Home › Engine / Hybrid System › 2GR-FKS (INTAKE / EXHAUST) › EXHAUST PIPE › from 2016.11
RM3160E _51 Engine / Hybrid System _060160 2GR-FKS INTAKE / EXHAUST _0299816 EXHAUST PIPE A

2GR-FKS INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 89465 1.INSTALL HEATED OXYGEN SENSOR (for Bank 2)

Hide 17410 2.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Install a new gasket to the front exhaust pipe assembly.


b.

Install the front exhaust pipe assembly to the exhaust manifold assembly LH (TWC: Front Catalyst) with the 2 nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


c.

Connect the heated oxygen sensor (for Bank 2) connector.


d.

Engage the 2 wire harnesses clamps.


Hide 17584B 3.INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Lower Side)

a.

Install the No. 1 exhaust pipe support bracket (for Lower Side) with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 89465 4.INSTALL HEATED OXYGEN SENSOR (for Bank 1)

HINT:

Perform "Inspection After Repairs" after replacing the heated oxygen sensor.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A369390C01
1.875,1.656 1.479,1.656 1.479,1.656 1.115,1.26 true 1.698,0.438 1.875,0.625 0.177,0.188 10 true *a 1.896,1.583 2.26,1.781 0.365,0.198 10 false SST
*a Torque Wrench Fulcrum Length


Using SST, install the heated oxygen sensor (for Bank 1) to the front No. 3 exhaust pipe sub-assembly.

SST
09224-00012  

Torque:
Specified tightening torque : 44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

If the heated oxygen sensor has been struck or dropped, replace it.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

37.7 N*m (384 kgf*cm, 28 ft.*lbf)




b.
A376731C01
1.479,1.219 1.615,1.219 1.615,1.219 1.854,0.927 true 1.323,1.146 1.635,1.344 0.313,0.198 10 false *1 1.313,0.615 1.625,0.813 0.313,0.198 10 false *a 1.99,0.167 2.302,0.365 0.313,0.198 10 false *b
*1 Wire Harness Clamp Bracket
*a Left of Vehicle
*b 180°


Install the wire harness clamp bracket to the heated oxygen sensor (for Bank 1).

HINT:

Make sure the direction of the wire harness clamp bracket is as shown in the illustration.



Hide 17403 5.INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

a.

Install 2 new gaskets to the front No. 3 exhaust pipe sub-assembly.


b.

Install the front No. 3 exhaust pipe sub-assembly to the front exhaust pipe assembly and exhaust manifold (TWC: Front Catalyst) with the 2 bolts and 2 nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


c.

Connect the heated oxygen sensor (for Bank 1) connector.


d.

Engage the 3 wire harness clamps.


Hide 17420 6.INSTALL CENTER EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.
A128853

Using a vernier caliper, measure the free length of the 2 compression springs.

Standard Length 43.0 mm (1.69 in.)
Minimum Free Length 41.5 mm (1.63 in.)

If the free length is less than minimum, replace the compression spring.


b.

Temporarily install a new gasket to the front No. 3 exhaust pipe sub-assembly.


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Front No. 3 Exhaust Pipe Sub-assembly
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the front No. 3 exhaust pipe sub-assembly.

NOTICE:
·

Be careful with the installation direction of the gasket.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipes when connecting them.




d.

Connect the center exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust pipe support.


e.

Install the center exhaust pipe assembly (TWC: Rear Catalyst) to the front No. 3 exhaust pipe sub-assembly with the 2 bolts and 2 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258966C28
1.365,0.938 1.094,0.406 1.094,0.406 0.896,0.406 false 1.333,1.167 1.125,1.51 1.125,1.51 0.938,1.51 false 2.24,0.948 2.625,0.448 2.625,0.448 2.823,0.448 true 0.719,0.323 0.875,0.469 0.156,0.146 10 false *1 0.76,1.427 0.917,1.573 0.156,0.146 10 false *2 2.844,0.365 3,0.51 0.156,0.146 10 false *3 0.625,1.74 0.823,2 0.198,0.26 10 false *a
*1 Center Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Front No. 3 Exhaust Pipe Sub-assembly
*3 Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the center exhaust pipe assembly (TWC: Rear Catalyst) and front No. 3 exhaust pipe sub-assembly is consistent front-to-rear and left-to-right.



Hide 17581C 7.INSTALL NO. 3 EXHAUST PIPE DAMPER

a.

Install the No. 3 exhaust pipe damper to the tail exhaust pipe assembly with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 17430 8.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.

Install a new gasket to the center exhaust pipe assembly (TWC: Rear Catalyst).


b.

Connect the tail exhaust pipe assembly to the 4 exhaust pipe supports.


c.

Install the tail exhaust pipe assembly to the center exhaust pipe assembly (TWC: Rear Catalyst) with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 9.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

a.

Perform Inspection After Repair after repairing an exhaust gas leak.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Hide 51442 11.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51441 12.INSTALL NO. 1 ENGINE UNDER COVER