Home › Engine / Hybrid System › 1AR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _019671 1AR-FE ENGINE CONTROL _0103543 SFI SYSTEM C

1AR-FE ENGINE CONTROL  SFI SYSTEM  P2014  Intake Manifold Runner Position Sensor / Switch Circuit (Bank 1)  P2016  Intake Manifold Runner Position Sensor / Switch Circuit Low (Bank 1)  P2017  Intake Manifold Runner Position Sensor / Switch Circuit High (Bank 1)  


DESCRIPTION

The Tumble Control Valve (TCV) position sensor is a non-contact type sensor.

The position sensor measures the opening angle of the tumble control valve. The sensor is reliable and accurate, as it is electrically controlled by Hall-effect elements.

A257646E05
5.104,1.365 5.292,1 false 6.5,3.063 6.625,3.25 false 4.104,1.292 3.594,0.146 3.594,0.146 3.781,0.146 false 1.031,1.729 1.573,0.833 1.573,0.833 1.406,0.833 false 0.635,1.74 0.094,0.854 0.094,0.854 0.271,0.854 false 0.073,3.458 1.417,3.927 1.344,0.469 10 Tumble Control Valve Position Sensor 0.313,0.74 0.865,0.938 0.552,0.198 10 Magnet 0.927,0.75 1.427,0.948 0.5,0.198 10 Hall IC 1.781,1.49 2.26,1.688 0.479,0.198 10 VCIA 2.625,3.427 3.104,3.625 0.479,0.198 10 ECM 6.417,1.01 6.896,1.208 0.479,0.198 10 Open 4.396,1.01 5.073,1.208 0.677,0.198 10 Closed 6.24,3.26 7.135,3.458 0.896,0.198 10 Stores P2016 5.333,0.885 6.323,1.083 0.99,0.198 10 Stores P2017 4.771,3.438 6.323,3.635 1.552,0.198 10 Range of Operation 4.094,3.896 6.979,4.094 2.885,0.198 10 Tumble Control Valve Opening Angle (Deg.) 1.781,2.146 2.26,2.344 0.479,0.198 10 IAC1 1.781,2.781 2.146,2.979 0.365,0.198 10 EIA1 2.656,1.375 2.969,1.573 0.313,0.198 10 5 V 4.01,1.302 4.323,1.5 0.313,0.198 10 4.8 3.927,1.76 4.24,1.958 0.313,0.198 10 3.39 3.927,2.719 4.24,2.917 0.313,0.198 10 0.94 6.156,3.604 6.469,3.802 0.313,0.198 10 70 4.01,2.885 4.323,3.083 0.313,0.198 10 0.2 4.125,3.031 4.292,3.229 0.167,0.198 10 0 4.531,3.615 4.698,3.813 0.167,0.198 10 0 3.219,3.052 3.531,3.25 0.313,0.198 10 E1 3.885,0.063 5.792,0.49 1.906,0.427 10 Tumble Control Valve Position Sensor Output Voltage (V)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2014 Intake Manifold Runner Position Sensor / Switch Circuit (Bank 1) The tumble control valve position sensor output voltage flutters up and down beyond the normal operating range (less than 0.2 V, or higher than 4.8 V) for more than 0.5 seconds (open or short) (1 trip detection logic).
·

Open or short in tumble control valve position sensor circuit

·

Tumble control valve position sensor (built into intake air control valve actuator)

·

ECM


Comes on DTC stored
P2016 Intake Manifold Runner Position Sensor / Switch Circuit Low (Bank 1) The tumble control valve position sensor output voltage is less than 0.2 V for more than 0.5 seconds (short) (1 trip detection logic).
·

Open or short in tumble control valve position sensor circuit

·

Tumble control valve position sensor (built into intake air control valve actuator)

·

ECM


Comes on DTC stored
P2017 Intake Manifold Runner Position Sensor / Switch Circuit High (Bank 1) The tumble control valve position sensor output voltage is higher than 4.8 V for more than 0.5 seconds (open) (1 trip detection logic).
·

Open or short in tumble control valve position sensor circuit

·

Tumble control valve position sensor (built into intake air control valve actuator)

·

ECM


Comes on DTC stored

HINT:

When DTC P2014, P2016 or P2017 is output, use the GTS to confirm the IAC Sensor Voltage (tumble control valve position sensor output voltage). Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / IAC Sensor Voltage.


IAC Sensor Voltage Malfunction
0.2 V or less
·

IAC1 circuit shorted

·

VCIA circuit open


4.8 V or higher
·

VCIA and IAC1 circuits shorted

·

IAC1 circuit open

·

EIA1 circuit open



MONITOR DESCRIPTION

The ECM IAC1 terminal voltage increases in correlation with the opening angle of the tumble control valve. When the tumble control valve is fully closed, approximately 0.94 V is applied to the IAC1 terminal. When the tumble control valve is fully open, approximately 3.39 V is applied to the IAC1 terminal.

When the output voltage of the IAC1 terminal deviates from the standard range, the ECM determines that a malfunction has occurred in the position sensor and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Intake air control valve actuator (for tumble control valve)
Frequency of Operation Continuous

COMPONENT OPERATING RANGE

Tumble control valve position sensor voltage 0.2 to 4.8 V

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 0.5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P2014, P2016 or P2017.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

If DTCs relating to different systems which share terminal EIA1 as their ground are stored simultaneously, there may be an open circuit between terminal EIA1 and ground.

·

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE IAC DUTY RATIO)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the IAC Duty Ratio / All Data / IAC Sensor Voltage.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the IAC Duty Ratio
Data List Display
IAC Sensor Voltage
50004 234 150 160

d.

Check the value of IAC Sensor Voltage while changing Control the IAC Duty Ratio from -100 to 100% (or from 100 to -100%) using the GTS.

OK:

The value of IAC Sensor Voltage remains between 0.2 and 4.8 V while Control the IAC Duty Ratio is changed from -100 to 100% (or from 100 to -100%).


HINT:
Control the IAC Duty Ratio Operation IAC Sensor Voltage (Normal) Suspected Trouble Area
·

IAC1 circuit shorted

·

VCIA circuit open


·

VCIA and IAC1 circuits shorted

·

IAC1 circuit open

·

EIA1 circuit open


Sensor malfunction
-100% 0.2 to 1.4 V Remains below 0.2 V Remains higher than 4.8 V Other than the voltage in the 2 columns on the left
100% 3.2 to 4.8 V Remains below 0.2 V Remains higher than 4.8 V



Result:
Proceed to
OK
NG



OK

2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2014, P2016 AND/OR P2017)

NG

3.CHECK HARNESS AND CONNECTOR (INTAKE AIR CONTROL VALVE ACTUATOR - ECM)
2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2014, P2016 AND/OR P2017)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON.


f.

Turn the GTS on.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P2014, P2016 and/or P2017 is output A
DTCs are not output B



A

B

3.CHECK HARNESS AND CONNECTOR (INTAKE AIR CONTROL VALVE ACTUATOR - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the intake air control valve actuator connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z4-3 (VDD) - C1-130 (VCIA) Always Below 1 Ω
Z4-1 (OUT) - C1-131 (IAC1) Always Below 1 Ω
Z4-2 (GND) - C1-129 (EIA1) Always Below 1 Ω
Z4-3 (VDD) or C1-130 (VCIA) - Body ground Always 10 kΩ or higher
Z4-1 (OUT) or C1-131 (IAC1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF INTAKE AIR CONTROL VALVE ACTUATOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF INTAKE AIR CONTROL VALVE ACTUATOR)
A211274C07
0.729,1.177 1.156,1.479 0.427,0.302 1.958,1.385 2.417,1.667 false 0.854,1.25 1.125,1.5 0.271,0.25 10 false Z4 0.292,0.052 0.615,0.333 0.323,0.281 10 false *a 2.25,1.698 2.74,1.875 0.49,0.177 10 false VDD
*a Front view of wire harness connector
(to Intake Air Control Valve Actuator)


a.

Disconnect the intake air control valve actuator connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Z4-3 (VDD) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

5.REPLACE INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)

NG

5.REPLACE INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)
a.

Replace the intake air control valve actuator (for tumble control valve).

Click hereEngine / Hybrid System>1AR-FE INTAKE / EXHAUST>INTAKE AIR CONTROL VALVE ACTUATOR(for TCV)>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2014, P2016 AND/OR P2017)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2014, P2016 AND/OR P2017)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON.


f.

Turn the GTS on.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P2014, P2016 and/or P2017 is output A
DTCs are not output B



A

B

END