Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the ABS warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.

·

There is an open in the harness between the combination meter assembly and the skid control ECU (brake actuator assembly).

·

The ABS is defective.


HINT:

In some cases, the GTS cannot be used when the skid control ECU (brake actuator assembly) is abnormal.


WIRING DIAGRAM

C274777E94
0.865,1.25 1.271,1.448 0.406,0.198 10 false CANL 0.865,2.292 1.271,2.49 0.406,0.198 10 false CANH 1.344,2.094 1.583,2.323 0.24,0.229 10 false 28 1.333,1.052 1.552,1.229 0.219,0.177 10 false 27 0.292,5.885 0.781,6.115 0.49,0.229 10 false F126 0.281,6.042 1.479,6.396 1.198,0.354 10 false Combination Meter Assembly 2.792,6.406 4.552,6.583 1.76,0.177 10 false : CAN Communication Line 5.583,5.854 5.969,6.063 0.385,0.208 10 false A86 5.583,6.021 7.156,6.385 1.573,0.365 10 false Skid Control ECU (Brake Actuator Assembly) 5.833,1.083 6.052,1.26 0.219,0.177 10 false 10 6.115,1.25 6.563,1.438 0.448,0.188 10 false CANL 6.115,2.313 6.563,2.5 0.448,0.188 10 false CANH 6.135,3.333 6.583,3.521 0.448,0.188 10 false IG1 6.125,4.385 6.573,4.573 0.448,0.188 10 false GND1 5.833,2.125 6.052,2.302 0.219,0.177 10 false 22 5.833,3.198 6.115,3.479 0.281,0.281 10 false 12 5.844,4.24 6.042,4.479 0.198,0.24 10 false 25 1.938,3.333 3.333,3.531 1.396,0.198 10 false from IG1 NO. 3 Relay 4.385,3.5 5.313,3.688 0.927,0.188 10 false IG1 NO. 2 4.427,3.219 4.583,3.417 0.156,0.198 10 false 1 4.823,3.219 4.979,3.417 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Battery Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C364228C22
1.479,0.104 1.906,0.375 0.427,0.271 0.542,1.833 0.656,1.229 true 2.958,1.833 2.458,0.938 true 1.573,0.156 2.031,0.354 0.458,0.198 10 false A86 0.385,1.875 0.844,2.073 0.458,0.198 10 false GND1 2.844,1.865 3.302,2.063 0.458,0.198 10 false IG1 0.219,0.167 0.677,0.365 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the A86 skid control ECU (brake actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A86-12 (IG1) - Body ground Ignition switch ON 11 to 14 V
A86-12 (IG1) - A86-25 (GND1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


C364228C15
1.479,0.104 1.906,0.375 0.427,0.271 0.542,1.833 0.656,1.229 true 1.583,0.156 2.042,0.354 0.458,0.198 10 false A86 0.385,1.875 0.844,2.073 0.458,0.198 10 false GND1 0.219,0.167 0.677,0.365 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A86-25 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (ABS WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.READ VALUE USING GTS (ABS WARNING LIGHT)
a.

Reconnect the A86 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light ON or OFF ON: Warning light on
OFF: Warning light off
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
ABS Warning Light
50003 105 51

e.

Check the GTS display condition of the ABS warning light.

Result:
Result Proceed to
Display of the Data List remains ON. A
Display of the Data List remains OFF. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B