Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2016.11
RM3160E _58 Vehicle Interior _019708 METER / GAUGE / DISPLAY _0104486 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1507  Open in Turn Signal Circuit  B1508  Short in Turn Signal / Hazard Flasher Circuit  


DESCRIPTION

These DTCs are stored when the combination meter assembly detects an open in a turn signal light circuit, or a short in a turn signal light circuit or the hazard warning light circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1507 Open in Turn Signal Circuit When IG voltage is 9.5 V or more and the following condition is detected:
·

Open in turn signal light circuit


·

LED

·

Bulb

·

Harness or connector

·

Instrument panel junction block assembly

·

Outer mirror control ECU assembly LH*

·

Outer mirror control ECU assembly RH*

·

Combination meter assembly


DTC stored -
B1508 Short in Turn Signal / Hazard Flasher Circuit When IG voltage is 9.5 V or more and the following condition is detected:
·

Short in turn signal light circuit or hazard warning light circuit


·

LED

·

Bulb

·

Harness or connector

·

Instrument panel junction block assembly

·

Outer mirror control ECU assembly LH*

·

Outer mirror control ECU assembly RH*

·

Combination meter assembly


DTC stored -

*: w/ Seat Position Memory


WIRING DIAGRAM

w/ Seat Position Memory


E288579E03
0.375,0.885 3.583,1.083 3.208,0.198 10 false Headlight Assembly RH 0.375,0.719 0.688,0.917 0.313,0.198 10 false A25 0.51,0.385 0.667,0.583 0.156,0.198 10 false 4 1.917,0.385 2.073,0.583 0.156,0.198 10 false 1 0.354,1.802 0.667,2 0.313,0.198 10 false M32 0.354,1.969 3.563,2.167 3.208,0.198 10 false Rear Combination Light Assembly RH 0.51,1.49 0.667,1.688 0.156,0.198 10 false 6 1.917,1.5 2.073,1.698 0.156,0.198 10 false 4 0.729,0.375 0.885,0.573 0.156,0.198 10 false E 0.729,1.49 0.885,1.688 0.156,0.198 10 false E 1.667,0.375 1.823,0.573 0.156,0.198 10 false B 4.167,0.271 4.323,0.469 0.156,0.198 10 false 7 4.125,0.479 4.417,0.677 0.292,0.198 10 false 4F 4.125,1.604 4.417,1.802 0.292,0.198 10 false 4H 4.167,1.396 4.458,1.573 0.292,0.177 10 false 6 5.177,0.281 5.469,0.458 0.292,0.177 10 false 1 4.125,2.417 4.417,2.594 0.292,0.177 10 false 15 4.135,2.615 4.427,2.813 0.292,0.198 10 false 4A 5.135,0.469 5.427,0.667 0.292,0.198 10 false 4A 5.823,0.354 6.115,0.531 0.292,0.177 10 false 13 6.125,0.469 6.417,0.667 0.292,0.198 10 false LR 4.167,3.052 5.781,3.5 1.615,0.448 10 false Instrument Panel Junction Block Assembly 1.792,2.604 2.115,2.833 0.323,0.229 10 false z9 1.792,3.125 2.115,3.354 0.323,0.229 10 false z9 1.792,2.406 2.083,2.583 0.292,0.177 10 false 16 1.792,2.927 2.083,3.104 0.292,0.177 10 false 12 2.125,2.594 2.281,2.792 0.156,0.198 10 false B 2.135,3.125 2.292,3.323 0.156,0.198 10 false - 2.646,2.594 3.26,2.792 0.615,0.198 10 false TRNI 2.646,3.125 3.26,3.323 0.615,0.198 10 false GND 3.104,2.604 3.427,2.833 0.323,0.229 10 false H2 3.104,3.135 3.427,3.365 0.323,0.229 10 false H2 3.094,2.406 3.385,2.583 0.292,0.177 10 false 11 3.146,2.927 3.302,3.125 0.156,0.198 10 false 7 0.469,3.5 1.833,3.833 1.365,0.333 10 false Side Turn Signal Light Assembly RH 2,3.5 3.25,3.865 1.25,0.365 10 false Outer Mirror Control ECU Assembly RH 5.906,4.75 6.198,4.927 0.292,0.177 10 false 7 6.125,4.854 6.417,5.052 0.292,0.198 10 false LL 0.51,4.75 0.667,4.948 0.156,0.198 10 false 4 1.917,4.75 2.073,4.948 0.156,0.198 10 false 1 1.927,5.719 2.083,5.917 0.156,0.198 10 false 4 0.5,5.719 0.656,5.917 0.156,0.198 10 false 6 0.75,4.75 0.906,4.948 0.156,0.198 10 false E 0.75,5.719 0.906,5.917 0.156,0.198 10 false E 1.49,5.729 1.875,5.927 0.385,0.198 10 false TRN 1.667,4.75 1.823,4.948 0.156,0.198 10 false B 0.333,5.25 3.542,5.448 3.208,0.198 10 false Headlight Assembly LH 0.354,5.083 0.667,5.281 0.313,0.198 10 false A17 0.333,6.219 3.542,6.417 3.208,0.198 10 false Rear Combination Light Assembly LH 0.333,6.052 0.792,6.25 0.458,0.198 10 false M30 4.167,4.667 4.323,4.865 0.156,0.198 10 false 5 4.167,5.656 4.458,5.833 0.292,0.177 10 false 7 3.115,6.656 3.406,6.833 0.292,0.177 10 false 11 3.156,7.188 3.313,7.385 0.156,0.198 10 false 7 1.792,6.667 2.083,6.844 0.292,0.177 10 false 16 1.792,7.167 2.083,7.344 0.292,0.177 10 false 12 1.75,6.875 2.073,7.104 0.323,0.229 10 false z10 1.75,7.396 2.073,7.625 0.323,0.229 10 false z10 3.125,6.865 3.448,7.094 0.323,0.229 10 false I2 3.135,7.385 3.458,7.615 0.323,0.229 10 false I2 2.125,6.865 2.333,7.031 0.208,0.167 10 false B 2.125,7.375 2.281,7.573 0.156,0.198 10 false - 2.625,6.854 3.24,7.052 0.615,0.198 10 false TRNI 2.646,7.385 3.26,7.583 0.615,0.198 10 false GND 4.125,5.854 4.417,6.052 0.292,0.198 10 false 4H 4.125,4.865 4.417,5.063 0.292,0.198 10 false 4F 4.135,6.656 4.427,6.833 0.292,0.177 10 false 20 4.125,6.865 4.417,7.063 0.292,0.198 10 false 4D 5.188,4.656 5.344,4.854 0.156,0.198 10 false 8 5.146,4.854 5.438,5.052 0.292,0.198 10 false 4D 4.083,7.333 5.729,7.781 1.646,0.448 10 false Instrument Panel Junction Block Assembly 5.802,5.302 6.094,5.5 0.292,0.198 10 false F21 5.792,5.5 7,5.917 1.208,0.417 10 false Combination Meter Assembly 0.417,7.771 1.792,8.188 1.375,0.417 10 false Side Turn Signal Light Assembly LH 2,7.771 3.25,8.135 1.25,0.365 10 false Outer Mirror Control ECU Assembly LH 1.5,1.469 1.885,1.667 0.385,0.198 10 false TRN


w/o Seat Position Memory


E288580E03
1.031,0.5 1.188,0.698 0.156,0.198 10 false 4 2.427,0.5 2.583,0.698 0.156,0.198 10 false 1 1.042,1.552 1.198,1.75 0.156,0.198 10 false 6 2.427,4.333 2.583,4.531 0.156,0.198 10 false 1 1.031,5.385 1.188,5.583 0.156,0.198 10 false 6 3.531,4.25 3.688,4.448 0.156,0.198 10 false 5 4.552,4.25 4.708,4.448 0.156,0.198 10 false 8 3.531,0.417 3.688,0.615 0.156,0.198 10 false 7 4.552,0.417 4.708,0.615 0.156,0.198 10 false 1 3.542,1.469 3.813,1.667 0.271,0.198 10 false 6 3.5,2.552 3.771,2.75 0.271,0.198 10 false 15 1.042,2.635 1.313,2.833 0.271,0.198 10 false 9 2.417,2.635 2.688,2.833 0.271,0.198 10 false 4 2.427,1.552 2.583,1.75 0.156,0.198 10 false 4 1.042,4.323 1.198,4.521 0.156,0.198 10 false 4 2.417,5.385 2.573,5.583 0.156,0.198 10 false 4 1.052,6.469 1.323,6.667 0.271,0.198 10 false 9 2.396,6.469 2.667,6.667 0.271,0.198 10 false 4 3.531,5.302 3.802,5.5 0.271,0.198 10 false 7 3.49,6.365 3.76,6.563 0.271,0.198 10 false 20 5.896,4.333 6.167,4.531 0.271,0.198 10 false 7 5.823,0.5 6.031,0.698 0.208,0.198 10 false 13 3.49,0.625 3.74,0.844 0.25,0.219 10 false 4F 3.49,1.677 3.74,1.896 0.25,0.219 10 false 4H 3.5,2.75 3.75,2.969 0.25,0.219 10 false 4A 4.51,0.625 4.76,0.844 0.25,0.219 10 false 4A 3.49,4.448 3.74,4.667 0.25,0.219 10 false 4F 3.49,5.5 3.74,5.719 0.25,0.219 10 false 4H 3.5,6.573 3.75,6.792 0.25,0.219 10 false 4D 4.51,4.448 4.76,4.667 0.25,0.219 10 false 4D 1.25,0.5 1.406,0.698 0.156,0.198 10 false E 2.167,0.5 2.323,0.698 0.156,0.198 10 false B 1.26,1.552 1.417,1.75 0.156,0.198 10 false E 2.177,2.635 2.333,2.833 0.156,0.198 10 false B 1.26,2.625 1.417,2.823 0.156,0.198 10 false E 6.094,0.615 6.375,0.833 0.281,0.219 10 false LR 6.094,4.438 6.375,4.656 0.281,0.219 10 false LL 1.25,4.323 1.406,4.521 0.156,0.198 10 false E 1.25,5.385 1.406,5.583 0.156,0.198 10 false E 1.26,6.469 1.417,6.667 0.156,0.198 10 false E 2.167,4.333 2.323,4.531 0.156,0.198 10 false B 2.021,5.375 2.49,5.583 0.469,0.208 10 false TRN 2.167,6.469 2.323,6.667 0.156,0.198 10 false B 3.375,3.208 5,3.667 1.625,0.458 10 false Instrument Panel Junction Block Assembly 3.375,7 5,7.458 1.625,0.458 10 false Instrument Panel Junction Block Assembly 0.875,0.833 1.188,1.031 0.313,0.198 10 false A25 0.875,1 4.083,1.198 3.208,0.198 10 false Headlight Assembly RH 0.667,1.885 0.979,2.083 0.313,0.198 10 false M32 0.667,2.052 5.865,2.25 5.198,0.198 10 false Rear Combination Light Assembly RH 0.667,2.969 0.979,3.167 0.313,0.198 10 false H1 0.667,3.135 5.865,3.333 5.198,0.198 10 false Side Turn Signal Light Assembly RH 0.833,4.667 1.146,4.865 0.313,0.198 10 false A17 0.833,4.833 4.042,5.031 3.208,0.198 10 false Headlight Assembly LH 0.583,5.719 0.896,5.917 0.313,0.198 10 false M30 0.583,5.885 5.781,6.083 5.198,0.198 10 false Rear Combination Light Assembly LH 0.604,6.802 0.917,7 0.313,0.198 10 false I1 0.583,6.969 5.781,7.167 5.198,0.198 10 false Side Turn Signal Light Assembly LH 5.75,4.917 6.052,5.135 0.302,0.219 10 false F21 5.75,5.083 6.979,5.5 1.229,0.417 10 false Combination Meter Assembly 2.021,1.552 2.49,1.76 0.469,0.208 10 false TRN


CAUTION / NOTICE / HINT

NOTICE:

Inspect the LEDs and bulbs for this system before performing the following procedure.


PROCEDURE

1.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
All RH turn signal lights or all LH turn signal lights do not blink A
RH side turn signal light does not illuminate B
LH side turn signal light does not illuminate C



A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)

B

4.CHECK TURN SIGNAL LIGHTS (RH SIDE)

C

15.CHECK TURN SIGNAL LIGHTS (LH SIDE)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
a.

Disconnect the F21 combination meter assembly connector.


b.

RH side

i.

Disconnect the 4A instrument panel junction block assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F21-13 (LR) - 4A-1 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F21-13 (LR) - Body ground Always 10 kΩ or higher




c.

LH side

i.

Disconnect the 4D instrument panel junction block assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F21-7 (LL) - 4D-8 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
F21-7 (LL) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E293101C01
5.177,0.208 5.531,0.427 0.354,0.219 1.958,0.156 2.313,0.375 0.354,0.219 5.167,1.5 5.521,1.719 0.354,0.219 1.969,1.5 2.323,1.719 0.354,0.219 0.385,0.135 0.698,0.292 0.313,0.156 10 false *a 2.052,0.188 2.271,0.354 0.219,0.167 10 false 4A 5.26,0.24 5.479,0.406 0.219,0.167 10 false 4D 2.073,1.531 2.292,1.698 0.219,0.167 10 false 4F 5.26,1.531 5.479,1.698 0.219,0.167 10 false 4H
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

RH side

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-1 - 4F-7 Always Below 1 Ω
4A-1 - 4H-6 Always Below 1 Ω
4A-1 - 4A-15 Always Below 1 Ω




c.

LH side

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-8 - 4F-5 Always Below 1 Ω
4D-8 - 4H-7 Always Below 1 Ω
4D-8 - 4D-20 Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK TURN SIGNAL LIGHTS (RH SIDE)
a.

Turn the ignition switch to ON.


b.

Set the headlight dimmer switch assembly to the right turn switch position.


c.

Check the operation of the turn signal lights.


Result:
Result Proceed to
Front turn signal light assembly does not blink A
Side turn signal light assembly does not blink B
Rear turn signal light assembly does not blink C



A

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)

B

7.CONFIRM VEHICLE TYPE

C

13.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
a.

Disconnect the A25 headlight assembly RH connector.


b.

Disconnect the 4F instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A25-1 (B) - 4F-7 Always Below 1 Ω
A25-4 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
4F-7 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E274732C06
1.896,0.583 2.365,0.854 0.469,0.271 5.313,0.542 5.781,0.813 0.469,0.271 2.052,0.625 2.573,0.927 0.521,0.302 10 false 4A 5.458,0.583 5.979,0.885 0.521,0.302 10 false 4F 0.448,0.292 0.969,0.594 0.521,0.302 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-1 - 4F-7 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.CONFIRM VEHICLE TYPE
a.

Confirm the vehicle type.


Result:
Result Proceed to
w/ Seat Position Memory A
w/o Seat Position Memory B



A

8.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)

B

11.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
8.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
a.

Disconnect the H2 outer mirror control ECU assembly RH connector.


b.

Disconnect the 4A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
H2-11 (TRNI) - 4A-15 Always Below 1 Ω
H2-7 (GND) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
4A-15 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E288837C02
1.573,0.781 1.948,1.063 0.375,0.281 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 1.677,0.844 1.99,1.042 0.313,0.198 10 false 4A
*a Component without harness connected
(Instrument Panel Junction Block Assembly)


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-1 - 4A-15 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

10.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH
a.

Replace the outer mirror control ECU assembly RH with a new or known good one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL


b.

Check for the DTCs.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

REPLACE COMBINATION METER ASSEMBLY

B

END

11.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
a.

Disconnect the H1 side turn signal light assembly RH connector.


b.

Disconnect the 4A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
H1-4 (B) - 4A-15 Always Below 1 Ω
H1-9 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
4A-15 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E288837C02
1.573,0.781 1.948,1.063 0.375,0.281 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 1.677,0.844 1.99,1.042 0.313,0.198 10 false 4A
*a Component without harness connected
(Instrument Panel Junction Block Assembly)


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-1 - 4A-15 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
a.

Disconnect the M32 rear combination light assembly RH connector.


b.

Disconnect the 4H instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
M32-4 (TRN) - 4H-6 Always Below 1 Ω
M32-6 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
4H-6 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E274731C05
1.771,0.563 2.271,0.854 0.5,0.292 5.354,0.542 5.854,0.833 0.5,0.292 0.365,0.427 0.854,0.781 0.49,0.354 10 false *a 1.927,0.635 2.708,1.115 0.781,0.479 10 false 4A 5.521,0.615 6.302,1.094 0.781,0.479 10 false 4H
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-1 - 4H-6 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

15.CHECK TURN SIGNAL LIGHTS (LH SIDE)
a.

Turn the ignition switch to ON.


b.

Set the headlight dimmer switch assembly to the left turn switch position.


c.

Check the operation of the turn signal lights.


Result:
Result Proceed to
Front turn signal light assembly does not blink A
Side turn signal light assembly does not blink B
Rear turn signal light assembly does not blink C



A

16.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)

B

18.CONFIRM VEHICLE TYPE

C

24.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
16.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
a.

Disconnect the A17 headlight assembly LH connector.


b.

Disconnect the 4F instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A17-1 (B) - 4F-5 Always Below 1 Ω
A17-4 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A17-1 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E288834C01
1.865,0.458 2.281,0.708 0.417,0.25 4.958,0.458 5.375,0.708 0.417,0.25 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 2,0.5 2.25,0.667 0.25,0.167 10 false 4D 5.083,0.5 5.333,0.667 0.25,0.167 10 false 4F
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-8 - 4F-5 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

18.CONFIRM VEHICLE TYPE
a.

Confirm the vehicle type.


Result:
Result Proceed to
w/ Seat Position Memory A
w/o Seat Position Memory B



A

19.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)

B

22.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
19.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
a.

Disconnect the I2 outer mirror control ECU assembly LH connector.


b.

Disconnect the 4D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
I2-11 (TRNI) - 4D-20 Always Below 1 Ω
I2-7 (GND) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
4D-20 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

20.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E288838C01
1.49,0.656 1.875,0.948 0.385,0.292 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 1.604,0.719 1.917,0.917 0.313,0.198 10 false 4D
*a Component without harness connected
(Instrument Panel Junction Block Assembly)


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-8 - 4D-20 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

21.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

21.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH
a.

Replace the outer mirror control ECU assembly LH with a new or known good one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL


b.

Check for the DTCs.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

REPLACE COMBINATION METER ASSEMBLY

B

END

22.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
a.

Disconnect the I1 side turn signal light assembly LH connector.


b.

Disconnect the 4D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
I1-4 (B) - 4D-20 Always Below 1 Ω
I1-9 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
4D-20 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.
E288838C01
1.49,0.656 1.875,0.948 0.385,0.292 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 1.604,0.719 1.917,0.917 0.313,0.198 10 false 4D
*a Component without harness connected
(Instrument Panel Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-8 - 4D-20 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

24.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
a.

Disconnect the M30 rear combination light assembly LH connector.


b.

Disconnect the 4H instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
M30-4 (TRN) - 4H-7 Always Below 1 Ω
M30-6 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
4H-7 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

25.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E288836C01
1.615,0.375 2.031,0.625 0.417,0.25 4.875,0.375 5.292,0.625 0.417,0.25 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 1.75,0.417 2,0.583 0.25,0.167 10 false 4D 5,0.417 5.25,0.583 0.25,0.167 10 false 4H
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-8 - 4H-7 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY