Home › Engine / Hybrid System › 1AR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _019671 1AR-FE ENGINE CONTROL _0103543 SFI SYSTEM C

1AR-FE ENGINE CONTROL  SFI SYSTEM  P0660  Intake Manifold Tuning Valve Control Circuit / Open (Bank 1)  


DESCRIPTION

A255384C03
3.99,0.24 4.302,0.438 0.313,0.198 10 false *a 6.083,0.24 6.396,0.438 0.313,0.198 10 false *b
*a Intake Air Control Valve Open *b Intake Air Control Valve Closed


This circuit opens and closes the Intake Air Control Valve (IACV) in response to changes in the engine load in order to increase the intake efficiency (ACIS: Acoustic Control Induction System).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1) The following conditions are met simultaneously for 0.5 seconds or more (2 trip detection logic):
·

The voltage of terminal ACIS of the ECM is low when the vacuum switching valve assembly (for acoustic control induction system) is off.

·

The engine has been started.


·

Open or short in vacuum switching valve assembly (for acoustic control induction system) circuit

·

Vacuum switching valve assembly (for acoustic control induction system)

·

Semiconductor pwr integration ECU

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A315971E14
0.792,1 1.042,1.167 0.25,0.167 10 false B 0.792,0.813 0.958,0.979 0.167,0.167 10 false 1 1.042,1.167 1.708,1.333 0.667,0.167 10 false EFI-MAIN 0.479,2.521 1.063,2.688 0.583,0.167 10 false FL MAIN 0.604,3.198 1.104,3.365 0.5,0.167 10 false Battery 1.333,2.302 2.552,2.635 1.219,0.333 10 false Semiconductor Pwr Integration ECU 1.688,1.781 2.354,1.948 0.667,0.167 10 false EFI MAIN 2.542,1.5 2.792,1.667 0.25,0.167 10 false 1G 2.542,1.01 2.792,1.177 0.25,0.167 10 false 1G 2.604,0.813 2.771,0.979 0.167,0.167 10 false 7 2.604,1.313 2.771,1.479 0.167,0.167 10 false 6 3.135,1.167 3.802,1.333 0.667,0.167 10 false EFI NO. 3 3.792,0.906 3.958,1.073 0.167,0.167 10 false 2 5.094,0.906 5.26,1.073 0.167,0.167 10 false 1 3.854,1.344 4.188,1.51 0.333,0.167 10 false C10 3.854,1.5 5.479,2.063 1.625,0.563 10 false Vacuum Switching Valve Assembly (for Acoustic Control Induction System) 5.375,0.813 5.625,0.979 0.25,0.167 10 false 69 5.333,2.76 5.667,2.927 0.333,0.167 10 false A43 5.375,1.01 5.625,1.177 0.25,0.167 10 false C1 5.385,2.563 5.635,2.729 0.25,0.167 10 false 46 6.083,3.729 6.5,3.896 0.417,0.167 10 false ECM 5.698,2.76 6.167,2.927 0.469,0.167 10 false MREL 5.698,1.01 6.083,1.177 0.385,0.167 10 false ACIS

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVE THE VSV FOR INTAKE CONTROL)
A204525C03
0.405,0.02 1.096,0.198 0.691,0.178 10 *a 2.044,0.02 2.796,0.213 0.752,0.193 10 *b 0.766,0.595 0.96,0.764 0.194,0.169 10 *c 0.87,1.792 1.076,1.96 0.206,0.168 10 *2 0.119,1.649 0.298,1.824 0.179,0.175 10 *1 2.211,0.657 2.407,0.829 0.196,0.172 10 *c 0.485,1.461 0.317,1.645 false 0.686,1.35 0.941,1.784 false 2.342,1.815 2.548,1.983 0.206,0.168 10 *2 1.591,1.672 1.77,1.847 0.179,0.175 10 *1 1.957,1.484 1.79,1.668 false 2.159,1.373 2.414,1.807 false
*1 Port F
*2 Port E
*a ON
*b OFF
*c Air


a.

Disconnect the vacuum hose from port F on the vacuum switching valve assembly (for acoustic control induction system).


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Intake Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Intake Control
50004 234 3

f.

Operate the vacuum switching valve assembly (for acoustic control induction system) check the air flow.

Standard:
Activate the VSV for Intake Control Specified Condition
ON Air from port E flows out through port F
OFF Air from port E flows out through air filter


Result:
Result Proceed to
Abnormal A
Normal B


HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.




A

2.INSPECT VACUUM SWITCHING VALVE ASSEMBLY (FOR ACOUSTIC CONTROL INDUCTION SYSTEM)

B

2.INSPECT VACUUM SWITCHING VALVE ASSEMBLY (FOR ACOUSTIC CONTROL INDUCTION SYSTEM)
a.

Inspect the vacuum switching valve assembly (for acoustic control induction system).

Click hereEngine / Hybrid System>1AR-FE INTAKE / EXHAUST>VACUUM SWITCHING VALVE(for ACIS)>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE ASSEMBLY (FOR ACOUSTIC CONTROL INDUCTION SYSTEM))

NG

REPLACE VACUUM SWITCHING VALVE ASSEMBLY (FOR ACOUSTIC CONTROL INDUCTION SYSTEM)

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE ASSEMBLY (FOR ACOUSTIC CONTROL INDUCTION SYSTEM))
A194112C70
0.521,2.156 0.938,2.427 0.417,0.271 0.292,0.385 0.5,0.563 0.208,0.177 10 false *a 0.604,2.198 0.906,2.344 0.302,0.146 10 false C10
*a Front view of wire harness connector (to Vacuum Switching Valve Assembly (for Acoustic Control Induction System))


a.

Disconnect the vacuum switching valve assembly (for acoustic control induction system) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C10-2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE ASSEMBLY (FOR ACOUSTIC CONTROL INDUCTION SYSTEM) - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - VACUUM SWITCHING VALVE ASSEMBLY (FOR ACOUSTIC CONTROL INDUCTION SYSTEM))
4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE ASSEMBLY (FOR ACOUSTIC CONTROL INDUCTION SYSTEM) - ECM)
a.

Disconnect the vacuum switching valve assembly (for acoustic control induction system) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C10-1 - C1-69 (ACIS) Always Below 1 Ω
C10-1 or C1-69 (ACIS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SEMICONDUCTOR PWR INTEGRATION ECU - VACUUM SWITCHING VALVE ASSEMBLY (FOR ACOUSTIC CONTROL INDUCTION SYSTEM))
a.

Disconnect the semiconductor pwr integration ECU.


b.

Disconnect the vacuum switching valve assembly (for acoustic control induction system) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1G-7 - C10-2 Always Below 1 Ω
1G-7 or C10-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SEMICONDUCTOR PWR INTEGRATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR