Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System) › from 2016.11
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0095462 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  B2799  Engine Immobiliser System Malfunction  B279986  Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid  


DESCRIPTION

When there is a communication malfunction between the ECM and ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2, or when the communication ID codes do not match, the ECM stores this DTC.

*1: w/ Rear Seat Heater

*2: w/o Rear Seat Heater


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Engine Immobiliser System Malfunction Either condition is met (1 trip detection logic*1)*2:
·

A malfunction in the communication or communication lines between the ECM and ID code box (immobiliser code ECU).

·

A matching communication code cannot be verified during communication between the ECM and ID code box (immobiliser code ECU).


Either condition is met (1 trip detection logic*1)*3:
·

A malfunction in the communication or communication lines between the ECM and certification ECU (smart key ECU assembly).

·

A matching communication code cannot be verified during communication between the ECM and certification ECU (smart key ECU assembly).


·

ID code box (immobiliser code ECU)*2

·

ECM

·

Wire harness or connector

·

Certification ECU (smart key ECU assembly)*3


DTC output confirmation operation (Either condition is met):
·

Within 10 seconds of an engine start operation being performed (with the shift lever in P and the brake pedal depressed, the engine switch is pressed while the key is being carried). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

10 seconds after the engine switch is turned on (IG) after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds).


B279986 Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid Either condition is met (1 trip detection logic*1)*2:
·

A malfunction in the communication or communication lines between the ECM and ID code box (immobiliser code ECU).

·

A matching communication code cannot be verified during communication between the ECM and ID code box (immobiliser code ECU).


Either condition is met (1 trip detection logic*1)*3:
·

A malfunction in the communication or communication lines between the ECM and certification ECU (smart key ECU assembly).

·

A matching communication code cannot be verified during communication between the ECM and certification ECU (smart key ECU assembly).


·

ID code box (immobiliser code ECU)*2

·

ECM

·

Wire harness or connector

·

Certification ECU (smart key ECU assembly)*3


DTC output confirmation operation (Either condition is met):
·

Within 10 seconds of an engine start operation being performed (with the shift lever in P and the brake pedal depressed, the engine switch is pressed while the key is being carried). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

10 seconds after the engine switch is turned on (IG) after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds).



*1: Only output while a malfunction is present.

*2: w/ Rear Seat Heater

*3: w/o Rear Seat Heater


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
·

2799*1

·

B279986*2


-

*1: for 1AR-FE

*2: for 2GR-FKS


WIRING DIAGRAM

w/ Rear Seat Heater


B366892E22
1.469,0.781 1.823,0.969 0.354,0.188 10 false IMI 1.417,1.417 1.771,1.604 0.354,0.188 10 false IMO 1.083,2.073 1.552,2.313 0.469,0.24 10 false ECM 1.094,1.917 1.563,2.156 0.469,0.24 10 false A43 5.104,1.885 5.573,2.125 0.469,0.24 10 false F67 5.104,2.031 6.698,2.448 1.594,0.417 10 false ID Code Box (Immobiliser Code ECU) 1.781,0.656 2.688,0.875 0.906,0.219 10 false 28*1, 59*2 1.792,1.302 2.698,1.521 0.906,0.219 10 false 29*1, 45*2 2.708,2.052 3.896,2.281 1.188,0.229 10 false *1: for 1AR-FE 2.708,2.354 3.896,2.583 1.188,0.229 10 false *2: for 2GR-FKS 5.49,0.76 5.99,0.969 0.5,0.208 10 false EFIO 5.469,1.385 5.969,1.594 0.5,0.208 10 false EFII 5.292,0.656 5.573,0.865 0.281,0.208 10 false 4 5.292,1.302 5.573,1.51 0.281,0.208 10 false 3


w/o Rear Seat Heater


B366892E23
1.469,0.781 1.823,0.969 0.354,0.188 10 false IMI 1.417,1.417 1.771,1.604 0.354,0.188 10 false IMO 1.083,2.073 1.552,2.313 0.469,0.24 10 false ECM 1.094,1.917 1.563,2.156 0.469,0.24 10 false A43 5.104,1.885 5.573,2.125 0.469,0.24 10 false F10 5.104,2.031 6.625,2.448 1.521,0.417 10 false Certification ECU (Smart Key ECU Assembly) 1.771,0.656 2.677,0.875 0.906,0.219 10 false 59 1.792,1.302 2.698,1.521 0.906,0.219 10 false 45 5.49,0.76 5.99,0.969 0.5,0.208 10 false EFIO 5.469,1.385 5.969,1.594 0.5,0.208 10 false EFII 5.281,0.656 5.563,0.865 0.281,0.208 10 false 6 5.292,1.302 5.573,1.51 0.281,0.208 10 false 7


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the ECM, ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2, refer to Service Bulletin.

*1: w/ Rear Seat Heater

*2: w/o Rear Seat Heater


·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When DTC B2799*1, B279986*2 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.


*1: for 1AR-FE

*2: for 2GR-FKS


PROCEDURE

1.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234
Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Powertrain > Engine > Trouble Codes
50001 372
OK:

B2799*1 or B279986*2 is not output.


*1: for 1AR-FE

*2: for 2GR-FKS



Result:
Result Proceed to
OK A
NG (w/ Rear Seat Heater) B
NG (w/o Rear Seat Heater) C



A

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

B

4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

C

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the F67 ID code box (immobiliser code ECU) connector.


b.

Disconnect the A43 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F67-4 (EFIO) - A43-28 (IMI)*1 Always Below 1 Ω
F67-4 (EFIO) - A43-59 (IMI)*2 Always Below 1 Ω
F67-3 (EFII) - A43-29 (IMO)*1 Always Below 1 Ω
F67-3 (EFII) - A43-45 (IMO)*2 Always Below 1 Ω
F67-4 (EFIO) or A43-28 (IMI) - Body ground*1 Always 10 kΩ or higher
F67-4 (EFIO) or A43-59 (IMI) - Body ground*2 Always 10 kΩ or higher
F67-3 (EFII) or A43-29 (IMO) - Body ground*1 Always 10 kΩ or higher
F67-3 (EFII) or A43-45 (IMO) - Body ground*2 Always 10 kΩ or higher


*1: for 1AR-FE

*2: for 2GR-FKS



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE ECM
a.

Temporarily replace the ECM with a new one.

for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>REMOVAL

for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234
Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Powertrain > Engine > Trouble Codes
50001 372
OK:

B2799*1 or B279986*2 is not output.


*1: for 1AR-FE

*2: for 2GR-FKS



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the F10 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A43 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F10-6 (EFIO) - A43-59 (IMI) Always Below 1 Ω
F10-7 (EFII) - A43-45 (IMO) Always Below 1 Ω
F10-6 (EFIO) or A43-59 (IMI) - Body ground Always 10 kΩ or higher
F10-7 (EFII) or A43-45 (IMO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE ECM
a.

Temporarily replace the ECM with a new one.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
10.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Perform "DTC Output Confirmation Operation" procedure.


b.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372
OK:

B279986 is not output.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)