Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1232  Acceleration Sensor Stuck Malfunction  C1243  Acceleration Sensor Stuck Malfunction  C1245  Acceleration Sensor Output Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.

HINT:

If there is a malfunction in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) is output. When DTC U0124 is output together with C1232, C1243 and/or C1245, inspect and repair the trouble areas indicated by U0124 first.


DTCs may be stored if either of the following occurs:

·

Yaw rate and acceleration sensor (airbag sensor assembly) installation abnormality.

·

Yaw rate and acceleration sensor signal malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1232 Acceleration Sensor Stuck Malfunction At a vehicle speed of 10 km/h (6 mph) or more, the acceleration sensor output value does not change for 1 second or more.
·

Sensor installation

·

Acceleration sensor (airbag sensor assembly)


C1243 Acceleration Sensor Stuck Malfunction Either of the following is detected:
1.

While the vehicle speed changes from 30 km/h (19 mph) to 0 km/h (0 mph), the condition in which the value of the acceleration sensor does not change by 0.0294 G or more occurs 16 times or more.

2.

The output value of the acceleration sensor is more than 1.405 G in both axes for 60 seconds or more.


·

Sensor installation

·

Acceleration sensor (airbag sensor assembly)


C1245 Acceleration Sensor Output Malfunction At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated from the acceleration sensor value and that calculated from the vehicle speed sensor exceeds 0.35 G for 60 seconds or more.
·

Sensor installation

·

Acceleration sensor (airbag sensor assembly)



HINT:

for C1243 and C1245: Even after the trouble areas are repaired, the ABS warning light will not go off unless the following operations are performed.

1.

Drive the vehicle at 30 km/h (19 mph) for 30 seconds or more and check that the ABS warning light goes off.

2.

Clear the DTCs.



CAUTION / NOTICE / HINT

NOTICE:

When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


HINT:

When U0124 is output together with C1232, C1243, and/or C1245, inspect and repair the trouble areas indicated by U0124 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073


PROCEDURE

1.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The sensor is tightened to the specified torque.

The sensor is not installed in a tilted position.


NOTICE:

Check the yaw rate and acceleration sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG