Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE FLUID › from 2016.11
RM3160E _52 Drivetrain _019727 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0107352 AUTOMATIC TRANSAXLE FLUID N

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE FLUID  ADJUSTMENT  


PROCEDURE

Hide 1. PRECAUTIONS AND WORK DESCRIPTION

a.

The U760E automatic transaxle assembly does not have an oil filler tube and oil level gauge. When adding fluid, add fluid through the refill hole on the rear transaxle cover sub-assembly. The fluid level can be adjusted by draining excess fluid (allowing excess fluid to overflow) through the No. 1 transmission oil filler tube of the automatic transaxle oil pan sub-assembly.

HINT:

"Overflow" indicates the condition under which fluid comes out of the overflow plug hole.



b.

Before adjusting the fluid level, add the specified amount of fluid when the engine is cold and warm up the engine to circulate the fluid in the automatic transaxle assembly. Ensure that the fluid temperature is as specified and the engine is idling.

C242969E03
2.844,2.344 2.844,2.229 2.844,2.229 1.948,2.104 false 6.073,2.594 6.073,2.5 6.073,2.5 5.677,2.323 false 1.302,3.219 4.365,3.406 3.063,0.188 12 false 3. ADJUST FLUID TEMPERATURE 0.323,5.667 2.271,6.01 1.948,0.344 12 false 4. ADJUST FLUID LEVEL 0.094,0.042 2.25,0.24 2.156,0.198 12 false Fluid Filling Procedure: 0.5,0.406 3.01,0.615 2.51,0.208 12 false 1. PERFORM INITIAL FILLING 4.01,0.406 7.146,0.615 3.135,0.208 12 false 2. ADD SPECIFIED AMOUNT OF FLUID 0.51,0.771 3.406,1.083 2.896,0.313 10 false Add fluid to the transaxle oil pan sub-assembly to the specified level. 4.073,0.771 6.75,1.167 2.677,0.396 10 false Add the correct amount of fluid specified for the operation that was performed. 5.688,2.625 6.615,2.948 0.927,0.323 10 false Overflow Plug 4.427,7.792 5.625,8.396 1.198,0.604 10 false Add fluid until fluid comes out of the overflow plug hole. 0.438,2.365 1.635,2.948 1.198,0.583 10 false Add fluid until fluid comes out of the overflow plug hole. 0.25,7.781 2.021,8.406 1.771,0.625 10 false Keep the overflow plug open until the fluid flow slows and only drips come out. 0.333,6.031 2.74,6.677 2.406,0.646 10 false Drain excess fluid at the specified fluid temperature. 4.208,6.031 6.656,6.417 2.448,0.385 10 false If no fluid comes out, add fluid until fluid comes out of the overflow plug hole. 1.281,3.677 6.802,4.063 5.521,0.385 10 false Start the engine to circulate the fluid. Activate fluid temperature detection mode and engine idle speed control mode, and adjust the fluid temperature to the specified level. 2.125,2.365 3.375,2.729 1.25,0.365 10 false No. 1 Transmission Oil Filler Tube 6.51,1.698 7.125,2.323 0.615,0.625 10 false Specified Amount of Fluid


c.

The U760E automatic transaxle assembly requires Toyota Genuine ATF WS.


d.

The adjustment should be performed according to the procedures and notes.


Hide 2. WORK FLOW

a.

The adjustment should be performed according to the procedure referenced in the work flow below.

C197806E11
0.083,0.083 1.479,0.396 1.396,0.313 10 Work Flow: 3.375,0.188 4.031,0.552 0.656,0.365 10 START 1.365,1.406 2.667,1.813 1.302,0.406 10 Perform initial filling 1.167,3.51 6.01,3.917 4.844,0.406 10 Activate fluid temperature detection mode and engine idle speed control mode 3.948,1.406 6.531,1.813 2.583,0.406 10 Not necessary to perform initial filling 2.677,2.354 5.073,2.76 2.396,0.406 10 Add specified amount of fluid 3.052,5.719 4.177,6.125 1.125,0.406 10 Drain excess fluid 3.021,7.615 4.26,8.021 1.24,0.406 10 Finish up operation 3.448,8.354 3.792,8.76 0.344,0.406 10 END 5.823,6.865 6.479,7.271 0.656,0.406 10 Add fluid 3.344,6.854 3.948,7.26 0.604,0.406 10 Overflow 2.49,4.979 4.677,5.385 2.188,0.406 10 Fluid level adjustment temperature 5.438,4.563 6.896,5.188 1.458,0.625 10 Above fluid level adjustment temperature 5.552,6.156 6.74,6.521 1.188,0.365 10 No fluid comes out 0.188,7.479 1.76,7.802 1.573,0.323 10 Step 5. REBUILD WORK 0.188,0.677 2.833,1 2.646,0.323 10 Step 1. PERFORM INITIAL FILLING 0.188,5.563 2.354,5.885 2.167,0.323 10 Step 4. ADJUST FLUID LEVEL 0.188,3.115 3.063,3.438 2.875,0.323 10 Step 3. ADJUST FLUID TEMPERATURE 0.188,2.229 2.344,2.583 2.156,0.354 10 Step 2. ADD SPECIFIED AMOUNT OF FLUID 2.854,4.24 4.469,4.448 1.615,0.208 10 Idling (Warm up the fluid)


Hide 3. PREPARATION WORK

a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/- 1°).



b.

Remove the No. 1 engine under cover.

Click hereEngine / Hybrid System>1AR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


c.

d.

Remove the front fender apron seal LH.

Click hereEngine / Hybrid System>1AR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


Hide 4. PERFORM INITIAL FILLING

NOTICE:

If the automatic transaxle assembly is hot (ATF temperature is high), wait until the fluid temperature becomes the same as the ambient temperature before starting the following procedure. (Recommended ATF temperature: around 20°C (68°F))


a.
C201682

Remove the refill plug and gasket from the automatic transaxle assembly.

NOTICE:

After performing any of the following operations, it is not necessary to perform the initial filling procedure. Proceed to the Add Specified Amount of Fluid procedure.


Operations that do not require initial filling
·

Disconnection of the oil cooler tube or oil cooler hose

·

Repair of fluid leak due to a loose case plug, or a faulty plug gasket or O-ring

·

Replace of the automatic transaxle assembly




b.
C239660

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle oil pan sub-assembly.

NOTICE:
·

If ATF comes out after removing the overflow plug, wait until the fluid flow slows and only drips come out.

·

If ATF comes out, it is not necessary to perform the initial filling procedure. After checking the tightening torque of the No. 1 transmission oil filler tube, temporarily install the overflow plug.




c.
C201684C19
1.208,2.677 0.833,2.677 false 0.604,3.927 0.417,3.927 0.417,3.927 0.708,3.125 false 1.208,3.219 0.833,3.219 false 1.219,2.594 1.375,2.76 0.156,0.167 10 false *1 1.219,3.135 1.385,3.302 0.167,0.167 10 false *a 0.656,3.844 0.833,4.031 0.177,0.188 10 false *b
*1 No. 1 Transmission Oil Filler Tube
*a Hexagon Socket Wrench
*b Overflow Plug Hole


Using a 6 mm hexagon socket wrench, check that the No. 1 transmission oil filler tube is tightened to the specified torque.

Torque:
0.8 N*m (8 kgf*cm, 7 in.*lbf)

NOTICE:

If the No. 1 transmission oil filler tube is not tightened to the specified torque, the amount of fluid cannot be precisely adjusted.


HINT:

To check the torque of the No. 1 transmission oil filler tube, insert the hexagon socket wrench into the overflow plug hole.



d.

Perform initial filling.

i.
C298993

Fill the automatic transaxle assembly through the refill hole until fluid begins to come out of the overflow plug hole.

NOTICE:

Use Toyota Genuine ATF WS.




e.
C298994

Wait until the fluid flow slows and only drips come out.


f.
C298991

Temporarily install the gasket and overflow plug to the automatic transaxle oil pan sub-assembly.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the fluid level.



Hide 5.ADD SPECIFIED AMOUNT OF FLUID

a.

Fill the automatic transaxle assembly with the correct amount of fluid as listed in the table below.

NOTICE:

The refill amount differs depending on the operation that was performed.


Reference Capacity:
Performed Repair Fill Amount
Automatic transaxle assembly replacement (with a new torque converter assembly) 5.1 liters (5.4 US qts, 4.5 Imp.qts)
Automatic transaxle assembly replacement (when reusing the torque converter assembly) 3.5 liters (3.7 US qts, 3.1 Imp.qts)
Removal and installation of the torque converter assembly 3.4 liters (3.6 US qts, 3.0 Imp.qts)
Removal and installation of the transmission valve body assembly 3.2 liters (3.4 US qts, 2.8 Imp.qts)
Removal and installation of the automatic transaxle oil pan sub-assembly 2.7 liters (2.9 US qts, 2.4 Imp.qts)
Removal and installation of a front drive shaft assembly 2.7 liters (2.9 US qts, 2.4 Imp.qts)
Removal and installation of the front drive shaft oil seal LH or front drive shaft oil seal RH 2.7 liters (2.9 US qts, 2.4 Imp.qts)
Disconnection of a oil cooler tube or oil cooler hose 0.5 liters (0.5 US qts, 0.4 Imp.qts)
Repair of fluid leak due to a loose case plug, or a faulty plug gasket or O-ring 0.5 liters (0.5 US qts, 0.4 Imp.qts)



b.
C201682

Temporarily install the gasket and refill plug to avoid fluid spillage.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.



c.

Lower the vehicle.


Hide 6.ADJUST FLUID TEMPERATURE (when Using the GTS)

HINT:

The actual ATF temperature can be checked on the Data List using the GTS.


a.

Connect the GTS to the DLC3 with the ignition switch off.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fans and audio system are off.



c.

Enter the following menus: Powertrain / Engine / Active Test / Connect the TC and TE1.

Powertrain > Engine > Active Test
Tester Display
Connect the TC and TE1
50004 234 13

d.

Select the Active Test item: Connect the TC and TE1 / ON.


e.

Select the Data List menu: A/T Oil Temperature 1.

Powertrain > Engine > Data List
Tester Display
A/T Oil Temperature 1
50003 234 406

f.

Check the ATF temperature.

NOTICE:
·

If the fluid temperature is below 45°C (113°F), proceed to the next step. (Recommended ATF temperature: 35°C (95°F) or less)

·

If the fluid temperature is 45°C (113°F) or more, turn the ignition switch to off and wait until the fluid temperature drops below 45°C (113°F).




g.

Depress and hold the brake pedal.


h.

Start the engine.


i.

Slowly move the shift lever from P to D, and then back to P.

HINT:

Slowly move the shift lever to circulate the fluid through each part of the automatic transaxle assembly.



j.
C363775

While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of less than 1.5 seconds for 6 seconds or more.

NOTICE:

Do not pause for more than 1.5 seconds.


HINT:

Performing this operation will cause the vehicle to enter fluid temperature detection mode.



k.

Check that the D shift indicator comes on for 2 seconds.

HINT:
·

When fluid temperature detection mode is activated, the D shift indicator on the combination meter comes on for 2 seconds.

·

If the D shift indicator does not come on for 2 seconds, return to the first step and perform the procedure again.




l.

Move the shift lever from N to P.


m.

Release the brake pedal.


n.

Select the Active Test item: Connect the TC and TE1 / OFF.

NOTICE:

Be sure that terminals TC and TE1 are not connected. If the terminals are connected, the fluid level cannot be precisely adjusted due to fluctuations in engine speed.


HINT:
·

Disconnecting terminals TC and TE1 activates engine idle speed control mode.

·

In engine idle speed control mode, engine idle speed control starts when the fluid temperature is 35°C (95°F) or more and the engine speed is maintained at approximately 800 rpm.

·

Even after terminals TC and TE1 are disconnected, fluid temperature detection mode is active until the ignition switch is turned off.




o.
C363776C01
0.521,0.167 0.833,0.323 0.313,0.156 10 false *a 1.656,0.167 1.969,0.344 0.313,0.177 10 false *b 2.74,0.146 3.063,0.427 0.323,0.281 10 false *c
*a Turned Off
*b Turned On
*c Blinking


Warm up the engine with the engine idling until the fluid temperature reaches the fluid level adjustment temperature (35 to 45°C (95 to 113°F)).

Below Fluid Level Adjustment Temperature Fluid Level Adjustment Temperature Above Fluid Level Adjustment Temperature
35°C or less
(95°F or less)
35 to 45°C
(95 to 113°F)
45°C or more
(113°F or more)

NOTICE:
·

If the fluid temperature is within the fluid level adjustment temperature range, immediately proceed to the Adjust Fluid Level procedure.

·

If the fluid temperature is 45°C (113°F) or more, stop the engine and wait until the fluid temperature drops to 35°C (95°F) or less. Then perform the Adjust Fluid Temperature procedure again from the beginning.



HINT:

In fluid temperature detection mode, the D shift indicator comes on, goes off, or blinks depending on the fluid temperature.


D Shift Indicator
Below Fluid Level Adjustment Temperature
(35°C or less)
(95°F or less)
Fluid Level Adjustment Temperature
(35 to 45°C)
(95 to 113°F)
Above Fluid Level Adjustment Temperature
(45°C or more)
(113°F or more)
OFF ON Blinks


Hide 7.ADJUST FLUID TEMPERATURE (when Not Using the GTS)

a.
C101492C37
1.938,1.51 2.198,1.885 true 1.385,0.302 1.667,0.75 true 0.969,0.802 1.052,0.927 0.083,0.125 8 false 1 1.198,0.802 1.281,0.927 0.083,0.125 8 false 2 1.438,0.792 1.521,0.917 0.083,0.125 8 false 3 1.667,0.792 1.75,0.917 0.083,0.125 8 false 4 1.917,0.792 2,0.917 0.083,0.125 8 false 5 2.146,0.792 2.229,0.917 0.083,0.125 8 false 6 2.365,0.802 2.448,0.927 0.083,0.125 8 false 7 2.615,0.802 2.698,0.927 0.083,0.125 8 false 8 0.979,1.292 1.063,1.417 0.083,0.125 8 false 9 1.167,1.292 1.313,1.417 0.146,0.125 8 false 10 1.396,1.292 1.542,1.417 0.146,0.125 8 false 11 1.635,1.292 1.781,1.417 0.146,0.125 8 false 12 1.875,1.292 2.021,1.417 0.146,0.125 8 false 13 2.125,1.292 2.271,1.417 0.146,0.125 8 false 14 2.333,1.292 2.479,1.417 0.146,0.125 8 false 15 2.573,1.292 2.719,1.417 0.146,0.125 8 false 16 1.135,0.198 1.438,0.365 0.302,0.167 10 false CG 2.24,1.813 2.427,1.979 0.188,0.167 10 false TC 0.198,0.125 0.75,0.406 0.552,0.281 10 false *1
*1 DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 with the ignition switch off.

SST
09843-18040  


b.

Depress and hold the brake pedal.


c.

Start the engine.

NOTICE:

To reduce load, make sure that all electrical systems, such as the air conditioning, lighting system, electric fans and audio system, are off.


HINT:

The indicator lights on the combination meter blink to indicate the DTC output when terminals TC and CG are connected.



d.

Slowly move the shift lever from P to D, and then back to P.

HINT:

Slowly move the shift lever to circulate the fluid through each part of the transaxle.



e.
C363775

While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of less than 1.5 seconds for 6 seconds or more.

NOTICE:

Do not pause for more than 1.5 seconds.


HINT:

Performing this operation will cause the vehicle to enter fluid temperature detection mode.



f.

Check that the D shift indicator comes on for 2 seconds.

HINT:
·

When fluid temperature detection mode is activated, the D shift indicator on the combination meter comes on for 2 seconds.

·

If the D shift indicator does not come on for 2 seconds, return to the first step and perform the procedure again.




g.

Move the shift lever from N to P.


h.

Release the brake pedal.


i.
C101492C37
1.938,1.51 2.198,1.885 true 1.385,0.302 1.667,0.75 true 0.969,0.802 1.052,0.927 0.083,0.125 8 false 1 1.198,0.802 1.281,0.927 0.083,0.125 8 false 2 1.438,0.792 1.521,0.917 0.083,0.125 8 false 3 1.667,0.792 1.75,0.917 0.083,0.125 8 false 4 1.917,0.792 2,0.917 0.083,0.125 8 false 5 2.146,0.792 2.229,0.917 0.083,0.125 8 false 6 2.365,0.802 2.448,0.927 0.083,0.125 8 false 7 2.615,0.802 2.698,0.927 0.083,0.125 8 false 8 0.979,1.292 1.063,1.417 0.083,0.125 8 false 9 1.167,1.292 1.313,1.417 0.146,0.125 8 false 10 1.396,1.292 1.542,1.417 0.146,0.125 8 false 11 1.635,1.292 1.781,1.417 0.146,0.125 8 false 12 1.875,1.292 2.021,1.417 0.146,0.125 8 false 13 2.125,1.292 2.271,1.417 0.146,0.125 8 false 14 2.333,1.292 2.479,1.417 0.146,0.125 8 false 15 2.573,1.292 2.719,1.417 0.146,0.125 8 false 16 1.135,0.198 1.438,0.365 0.302,0.167 10 false CG 2.24,1.813 2.427,1.979 0.188,0.167 10 false TC 0.198,0.125 0.75,0.406 0.552,0.281 10 false *1
*1 DLC3


Remove SST from terminals 13 (TC) and 4 (CG).

NOTICE:

Be sure that terminals TC and CG are not connected. If the terminals are connected, the fluid level cannot be precisely adjusted due to fluctuations in engine speed.


HINT:
·

Disconnecting terminals TC and CG activates engine idle speed control mode.

·

In engine idle speed control mode, engine idle speed control starts when the fluid temperature is 35°C (95°F) or more and the engine speed is maintained at approximately 800 rpm.

·

Even after terminals TC and CG are disconnected, fluid temperature detection mode is active until the ignition switch is turned off.




j.
C363776C01
0.521,0.167 0.833,0.323 0.313,0.156 10 false *a 1.656,0.167 1.969,0.344 0.313,0.177 10 false *b 2.74,0.146 3.063,0.427 0.323,0.281 10 false *c
*a Turned Off
*b Turned On
*c Blinking


Allow the engine to idle until the D shift indicator comes on again.

D Shift Indicator
Below Fluid Level Adjustment Temperature
(35°C or less)
(95°F or less)
Fluid Level Adjustment Temperature
(35 to 45°C)
(95 to 113°F)
Above Fluid Level Adjustment Temperature
(45°C or more)
(113°F or more)
OFF ON Blinks

NOTICE:
·

If the D shift indicator is on, immediately proceed to the Adjust Fluid Level procedure.

·

If the D shift indicator blinks, stop the engine and wait until the fluid temperature drops to 35°C (95°F) or less (the indicator goes off). Then perform the Adjust Fluid Temperature procedure again from the beginning.



HINT:
·

In fluid temperature detection mode, the D shift indicator comes on, goes off, or blinks depending on the fluid temperature.

·

The fluid filling procedure should be performed when the D shift indicator is on (the fluid temperature is within the fluid level adjustment temperature range).




Hide 8.ADJUST FLUID LEVEL

CAUTION:

Use caution while the engine is idling and the radiator fans are operating.


a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure the tilt angle from the front to rear of the vehicle is within +/- 1°).



b.

Adjust the fluid level.

i.
C298991

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle oil pan sub-assembly.

CAUTION:

Be careful as the fluid coming out of the overflow plug hole is hot.



ii.

Check the amount of fluid that comes out of the overflow plug hole.

NOTICE:

If only a small amount of fluid (approximately 1 cc) comes out of the overflow plug hole, then only fluid remaining in the No. 1 transmission oil filler tube has come out. This condition is not considered as overflow, so it is necessary to add fluid.



iii.
C298992

If the amount of fluid that comes out of the overflow plug hole is large, wait until the fluid flow slows and only drips come out.


iv.
C298993

If no fluid comes out of the overflow plug hole, remove the refill plug and gasket. Then add transaxle fluid through the refill hole until fluid comes out of the overflow plug hole. Wait until the fluid flow slows and only drips come out.

NOTICE:

Use Toyota Genuine ATF WS.



v.
C298994

Check that the fluid flow has slowed and only drips come out.

HINT:

The fluid flow will not completely stop because the fluid continues to expand as its temperature increases.




c.
C298991

Using a 6 mm hexagon socket wrench, install a new gasket and the overflow plug to the automatic transaxle oil pan sub-assembly.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


d.
C201682

Install a new gasket and the refill plug to the automatic transaxle assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


e.

Lower the vehicle.


f.

Turn the ignition switch off.

HINT:

Turning the ignition switch off ends fluid temperature detection mode.



g.

Disconnect the GTS from the DLC3 (for using the GTS).


Hide 9. REBUILD WORK

a.

Lift the vehicle.


b.

Clean each part.


c.

Check for fluid leaks.


d.

Install the front fender apron seal LH.

Click hereEngine / Hybrid System>1AR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION



f.

g.

Lower the vehicle.