Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  U0073  Control Module Communication Bus OFF  U0100  Lost Communication with ECM / PCM  U0124  Lost Communication with Lateral Acceleration Sensor Module  U0126  Lost Communication with Steering Angle Sensor Module  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the ECM, steering angle sensor and yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0073 Control Module Communication Bus OFF Any of the following is detected:
1.

A bus OFF state occurs once or more within 0.1 seconds, 10 times in succession. (Sent signals cannot be received.)

2.

When the +BS terminal voltage is between 10 and 17.4 V, a delay in receiving data from the yaw rate sensor and steering angle sensor continues for 1 second or more.

3.

When the +BS terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession within 60 seconds.

-

The condition that a delay in receiving data from the yaw rate sensor and steering angle sensor occurs more than once within 5 seconds.



CAN communication system
U0100 Lost Communication with ECM / PCM When the +BS terminal voltage is between 10 and 17.4 V, and the vehicle speed is 15 km/h (9 mph) or more, data cannot be received from the ECM for 2 seconds or more.
·

CAN communication system

·

Skid control ECU (brake actuator assembly)

·

ECM


U0124 Lost Communication with Lateral Acceleration Sensor Module Either of the following is detected:
1.

When the +BS terminal voltage is between 10 and 17.4 V, and the vehicle speed is 7 km/h or more, data from the acceleration sensor cannot be received for 1 second or more.

2.

When the +BS terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession within 60 seconds.

-

The condition that data from the acceleration sensor cannot be received occurs once or more within 5 seconds.



·

CAN communication system

·

Skid control ECU (brake actuator assembly)

·

Acceleration sensor (airbag sensor assembly)


U0126 Lost Communication with Steering Angle Sensor Module Either of the following is detected:
1.

When the +BS terminal voltage is between 10 and 17.4 V, data from the steering angle sensor cannot be received for 1 second or more.

2.

When the +BS terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.

-

The condition that data from the steering angle sensor cannot be received occurs once or more within 5 seconds.



·

CAN communication system

·

Skid control ECU (brake actuator assembly)

·

Steering angle sensor



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
EFI Communication Open ECM communication open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Yaw Rate Open Yaw rate sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Deceleration Open Acceleration sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Steering Open Steering angle sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
EFI Communication Open
Yaw Rate Open
Deceleration Open
Steering Open
50003 105 204,205,206,207
Result:
Result Proceed to
There is a constant interruption. (Error is displayed without interruption.) A
There are no momentary interruptions. B
There are momentary interruptions. (Error is displayed intermittently.) C


HINT:

Perform the above inspection before disconnecting any sensors or connectors.




A

2.CHECK IF EACH CONNECTOR IS SECURELY CONNECTED (ECM, SENSOR)

B

3.RECONFIRM DTC

C

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK IF EACH CONNECTOR IS SECURELY CONNECTED (ECM, SENSOR)
a.

Turn the ignition switch off.


b.

Check if each sensor or ECM connector is securely connected.

OK:

Each connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

CONNECT CONNECTOR TO EACH SENSOR OR ECM CORRECTLY

3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Record the output DTCs (for VSC system and/or CAN communication system).

for VSC system: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

for CAN communication system: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

If CAN communication system DTCs and related sensor DTCs are output simultaneously, troubleshoot the DTCs (for VSC system) after the CAN communication system returns to normal.



Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B
CAN communication system DTCs are output. C



A

B

C

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Turn the ignition switch off.


b.

Repair or replace the harness or connector.


c.

Check for any momentary interruptions between the skid control ECU (brake actuator assembly) and each sensor or ECM.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 15 km/h (9 mph) or more and turn the steering wheel to the right and left.


f.

Check that no CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


g.

If VSC system DTCs are output, record them.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B
CAN communication system DTCs are output. C


HINT:

The CAN communication system must be normal when performing troubleshooting for sensor DTCs (for VSC system).




A

END

B

C