Home › Engine / Hybrid System › 1AR-FE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2016.11
RM3160E _51 Engine / Hybrid System _019672 1AR-FE ENGINE MECHANICAL _0109594 ENGINE ASSEMBLY A

1AR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

CAUTION:

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 6.REMOVE FRONT WHEELS

Hide 7.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected .

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 51441 8.REMOVE NO. 1 ENGINE UNDER COVER

a.

Remove the 6 bolts, 8 screws, 3 clips and No. 1 engine under cover.


Hide 51442 9.REMOVE NO. 2 ENGINE UNDER COVER

a.

Remove the 2 bolts, 2 screws, clip and No. 2 engine under cover.


Hide 51454C 10.REMOVE FLOOR UNDER COVER LH

Hide 53876A 11.SEPARATE FRONT FENDER LINER LH

a.

Remove the 3 screws, 3 clips and separate the front fender liner LH.


Hide 53875A 12.SEPARATE FRONT FENDER LINER RH

a.

Remove the 2 screws, 3 clips and separate the front fender liner RH.


Hide 53737B 13.REMOVE FRONT FENDER APRON SEAL LH

a.
A171852

Remove the 2 bolts, clip and front fender apron seal LH.


Hide 53736 14.REMOVE FRONT FENDER APRON SEAL RH

a.
A171853

Remove the 2 bolts, clip and front fender apron seal RH.


Hide 18.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 19.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 53299D 20.REMOVE RADIATOR SIDE DEFLECTOR SEAL LH

Hide 53298E 21.REMOVE RADIATOR SIDE SEAL RH

Hide 53295E 22.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 12601B 23.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

a.
A316581

Lift the rear of the No. 1 engine cover sub-assembly to disengage it from the 2 pins.

NOTICE:

Attempting to disengage both front and rear pins at the same time may cause the No. 1 engine cover sub-assembly to break.



b.

Lift the front of the No. 1 engine cover sub-assembly to disengage it from the pin and remove it.


Hide 17750A 24.REMOVE INLET AIR CLEANER ASSEMBLY

a.
A315809

Remove the 2 bolts and inlet air cleaner assembly.


Hide 17705 25.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 26.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly.


Hide 17701 27.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A315811

Remove the 2 bolts and air cleaner case sub-assembly.


Hide 47220D 28.REMOVE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

Hide 47233 29.REMOVE RESERVOIR BRACKET

Hide 28800 30.REMOVE BATTERY

a.
A315820

Loosen the nut, and disconnect the cable from the positive (+) battery terminal.


b.

Loosen the nut, and remove the bolt and battery clamp.


c.

Remove the battery and battery tray.


Hide 16571C 31.DISCONNECT NO. 1 RADIATOR HOSE

a.
A283847

Remove the hose clamp to separate the air fuel ratio sensor wire from the No. 1 radiator hose.


b.

Slide the clip and disconnect the No. 1 radiator hose from the cylinder head sub-assembly.


Hide 16572D 32.DISCONNECT NO. 2 RADIATOR HOSE

a.
A255407

Slide the clip and disconnect the No. 2 radiator hose from the water inlet.


Hide 87245 33.DISCONNECT INLET HEATER WATER HOSE

a.
A269374

Slide the clip and disconnect the inlet heater water hose from the cylinder head sub-assembly.


Hide 87246 34.DISCONNECT OUTLET HEATER WATER HOSE

a.
A315817C01
2.948,1.531 2.948,1.281 false 2.875,1.01 2.854,0.479 2.854,0.479 2.729,0.479 false 0.729,1.813 0.917,1.813 0.917,1.813 1.156,1.615 true 2.552,0.406 2.865,0.604 0.313,0.198 10 false *1 2.854,1.573 3.167,1.771 0.313,0.198 10 true *2 0.51,1.719 0.719,1.917 0.208,0.198 10 true *3
*1 Inlet Heater Water Hose
*2 Outlet Heater Water Hose A
*3 Outlet Heater Water Hose B


Disengage the 2 claws and disconnect the inlet heater water hose and outlet heater water hose A.


b.

Slide the clip and disconnect the outlet heater water hose B from the cylinder head sub-assembly.


Hide 32941 35.DISCONNECT INLET NO.1 OIL COOLER HOSE

a.
A256231

Slide the clip and disconnect the inlet No.1 oil cooler hose from the automatic transaxle assembly.


Hide 32942 36.DISCONNECT OUTLET NO.1 OIL COOLER HOSE

a.
A256232

Slide the clip and disconnect the outlet No.1 oil cooler hose from the automatic transaxle assembly.


Hide 28100 37.REMOVE STARTER ASSEMBLY

Hide 82121 38.DISCONNECT ENGINE WIRE

a.

Remove the No. 1 relay block cover from the engine room relay block assembly.


b.
A320212

Remove the bolt and separate the earth wire.


c.

Remove the nut from the engine room relay block assembly.


d.

Disconnect the 3 wire clamps.


e.
A315806

Disconnect the 4 connectors from the engine room relay block assembly.


f.

Using a screwdriver, disengage the claw and separate the engine wire from the engine room relay block assembly.


g.
A315807

Pull up the lock lever while pushing the lock on the lever to disconnect the ECM connector.

NOTICE:

After disconnecting the ECM connector, make sure that dirt, water or other foreign matter does not contact the connecting part of the ECM connector.



h.

Disengage the 2 wire harness clamps.


Hide 17119A 39.REMOVE AIR CLEANER BRACKET

a.
A427235

Remove the 2 bolts and air cleaner bracket from the battery carrier.


Hide 33820B 40.SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C132236

Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.


b.
C204479

Remove the clip and disconnect the transmission control cable assembly from the No. 1 control cable bracket.


Hide 12327A 41.REMOVE NO. 2 ENGINE MOUNTING STAY RH

a.
A314938

Remove the 2 bolts and No. 2 engine mounting stay RH.


Hide 12313 42.REMOVE ENGINE MOVING CONTROL ROD BRACKET

a.
A314939

Remove the 4 bolts and engine moving control rod bracket.


Hide 12363A 43.REMOVE ENGINE MOVING CONTROL ROD

a.
A240877

Remove the bolt and engine moving control rod from the engine moving control rod bracket.

HINT:

Perform this procedure only when replacement of the engine moving control rod is necessary.



Hide 44774 44.DISCONNECT UNION TO VACUUM TUBE HOSE

a.
A316384

Slide the clip and disconnect the union to vacuum tube hose from the No. 1 vacuum hose assembly.


Hide 88703 45.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 88704 46.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 23901 47.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 17410 48.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 48810 50.SEPARATE FRONT STABILIZER LINK ASSEMBLY

Hide 89543 51.SEPARATE FRONT SPEED SENSOR

Hide 45470 52.SEPARATE TIE ROD ASSEMBLY LH

Hide 45460 53.SEPARATE TIE ROD ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48069 54.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 55.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 43420 56.SEPARATE FRONT DRIVE SHAFT ASSEMBLY

Hide 43420 57.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 58.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

Hide 43420G 59.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING (for LH Side)

Hide 45220 60.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 11361J 61.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
A196625

Remove the flywheel housing under cover.


Hide 63.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.
A315804C01
0,0 0,0 false
V100145

Attachment Installation Position


Place height adjustment attachments and plate lift attachments in the positions shown in the illustration and set an engine lifter underneath the engine assembly with transaxle.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, place the engine assembly with transaxle horizontally.

·

Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




b.
A315803C02
0.625,0.271 0.938,0.469 0.313,0.198 10 false *a 0.292,0.927 0.469,1.135 0.177,0.208 10 true *a 1.146,0.104 1.323,0.313 0.177,0.208 10 true *a 2.021,0.104 2.198,0.313 0.177,0.208 10 true *a 2.667,0.281 2.844,0.49 0.177,0.208 10 true *a 2.979,0.865 3.156,1.073 0.177,0.208 10 true *a 2.729,2.219 2.906,2.427 0.177,0.208 10 true *a 2.604,2.979 2.781,3.188 0.177,0.208 10 true *a 2.167,3.198 2.344,3.406 0.177,0.208 10 true *a 1.083,3.219 1.26,3.427 0.177,0.208 10 true *a 0.604,2.99 0.781,3.198 0.177,0.208 10 true *a 0.49,2.198 0.667,2.406 0.177,0.208 10 true *a 1.417,1.052 1.604,1.25 0.188,0.198 10 true *b 1.719,1.031 1.906,1.229 0.188,0.198 10 true *b 1.708,2.292 1.896,2.49 0.188,0.198 10 true *b 1.469,2.302 1.656,2.5 0.188,0.198 10 true *b
*a Bolt
*b Nut


Remove the 6 bolts, 2 nuts and frame side rail plate RH and frame side rail plate LH.


c.

Remove the 6 bolts, 2 nuts and front suspension member rear brace RH and front suspension member rear brace LH.


d.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




e.

Using an engine sling device and engine lift, secure the engine assembly with transaxle.


Hide 64.INSTALL ENGINE HANGERS

a.
A195856C10
0.333,2.073 0.5,2.073 0.5,2.073 0.833,1.573 false 3,2.052 2.854,2.052 2.854,2.052 2.5,1.26 false 0.094,1.979 0.302,2.167 0.208,0.188 10 false *1 3.031,1.948 3.24,2.135 0.208,0.188 10 false *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the No. 1 engine hanger and No. 2 engine hanger with the 2 bolts as shown in the illustration.

Part No.
Item Part No.
No. 1 Engine Hanger 12281-36020
No. 2 Engine Hanger 12282-36021
Bolt 91552-81040 or 91552-81025

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 82121 65.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine assembly with transaxle.


Hide 88310 67.REMOVE COMPRESSOR ASSEMBLY WITH PULLEY

Hide 27020 68.REMOVE GENERATOR ASSEMBLY

Hide 51100G 69.REMOVE FRONT FRAME ASSEMBLY

a.
A255456

Remove the nut and separate the engine mounting insulator LH.


b.
A288230

Remove the bolt and separate the front engine mounting insulator.


c.
A255455

Remove the nut and separate the engine mounting insulator RH.


d.

Remove the front frame assembly.


e.

Using height adjustment attachments and plate lift attachments, place the engine assembly with transaxle on a flat level surface.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, place the engine assembly with transaxle horizontally.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.




Hide 12361 70.REMOVE FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


a.
A315825

Remove the hole plug from the front frame assembly.


b.
A260916

Remove the 3 nuts and front engine mounting insulator.


Hide 12372A 71.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A315824

Remove the 2 hole plugs from the front frame assembly.


b.
A255459

Remove the 3 nuts and engine mounting insulator LH.


Hide 12362 72.REMOVE ENGINE MOUNTING INSULATOR RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator RH is necessary.


a.
A315823

Remove the 2 hole plugs from the front frame assembly.


b.
A255460

Remove the 3 nuts and engine mounting insulator RH.


Hide 43457 73.REMOVE DRIVE SHAFT BEARING BRACKET

a.
A196633

Remove the 3 bolts and drive shaft bearing bracket.


Hide 12315A 74.REMOVE ENGINE MOUNTING BRACKET RH

a.
A196634

Remove the 3 bolts and engine mounting bracket RH.


Hide 32101 76.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 77.INSTALL ENGINE TO ENGINE STAND

a.

Install the engine assembly to an engine stand.

NOTICE:
·

Adjust the angle of the sling device carefully to prevent the engine assembly or engine hangers from deforming or becoming damaged.

·

Do not perform any procedure while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




Hide 78.REMOVE ENGINE HANGERS

a.
A264710C09
1,0.229 1.25,0.229 false 2.729,0.24 2.969,0.24 false 1.271,0.125 1.479,0.313 0.208,0.188 10 false *1 3.042,0.146 3.25,0.313 0.208,0.167 10 false *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger.