Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display DTCs by blinking the ABS warning and slip indicator lights.

WIRING DIAGRAM

C369736E01
5.969,0.698 6.583,0.896 0.615,0.198 10 false CANL 5.698,0.51 6.313,0.708 0.615,0.198 10 false 10 5.979,1.385 6.594,1.583 0.615,0.198 10 false CANH 5.708,1.208 6.323,1.406 0.615,0.198 10 false 22 5.458,1.927 7.042,2.406 1.583,0.479 10 false Skid Control ECU (Brake Actuator Assembly) 5.469,1.74 6.083,1.938 0.615,0.198 10 false A86 0.927,0.708 1.542,0.906 0.615,0.198 10 false CANL 0.906,1.396 1.521,1.594 0.615,0.198 10 false CANH 6.125,4.313 6.74,4.51 0.615,0.198 10 false DLC3 5.979,2.958 6.594,3.156 0.615,0.198 10 false TC 6.135,4.146 6.75,4.344 0.615,0.198 10 false F25 5.708,2.854 6.323,3.052 0.615,0.198 10 false 13 5.781,3.458 6.396,3.656 0.615,0.198 10 false 4 5.979,3.583 6.594,3.781 0.615,0.198 10 false CG 2.792,3.719 4.5,4.031 1.708,0.313 10 false : CAN Communication Line 1.417,2.667 2.031,2.865 0.615,0.198 10 false 23*1 0.75,4.313 1.365,4.51 0.615,0.198 10 false ECM 0.75,4.146 1.365,4.344 0.615,0.198 10 false A43 1.125,2.99 1.74,3.188 0.615,0.198 10 false TC 1.417,2.833 2.031,3.031 0.615,0.198 10 false 33*2 2.677,4.073 4.385,4.385 1.708,0.313 10 false *1: for 1AR-FE 2.677,4.406 4.385,4.719 1.708,0.313 10 false *2: for 2GR-FKS 1.396,0.51 2.01,0.708 0.615,0.198 10 false 26 1.396,1.198 2.01,1.396 0.615,0.198 10 false 13

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


HINT:

When the indicator lights continue to blink, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in one or more ECUs is suspected.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.INSPECT DLC3

B

2.INSPECT DLC3
a.
C207407C86
0.25,0.979 0.698,1.271 0.448,0.292 1.823,2.365 2.375,1.01 true 1.594,1.885 1.135,1.01 true 0.333,0.302 0.521,0.469 0.188,0.167 10 false *a 2.313,0.813 2.552,0.979 0.24,0.167 10 false TC 0.375,1.042 0.771,1.313 0.396,0.271 10 false F25 1.021,0.813 1.26,0.979 0.24,0.167 10 false CG
*a Front view of DLC3


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F25-13 (TC) - F25-4 (CG) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
3.REPLACE ECM
a.
C207407C86
0.25,0.979 0.698,1.271 0.448,0.292 1.823,2.365 2.375,1.01 true 1.594,1.885 1.135,1.01 true 0.333,0.302 0.521,0.469 0.188,0.167 10 false *a 2.313,0.813 2.552,0.979 0.24,0.167 10 false TC 0.375,1.042 0.771,1.313 0.396,0.271 10 false F25 1.021,0.813 1.26,0.979 0.24,0.167 10 false CG
*a Front view of DLC3


Turn the ignition switch off.



c.

Using SST, connect terminals TC and CG of the DLC3.


SST
09843-18040  

d.

Check that the ABS warning and slip indicator lights are blinking.

OK:

The ABS warning and slip indicator lights are blinking.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

END

NG

4.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the A43 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1AR-FE
Tester Connection Condition Specified Condition
F25-13 (TC) - A43-23 (TC) Always Below 1 Ω
F25-13 (TC) or A43-23 (TC) - Body ground Always 10 kΩ or higher

for 2GR-FKS
Tester Connection Condition Specified Condition
F25-13 (TC) - A43-33 (TC) Always Below 1 Ω
F25-13 (TC) or A43-33 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C207407C87
0.25,0.979 0.698,1.271 0.448,0.292 1.594,1.885 2.438,0.958 true 0.333,0.302 0.521,0.469 0.188,0.167 10 false *a 0.375,1.042 0.708,1.302 0.333,0.26 10 false F25 2.438,0.76 2.677,0.927 0.24,0.167 10 false CG
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F25-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE ECM
a.
C207407C86
0.25,0.979 0.698,1.271 0.448,0.292 1.823,2.365 2.375,1.01 true 1.594,1.885 1.135,1.01 true 0.333,0.302 0.521,0.469 0.188,0.167 10 false *a 2.313,0.813 2.552,0.979 0.24,0.167 10 false TC 0.375,1.042 0.771,1.313 0.396,0.271 10 false F25 1.021,0.813 1.26,0.979 0.24,0.167 10 false CG
*a Front view of DLC3


Replace the ECM.

for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>ECM>REMOVAL

for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>REMOVAL


b.

Using SST, connect terminals TC and CG of the DLC3.


SST
09843-18040  

c.

Check that the ABS warning and slip indicator lights are blinking.

OK:

The ABS warning and slip indicator lights are blinking.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

END

NG