Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  VSC OFF Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, the TRC OFF message will be displayed on the multi-information display and the VSC OFF indicator light will come on.

WIRING DIAGRAM

C369734E02
5.969,0.927 6.583,1.125 0.615,0.198 10 false CANL 5.969,1.729 6.583,1.927 0.615,0.198 10 false CANH 5.677,0.729 6.292,0.927 0.615,0.198 10 false 10 5.688,1.542 6.302,1.74 0.615,0.198 10 false 22 5.969,2.875 6.583,3.198 0.615,0.323 10 false CSW 5.698,2.729 6.313,2.927 0.615,0.198 10 false 33 3.885,3.438 5.99,3.802 2.104,0.365 10 false VSC OFF Switch 3.896,3.271 4.51,3.469 0.615,0.198 10 false F40 3.99,3 4.604,3.198 0.615,0.198 10 false E 4.646,3 5.26,3.198 0.615,0.198 10 false + 4.854,2.74 5.469,2.938 0.615,0.198 10 false 6 3.771,2.75 4.375,3.031 0.604,0.281 10 false 3 2.938,4.333 5.042,4.698 2.104,0.365 10 false : CAN Communication Line 0.146,3.927 0.76,4.125 0.615,0.198 10 false F126 0.135,4.104 2.208,4.396 2.073,0.292 10 false Combination Meter Assembly 0.906,0.927 1.521,1.125 0.615,0.198 10 false CANL 0.906,1.74 1.521,1.938 0.615,0.198 10 false CANH 5.521,4.073 7.115,4.563 1.594,0.49 10 false Skid Control ECU (Brake Actuator Assembly) 5.531,3.917 6.146,4.24 0.615,0.323 10 false A86 1.396,1.542 1.938,1.854 0.542,0.313 10 false 28 1.396,0.719 1.938,1.031 0.542,0.313 10 false 27

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (TRC/VSC OFF MODE)

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

3.READ VALUE USING GTS (TRC/VSC OFF MODE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/VSC off mode Normal, TRC OFF, Unknown or VSC OFF Normal: Normal mode
Unknown: Unspecified
TRC OFF: TRC off mode
VSC OFF: VSC off mode
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
TRC/VSC Off Mode
50003 105 282

d.

Check the indicator light and mode condition on the GTS changes according to VSC OFF switch operation.

Standard:
Switch Operation Mode Condition Display Multi-information Display (TRC OFF Message) VSC OFF Indicator Light
Not pressed Normal Not displayed Does not come on
Pressing the VSC OFF switch TRC OFF Displayed Does not come on
Pressing and holding the VSC OFF switch VSC OFF Displayed Comes on



Result:
Result Proceed to
Indicator light and mode condition display do not change. A
Mode condition display is normal, but indicator light does not change. B
Indicator light and mode condition display is normal. C



A

4.PERFORM ACTIVE TEST USING GTS (MULTI-INFORMATION DISPLAY (TRC OFF MESSAGE) AND VSC OFF INDICATOR LIGHT)

B

C

4.PERFORM ACTIVE TEST USING GTS (MULTI-INFORMATION DISPLAY (TRC OFF MESSAGE) AND VSC OFF INDICATOR LIGHT)
a.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
TRC(TRAC) OFF Indicator Light Multi-information display (TRC OFF message) Display (message) ON/OFF Can be observed on the combination meter assembly
VSC OFF Indicator Light VSC OFF indicator light Indicator light ON/OFF Can be observed on the combination meter assembly
Chassis > ABS/VSC/TRC > Active Test
Tester Display
TRC(TRAC) OFF Indicator Light
50004 105 78
Chassis > ABS/VSC/TRC > Active Test
Tester Display
VSC OFF Indicator Light
50004 105 79

b.

Check the multi-information display (TRC OFF message) and VSC OFF indicator light in the combination meter assembly turn on or off in accordance with GTS operation.

OK:

The multi-information display (TRC OFF message) and VSC OFF indicator light turn on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

5.INSPECT VSC OFF SWITCH

NG

7.INSPECT COMBINATION METER ASSEMBLY
5.INSPECT VSC OFF SWITCH
a.
C239020C04
1.885,2.042 2.479,2.875 true 1.521,2.052 0.948,2.875 true 0.323,0.313 0.969,0.656 0.646,0.344 10 *a 2.427,2.885 2.885,3.146 0.458,0.26 10 E 0.854,2.885 1.333,3.25 0.479,0.365 10 +
*a Component without harness connected
(VSC OFF Switch)


Turn the ignition switch off.


b.

Disconnect the F40 VSC OFF switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (+) - 3 (E) Switch pushed Below 1 Ω
6 (+) - 3 (E) Switch not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)

NG

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)
a.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A86-33 (CSW) - F40-6 (+) Always Below 1 Ω
A86-33 (CSW) or F40-6 (+) - Body ground Always 10 kΩ or higher
F40-3 (E) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Perform an Active Test of the combination meter assembly using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display 1
50004 122 7
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. VSC OFF
50004 122 94

c.

Check the combination meter assembly.

OK:

The multi-information display and VSC OFF indicator light turn on or off in accordance with GTS operation.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG