Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge) › from 2016.11
RM3160E _52 Drivetrain _019727 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0107758 AUTOMATIC TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge) A

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge)  INSTALLATION  


PROCEDURE

Hide 32000 1.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C297896C01
2.198,1.01 2.292,0.542 2.292,0.542 2.51,0.542 true 1.083,1.063 0.938,0.604 0.938,0.604 0.771,0.615 true 1.24,2.063 1.021,2.073 1.021,2.073 1.104,1.635 true 2.573,0.469 2.885,0.625 0.313,0.156 10 false *a 0.573,0.552 0.885,0.708 0.313,0.156 10 false *b 1.292,1.979 1.604,2.135 0.313,0.156 10 false *b
*a Matchmark
*b Key


Turn the front oil pump drive gear so that the key is at the top and place a matchmark on the transaxle housing to indicate the position of the key.


b.
C057914C02
1.406,1.979 1.583,1.979 1.583,1.979 1.75,1.552 false 1.698,0.344 1.302,0.167 1.302,0.167 1.177,0.167 true 1.01,0.083 1.323,0.24 0.313,0.156 10 false *a 1.229,1.917 1.542,2.073 0.313,0.156 10 false *b
*a Groove
*b Matchmark


Place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.


c.
C297897C02
2.479,1.354 1.771,2 1.771,2 2.458,0.958 true 1.292,0.76 0.458,0.24 0.458,0.24 1.292,0.427 true 1.604,1.969 1.917,2.125 0.313,0.156 10 false *1 0.271,0.135 0.583,0.292 0.313,0.156 10 false *a
*1 Front Oil Pump Oil Seal
*a Matchmark


Align the matchmark on the transaxle housing with the one on the torque converter assembly and engage the splines of the input with the turbine runner splines.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




d.
C297898C01
1.302,0.375 1.385,0.104 1.385,0.104 1.531,0.104 true 0.917,2.031 1.083,2.031 1.083,2.031 1.281,1.604 true 2.458,1.313 1.875,1.938 1.875,1.938 2.469,0.969 true 1.708,1.917 2.021,2.073 0.313,0.156 10 false *1 1.604,0.021 1.917,0.177 0.313,0.156 10 false *a 0.74,1.948 1.052,2.104 0.313,0.156 10 false *a
*1 Front Oil Pump Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




e.
C297899C01
1.281,0.729 0.573,0.271 0.573,0.271 1.281,0.406 true 2.469,1.313 1.885,1.938 1.885,1.938 2.469,0.948 true 1.771,1.958 2.083,2.115 0.313,0.156 10 false *1 0.365,0.177 0.677,0.333 0.313,0.156 10 false *a
*1 Front Oil Pump Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the transaxle housing and insert the groove of the torque converter assembly into the key of the oil pump drive gear.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




f.

Clean the drive plate and torque converter assembly setting bolt holes.


g.
C299023C01
1.125,0.865 0.823,0.271 0.823,0.271 0.729,0.271 false 2.438,0.927 2.438,0.698 false 2.427,1.396 2.708,1.396 false 1.198,2.979 1.198,2.427 true 0.531,0.188 0.948,0.49 0.417,0.302 10 false *a 1.125,3.031 1.469,3.25 0.344,0.219 10 false *b 2.188,0.344 2.604,0.646 0.417,0.302 10 false A 2.365,0.958 2.781,1.26 0.417,0.302 10 false *a 2.24,1.292 2.656,1.604 0.417,0.313 10 false *b
*a Engine Surface
*b Drive Plate Surface


Using a vernier caliper and straightedge, measure the dimension (A) between the automatic transaxle assembly contact surface of the engine assembly*a and the torque converter assembly contact surfaces of the drive plate*b.


h.
C299024N01
2.479,0.281 2.719,0.615 0.24,0.333 10 false B

Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

Standard:

A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 35150 2.INSTALL TRANSMISSION CASE PLUG ASSEMBLY

a.

Coat the O-ring of a new transmission case plug assembly with ATF.


b.

Install the transmission case plug assembly to the automatic transaxle assembly.


Hide 33823 3.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the automatic transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 4.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 4 wire harness clamp brackets to the automatic transaxle assembly with the 4 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 31406A 5.INSTALL FLEXIBLE HOSE BRACKET SUB-ASSEMBLY

a.

Install the clamp to the flexible hose bracket sub-assembly.


b.

Install the flexible hose bracket sub-assembly to the automatic transaxle assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.

Connect the breather plug hose to the flexible hose bracket sub-assembly.


Hide 12311A 6.INSTALL FRONT ENGINE MOUNTING BRACKET

a.

Install the front engine mounting bracket to the automatic transaxle assembly with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 30500 7.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

a.
C299025C01
0.896,1.063 1.427,1.063 false 1.792,1.219 2.323,1.219 true 0.719,0.969 1.104,1.271 0.385,0.302 10 false *1 2.385,1.135 2.792,1.438 0.406,0.302 10 false *2
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch Spline Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum Grease Amount:

Approximately 1 g (0.0353 oz)



b.
C239000C01
2.417,2.271 2.531,2.427 0.115,0.156 10 false A 2.823,2.74 2.938,2.896 0.115,0.156 10 false A 0.938,2.302 1.052,2.458 0.115,0.156 10 false A 0.698,2.854 0.813,3.01 0.115,0.156 10 false B 2.948,3.417 3.063,3.573 0.115,0.156 10 false B 2.875,3.813 2.99,3.969 0.115,0.156 10 false C 2.667,4.156 2.781,4.313 0.115,0.156 10 false C 1.208,4.333 1.323,4.49 0.115,0.156 10 false C 0.802,4.177 0.917,4.333 0.115,0.156 10 false C 0.26,1.094 0.49,1.396 0.229,0.302 10 true *a 2.365,0.26 2.594,0.563 0.229,0.302 10 true *a
*a Knock Pin


While keeping the engine assembly and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and temporarily install the 9 bolts shown in the illustration.

Torque:
Bolt Bolt Length Torque
A 55 mm (2.17 in.) 64 N*m (653 kgf*cm, 47 ft.*lbf)
B 50 mm (1.97 in.) 46 N*m (469 kgf*cm, 34 ft.*lbf)
C 32 mm (1.26 in.) 44 N*m (449 kgf*cm, 32 ft.*lbf)
33 mm (1.30 in.) 43 N*m (438 kgf*cm, 32 ft.*lbf)


NOTICE:
·

Confirm that the 2 knock pins are installed to the automatic transaxle assembly contact surface of the engine cylinder block before installing the automatic transaxle assembly.

·

Do not forcibly pry on the automatic transaxle assembly.

·

Check that the torque converter assembly rotates.




Hide 8.CONNECT WIRE HARNESS

a.
C297895C02
2.438,0.604 2.719,0.813 0.281,0.208 10 true *a 1.177,1.115 1.385,1.323 0.208,0.208 10 true A 1.406,2.49 1.615,2.698 0.208,0.208 10 true B
*a Park/Neutral Position Switch Connector


Connect the 5 clamps to the automatic transaxle assembly.


b.

Install the wire harness to the automatic transaxle assembly with the 2 bolts.

Torque:
Bolt (A) : 19 N*m (194 kgf*cm, 14 ft.*lbf)
Bolt (B) : 23 N*m (235 kgf*cm, 17 ft.*lbf)


c.

Connect the park/neutral position switch connector.


Hide 82824 9.INSTALL WIRING HARNESS CONNECTOR

a.
C299017

Temporarily install the wiring harness connector to the automatic transaxle assembly.


b.
C238952N01
2.146,0.292 2.25,0.448 0.104,0.156 10 1 1.802,0.208 1.906,0.365 0.104,0.156 10 2

Install the wiring harness connector with the 2 bolts in the order shown in the illustration.

Torque:
11.3 N*m (115 kgf*cm, 8 ft.*lbf)


c.
C247470

Connect the wiring harness connector.


d.

Turn the lock lever and secure the connector with the lock lever.


Hide 11.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Hide 32101A 12.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
P000601C22
1.979,1.177 2.177,0.229 2.177,0.229 2.302,0.229 false 2.323,0.135 2.521,0.323 0.198,0.188 10 false *a
*a Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.



b.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

NOTICE:

First install the black colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver colored drive plate and torque converter assembly setting bolts.



Hide 11361J 13.INSTALL FLYWHEEL HOUSING UNDER COVER

Hide 14.CHECK AUTOMATIC TRANSAXLE SYSTEM

NOTICE:

If automatic transaxle parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION