STOP LIGHT SWITCH ASSEMBLY
2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37

d.

Check that the stop light switch display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1425 is not output. A
DTC C1425 is output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

4.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C364228C16
1.479,0.104 1.906,0.375 0.427,0.271 2.708,1.823 2.208,1.313 true 1.573,0.156 2.031,0.354 0.458,0.198 10 false A86 2.635,1.854 3.094,2.052 0.458,0.198 10 false STP 0.177,0.177 0.635,0.375 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A86-35 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A86-35 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

5.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Check the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION

OK:

The stop light switch assembly is normal.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C364228C16
1.479,0.104 1.906,0.375 0.427,0.271 2.708,1.823 2.208,1.313 true 1.573,0.156 2.031,0.354 0.458,0.198 10 false A86 2.635,1.854 3.094,2.052 0.458,0.198 10 false STP 0.177,0.177 0.635,0.375 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A86-35 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A86-35 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

7.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

7.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Reconnect the A86 skid control ECU (brake actuator assembly) connector.


c.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Turn the ignition switch off.


e.

Start the engine.


f.

Depress the brake pedal several times to test the stop light circuit.


g.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1425 is not output. A
DTC C1425 is output. B


HINT:
·

If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake actuator assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL

·

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE





A

B

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)