Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › from 2016.11
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0097123 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  B279A  Theft Deterrent System Communication Line High Fixation  B279A12  Engine Immobiliser System Circuit Short to Battery  


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck high (e.g. shorted to +B), the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A Theft Deterrent System Communication Line High Fixation Communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck high.
·

Wire harness or connector

·

ECM

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Turn the ignition switch to ON and wait 6 seconds.


B279A12 Engine Immobiliser System Circuit Short to Battery Communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck high.
·

Wire harness or connector

·

ECM

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Turn the ignition switch to ON and wait 6 seconds.



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
·

B279A*1

·

B279A12*2


-

*1: for 1AR-FE

*2: for 2GR-FKS


WIRING DIAGRAM

B366893E32
1.802,0.885 2.573,1.073 0.771,0.188 10 false 28*1, 59*2 5.208,0.885 5.49,1.073 0.281,0.188 10 false 13 1.469,1.01 1.875,1.24 0.406,0.229 10 false IMI 5.479,1 5.885,1.229 0.406,0.229 10 false EFIO 1.083,1.823 1.49,2.052 0.406,0.229 10 false A43 1.073,1.979 1.479,2.208 0.406,0.229 10 false ECM 5.219,1.802 5.625,2.031 0.406,0.229 10 false F66 5.208,1.958 6.594,2.344 1.385,0.385 10 false Transponder Key ECU Assembly 2.583,1.979 3.656,2.229 1.073,0.25 10 false *1: for 1AR-FE 2.583,2.292 3.656,2.542 1.073,0.25 10 false *2: for 2GR-FKS

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234
Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Powertrain > Engine > Trouble Codes
50001 372
OK:

DTC B279A*1 or B279A12*2 is not output.



Result:
Result Proceed to
B279A*1 or B279A12*2 is not output A
B279A*1 or B279A12*2 is output B


*1: for 1AR-FE

*2: for 2GR-FKS



A

B

3.CHECK CONNECTION OF CONNECTOR
3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the F66 transponder key ECU assembly connector.


b.

Disconnect the A43 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F66-13 (EFIO) - A43-28 (IMI)*1 Always Below 1 Ω
F66-13 (EFIO) - A43-59 (IMI)*2 Always Below 1 Ω
A43-28 (IMI) or F66-13 (EFIO) - Body ground*1 Always 10 kΩ or higher
A73-59 (IMI) or F66-13 (EFIO) - Body ground*2 Always 10 kΩ or higher


*1: for 1AR-FE

*2: for 2GR-FKS



Result:
Proceed to
OK
NG



OK

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234
Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Powertrain > Engine > Trouble Codes
50001 372
OK:

DTC B279A*1 or B279A12*2 is not output.



Result:
Result Proceed to
B279A*1 or B279A12*2 is not output A
B279A*1 or B279A12*2 is output B


*1: for 1AR-FE

*2: for 2GR-FKS



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B