The combination meter assembly receives a text data signal from the navigation receiver assembly*1 or radio and display receiver assembly*2 via local bus communication.
Based on this signal, navigation system information is displayed on the multi-information display.
This DTC is stored when the combination meter assembly cannot receive the signal.
*1: for Navigation Receiver Type
*2: for Radio and Display Type
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| B150A | Lost Communication with HMI-LAN | After the combination meter assembly receives a registration information signal, which is sent by the navigation receiver assembly*1 or radio and display receiver assembly*2 when the ignition switch is ACC, 1 or more times, the combination meter assembly cannot receive the signal for 30 seconds or more. | ·
Harness or connector ·
Navigation receiver assembly*1 ·
Radio and display receiver assembly*2 ·
Combination meter assembly |
DTC stored | - |
*1: for Navigation Receiver Type
*2: for Radio and Display Type
for Navigation Receiver Type
for Radio and Display Type
Check if Navigation System DTCs are output.
for Navigation Receiver Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>DTC CHECK / CLEAR
for Radio and Display Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR
Navigation system DTCs are not output.
| Result | Proceed to |
|---|---|
| Navigation system DTCs are not output | A |
| Navigation system DTCs are output | B |
A
B
for Navigation Receiver Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>HOW TO PROCEED WITH TROUBLESHOOTING
for Radio and Display Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the F126 combination meter assembly connector.
Disconnect the F117 navigation receiver assembly*1 or F72 radio and display receiver assembly*2 connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F117-3 (CNH1) - F126-29 (MSCH)*1 | Always | Below 1 Ω |
| F117-4 (CNL1) - F126-30 (MSCL)*1 | Always | Below 1 Ω |
| F72-3 (CNH1) - F126-29 (MSCH)*2 | Always | Below 1 Ω |
| F72-4 (CNL1) - F126-30 (MSCL)*2 | Always | Below 1 Ω |
| F126-29 (MSCH) - Body ground | Always | 10 kΩ or higher |
| F126-30 (MSCL) - Body ground | Always | 10 kΩ or higher |
*1: for Navigation Receiver Type
*2: for Radio and Display Type
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the combination meter assembly with a new or known good one.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
Turn the ignition switch to ON and wait 30 seconds.
A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and navigation receiver assembly*1 or radio and display receiver assembly*2.
*1: for Navigation Receiver Type
*2: for Radio and Display Type
Operate the steering pad switch assembly and check that the audio tab illuminates.
Check for DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| The audio tab illuminates and DTC B150A is not output | A |
| The audio tab does not illuminate and DTC B150A is output (for Navigation Receiver Type) | B |
| The audio tab does not illuminate and DTC B150A is output (for Radio and Display Type) | C |
A
B
C