Home › Engine / Hybrid System › 2GR-FKS (INTAKE / EXHAUST) › EXHAUST MANIFOLD › from 2016.11
RM3160E _51 Engine / Hybrid System _060160 2GR-FKS INTAKE / EXHAUST _0299815 EXHAUST MANIFOLD A

2GR-FKS INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 1.INSTALL STUD BOLT

HINT:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A370453

Using an E8 "TORX" socket wrench, install the 2 stud bolts to the exhaust manifold (TWC: Front Catalyst).

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


b.
A370454

Using an E8 "TORX" socket wrench, install the 2 stud bolts to the exhaust manifold assembly LH (TWC: Front Catalyst).

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 17173 2.INSTALL EXHAUST MANIFOLD TO HEAD GASKET (for Bank 2)

a.

Install a new exhaust manifold to head gasket (for Bank 2) to the cylinder head sub-assembly.


Hide 17150 3.INSTALL EXHAUST MANIFOLD ASSEMBLY LH (TWC: Front Catalyst)

a.

Temporarily install the exhaust manifold assembly LH (TWC: Front Catalyst) with the 4 nuts.


b.

Temporarily install the No. 2 manifold stay to the exhaust manifold assembly LH (TWC: Front Catalyst) and cylinder block sub-assembly with the bolt and nut.


c.
A395763N01
0.688,0.198 0.885,0.375 0.198,0.177 10 true 4 1.917,0.156 2.135,0.354 0.219,0.198 10 true 1 0.583,1.531 0.771,1.729 0.188,0.198 10 true 2 2,1.531 2.188,1.729 0.188,0.198 10 true 3

Using a 12 mm deep socket wrench, tighten the 4 nuts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.
A395762C02
1.99,0.375 2.219,0.583 0.229,0.208 10 true 1 2.135,1.51 2.365,1.719 0.229,0.208 10 true 2
V100135

Bolt
V100136

Nut


Tighten the bolt and nut in the order shown in the illustration.

Torque:
Nut : 35 N*m (357 kgf*cm, 26 ft.*lbf)
Bolt : 34 N*m (347 kgf*cm, 25 ft.*lbf)


Hide 17168 4.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A395761N01
0.688,0.073 0.885,0.281 0.198,0.208 10 true 1 2.333,0.979 2.531,1.188 0.198,0.208 10 true 2 0.115,0.542 0.313,0.75 0.198,0.208 10 true 3

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold assembly LH (TWC: Front Catalyst) with the 3 bolts in the order shown in the illustration.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 89467B 5.INSTALL AIR FUEL RATIO SENSOR (for Bank 2)

Hide 11209 6.INSTALL V-BANK COVER SUB-ASSEMBLY

Hide 17410 7.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 17584B 8.INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Lower Side)

Hide 89467B 9.INSTALL AIR FUEL RATIO SENSOR (for Bank 1)

Hide 17173 10.INSTALL EXHAUST MANIFOLD TO HEAD GASKET (for Bank 1)

a.

Install a new exhaust manifold to head gasket (for Bank 1) to the cylinder head sub-assembly RH.


Hide 17141 11.INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)

a.

Temporarily install the exhaust manifold (TWC: Front Catalyst) with the 4 nuts.


b.

Temporarily install the manifold stay to the exhaust manifold (TWC: Front Catalyst) and rear engine mounting bracket with the bolt and nut.


c.
A370440N01
2.708,0.656 2.865,0.854 0.156,0.198 10 true 1 2.063,1.885 2.219,2.083 0.156,0.198 10 true 2 2.854,1.708 3.01,1.906 0.156,0.198 10 true 3 2.167,0.49 2.323,0.688 0.156,0.198 10 true 4

Using a 12 mm deep socket wrench, tighten the 4 nuts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.
A370439C03
0.823,1.698 1.021,1.927 0.198,0.229 10 true 1 1.354,0.271 1.552,0.458 0.198,0.188 10 true 2
V100135

Bolt
V100136

Nut


Tighten the bolt and nut in the order shown in the illustration.

Torque:
Bolt : 34 N*m (347 kgf*cm, 25 ft.*lbf)
Nut : 35 N*m (357 kgf*cm, 26 ft.*lbf)


e.

Engage the 3 wire harness clamps.


f.

Connect the air fuel ratio sensor connector.


Hide 17403 12.INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the 2 compression springs.

Standard Length 43.0 mm (1.69 in.)
Minimum Free Length 41.5 mm (1.63 in.)

If the free length is less than minimum, replace the compression spring.


b.

Temporarily install a new gasket to the front No. 3 exhaust pipe sub-assembly (center exhaust pipe assembly (TWC: Rear Catalyst) side).


c.
A181728C68
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.365 false 1.458,0.667 1.813,0.667 1.813,0.667 1.813,1.125 false 1.292,0.573 1.583,0.792 0.292,0.219 10 false *1 2.854,1.49 3.135,1.698 0.281,0.208 10 false *a 1.448,3.104 1.771,3.344 0.323,0.24 10 false *2
*1 Front No. 3 Exhaust Pipe Sub-assembly
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the front No. 3 exhaust pipe sub-assembly.

NOTICE:
·

Be careful with the installation direction of the gasket.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipes when connecting them.




d.

Install 2 new gaskets to the front No. 3 exhaust pipe sub-assembly.


e.

Temporarily install the front No. 3 exhaust pipe sub-assembly with the 4 bolts, 2 nuts and 2 compression springs.


f.

Tighten the 2 bolts and 2 nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


g.

Tighten the 2 bolts and 2 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258966C27
1.365,0.938 1.094,0.406 1.094,0.406 0.896,0.406 false 1.333,1.167 1.125,1.51 1.125,1.51 0.938,1.51 false 2.24,0.948 2.625,0.448 2.625,0.448 2.823,0.448 true 0.708,0.354 1.021,0.656 0.313,0.302 10 false *1 0.74,1.448 0.99,1.698 0.25,0.25 10 false *2 2.875,0.385 3.219,0.677 0.344,0.292 10 false *3 0.625,1.74 1,2.01 0.375,0.271 10 false *a
*1 Center Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Front No. 3 Exhaust Pipe Sub-assembly
*3 Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the center exhaust pipe assembly (TWC: Rear Catalyst) and front No. 3 exhaust pipe sub-assembly is consistent front-to-rear and left-to-right.



h.

Connect the heated oxygen sensor (for Bank 1) connector.


i.

Engage the 3 wire harness clamps.


Hide 58166 14.INSTALL FRONT FLOOR COVER LH

a.
A315837C01
1.521,1.313 1.74,1.542 0.219,0.229 10 true A 1.552,0.635 1.771,0.865 0.219,0.229 10 true B 0.781,0.542 1,0.771 0.219,0.229 10 true B
V100135

Bolt
V100136

Screw


Install the front floor cover LH with the 2 clips (B).


b.

Install the clip (A), 2 screws and 4 bolts to the front floor cover LH.


Hide 51442 15.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51441 16.INSTALL NO. 1 ENGINE UNDER COVER