Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › from 2016.11
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0095460 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate  


DESCRIPTION

If the entry lock and wireless lock operations cannot be performed, there may be smart door control receiver assembly malfunctions, wave interference or problems in the communication which is used for the entry and wireless function between the smart door control receiver assembly and certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B358067E09
1.26,0.573 2.396,0.823 1.135,0.25 10 false to IG1 Relay 1.271,1.292 2.406,1.542 1.135,0.25 10 false to ACC Relay 1.302,1.979 2.438,2.229 1.135,0.25 10 false from Battery 3.063,2.156 3.521,2.354 0.458,0.198 10 false AM2 0.146,2.427 1.563,2.667 1.417,0.24 10 false from IG1 NO. 3 Relay 5.448,3.313 7.094,3.646 1.646,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 3.958,0.625 4.417,0.823 0.458,0.198 10 false F10 3.969,1.313 4.427,1.51 0.458,0.198 10 false F13 3.958,2 4.417,2.198 0.458,0.198 10 false F13 4.042,0.427 4.198,0.625 0.156,0.198 10 false 3 4.042,1.115 4.198,1.313 0.156,0.198 10 false 9 3.99,1.802 4.323,2.031 0.333,0.229 10 false 10 4.333,0.615 4.948,0.813 0.615,0.198 10 false IG1D 4.333,1.323 4.948,1.521 0.615,0.198 10 false ACCD 4.344,2.01 4.958,2.208 0.615,0.198 10 false +B 3.969,3.688 4.427,3.885 0.458,0.198 10 false F12 3.969,4.313 4.427,4.51 0.458,0.198 10 false F12 3.948,4.917 4.406,5.115 0.458,0.198 10 false F12 3.958,5.479 4.417,5.677 0.458,0.198 10 false F13 4,3.479 4.333,3.708 0.333,0.229 10 false 18 4.01,4.115 4.344,4.344 0.333,0.229 10 false 20 4.323,3.688 4.781,3.885 0.458,0.198 10 false RCO 4.323,4.313 4.865,4.552 0.542,0.24 10 false RDAM 4.323,4.906 4.865,5.146 0.542,0.24 10 false CSEL 3.99,4.719 4.323,4.948 0.333,0.229 10 false 19 3.99,5.281 4.323,5.51 0.333,0.229 10 false 11 4.354,5.49 4.51,5.688 0.156,0.198 10 false E 1.854,2.583 2.792,2.813 0.938,0.229 10 false IG1 NO. 3 1.646,3.125 1.958,3.323 0.313,0.198 10 false IG 1.604,3.677 2.219,3.875 0.615,0.198 10 false +5 1.448,4.281 2.063,4.479 0.615,0.198 10 false DATA 1.49,5.469 2.104,5.667 0.615,0.198 10 false GND 1.448,4.906 1.99,5.146 0.542,0.24 10 false CSEL 0.156,5.844 2.615,6.115 2.458,0.271 10 false Smart Door Control Receiver Assembly 5.552,4.875 6.979,5.083 1.427,0.208 10 false *1: for LHD 1.938,3.115 2.396,3.313 0.458,0.198 10 false M45 2.302,3.688 2.76,3.885 0.458,0.198 10 false M45 2.302,4.302 2.76,4.5 0.458,0.198 10 false M45 2.292,4.906 2.75,5.104 0.458,0.198 10 false M45 2.292,5.469 2.75,5.667 0.458,0.198 10 false M45 1.938,3.688 2.396,3.885 0.458,0.198 10 false M27 1.948,4.302 2.406,4.5 0.458,0.198 10 false M27 1.938,4.906 2.396,5.104 0.458,0.198 10 false M27 1.938,5.469 2.396,5.667 0.458,0.198 10 false M27 2,3.323 2.313,3.521 0.313,0.198 10 false *1 2.365,3.896 2.677,4.094 0.313,0.198 10 false *1 2.354,4.51 2.667,4.708 0.313,0.198 10 false *1 2.344,5.104 2.656,5.302 0.313,0.198 10 false *1 2.354,5.688 2.667,5.885 0.313,0.198 10 false *1 2,5.688 2.313,5.885 0.313,0.198 10 false *2 2.021,2.917 2.177,3.115 0.156,0.198 10 false 1 2.042,3.49 2.198,3.688 0.156,0.198 10 false 4 2.344,3.49 2.656,3.74 0.313,0.25 10 false 10 2.052,4.104 2.208,4.302 0.156,0.198 10 false 5 2.406,4.104 2.563,4.302 0.156,0.198 10 false 9 2.01,5.104 2.323,5.302 0.313,0.198 10 false *2 2.01,4.51 2.323,4.708 0.313,0.198 10 false *2 2.01,3.896 2.323,4.094 0.313,0.198 10 false *2 2.052,4.698 2.208,4.896 0.156,0.198 10 false 2 2.406,4.698 2.563,4.896 0.156,0.198 10 false 6 2.344,5.271 2.667,5.5 0.323,0.229 10 false 12 2.031,5.271 2.188,5.469 0.156,0.198 10 false 1 0.729,6.302 2.594,6.51 1.865,0.208 10 false : CAN Communication Line 5.552,5.292 6.979,5.5 1.427,0.208 10 false *2: for RHD 4,6.042 5.542,6.417 1.542,0.375 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to smart entry and start system (for Entry Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

·

When replacing the door control receiver assembly, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the Techstream and write them down before removal.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION

·

It is necessary to perform initialization (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the door control receiver if the door control receiver has been replaced.*

*: for LHD




PROCEDURE

1.INSPECT BATTERY VOLTAGE
a.

Measure the voltage of the vehicle battery.

Standard Voltage:

11 to 14 V


HINT:

It may be possible to tell whether the vehicle battery is discharged by operating the horn.

If the voltage is below 11 V, recharge or replace the vehicle battery before proceeding to the next step.



Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.


b.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.CHECK DOOR AJAR WARNING

B

3.CHECK DOOR AJAR WARNING
a.

When the doors are locked by operating the entry lock function with all doors closed, check that the door ajar warning operates.

HINT:

Warning function (door ajar warning)

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>SYSTEM DESCRIPTION



Result:
Result Proceed to
The wireless buzzer does not sound A
The wireless buzzer sounds B



A

4.CHECK POWER DOOR LOCK CONTROL SYSTEM

B

GO TO LIGHTING SYSTEM (Proceed to Door Courtesy Switch Circuit)

4.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the power window regulator master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Power door lock function operates normally A
Power door lock function does not operate normally B



A

5.CHECK KEY DIAGNOSTIC MODE

B

5.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antennas in key diagnostic mode.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143
i.
B358009C01
0.104,0.125 0.625,0.552 0.521,0.427 12 false *A 0.135,2.698 0.698,3.125 0.563,0.427 12 false *B 2.188,1.354 2.5,1.51 0.313,0.156 10 false *a 1.385,3.708 1.698,3.865 0.313,0.156 10 false *a
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (for driver door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




ii.
B358008C01
0.094,0.115 1.094,0.635 1,0.521 12 false *A 0.104,2.469 0.615,2.865 0.51,0.396 12 false *B 1.365,1.344 1.677,1.5 0.313,0.156 10 false *a 2.198,3.729 2.51,3.885 0.313,0.156 10 false *a
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (for front passenger door):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




iii.
B358003C02
0.677,1.104 2.323,0.208 2.323,0.208 2.5,0.208 false 1.792,1.115 2.323,0.208 false 2.583,0.115 2.896,0.271 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (front floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




iv.
B358004C01
0.656,0.292 2.198,0.115 2.198,0.115 2.354,0.115 false 1.792,0.281 2.177,0.115 false 2.427,0.042 2.74,0.198 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 2 indoor electrical key antenna assembly (rear floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




v.
B358015C03
1.229,1.396 2.333,0.427 2.333,0.427 2.542,0.427 false 1.667,1.292 2.323,0.438 false 2.646,0.323 2.958,0.479 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 3 indoor electrical key antenna assembly (inside luggage compartment):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.




vi.
B358005C02
1.885,1.313 2.198,1.469 0.313,0.156 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (outside luggage compartment):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage compartment), check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



OK:

Wireless buzzer sounds.




Result:
Result Proceed to
Diagnostic mode inspections fail for both channels A
Diagnostic mode inspections succeed for both channels B
Diagnostic mode inspection succeeds for only one of the channels C



A

6.CHECK WAVE ENVIRONMENT

B

18.PERFORM REGISTRATION

C

27.CHECK WAVE ENVIRONMENT
6.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly that was checked first near the smart door control receiver assembly and select the failed channel (the channel in which the buzzer did not sound) to recheck key diagnostic mode.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:
·

When the electrical key transmitter sub-assembly is brought near the smart door control receiver assembly, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.




Result:
Result Proceed to
The wireless buzzer does not sound A
The wireless buzzer sounds B



A

7.CHECK TRANSMITTER BATTERY

B

AFFECTED BY WAVE INTERFERENCE

7.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DATA LIST / ACTIVE TEST

·

Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly near the engine switch, depressing the brake pedal and pressing the engine switch.





Result:
Result Proceed to
Transmitter LED illuminates 3 times or more when switch is pressed and held A
Transmitter LED does not illuminate when switch is pressed and held B
Transmitter LED illuminates once or twice but not a third time C



A

8.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

17.INSPECT TRANSMITTER BATTERY

C

8.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.


Result:
Result Proceed to
Another registered electrical key transmitter sub-assembly is not available A
Another registered electrical key transmitter sub-assembly is available B



A

9.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

10.CHECK ENTRY LOCK OPERATION
9.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK ENTRY LOCK OPERATION
10.CHECK ENTRY LOCK OPERATION
a.

Using another registered electrical key transmitter sub-assembly, check that the entry lock and unlock functions operate.


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SMART DOOR CONTROL RECEIVER ASSEMBLY AND BODY GROUND)

B

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SMART DOOR CONTROL RECEIVER ASSEMBLY AND BODY GROUND)
a.

Disconnect the F12 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the M27*1 or M45*2 smart door control receiver assembly connector.

*1: for RHD

*2: for LHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
F12-18 (RCO) - M27-4 (+5) Always Below 1 Ω
F12-20 (RDAM) - M27-5 (DATA) Always Below 1 Ω
F12-19 (CSEL) - M27-2 (CSEL) Always Below 1 Ω
F12-18 (RCO) or M27-4 (+5) - Body ground Always 10 kΩ or higher
F12-20 (RDAM) or M27-5 (DATA) - Body ground Always 10 kΩ or higher
F12-19 (CSEL) or M27-2 (CSEL) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
F12-18 (RCO) - M45-10 (+5) Always Below 1 Ω
F12-20 (RDAM) - M45-9 (DATA) Always Below 1 Ω
F12-19 (CSEL) - M45-6 (CSEL) Always Below 1 Ω
F12-18 (RCO) or M45-10 (+5) - Body ground Always 10 kΩ or higher
F12-20 (RDAM) or M45-9 (DATA) - Body ground Always 10 kΩ or higher
F12-19 (CSEL) or M45-6 (CSEL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK ENTRY LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK ENTRY LOCK OPERATION
a.

Connect all connectors and check that the entry lock and unlock functions operate.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

13.INSPECT SMART DOOR CONTROL RECEIVER ASSEMBLY

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)

13.INSPECT SMART DOOR CONTROL RECEIVER ASSEMBLY
a.
B274837C62
1.5,0.375 1.885,0.646 0.385,0.271 1.521,2.469 1.927,2.729 0.406,0.26 2.052,1.271 2.344,1.896 false 1.385,3.604 0.99,4.135 false 1.375,1.281 0.99,1.875 false 1.833,3.594 2.24,4.146 false 0.427,0.104 0.635,0.302 0.208,0.198 10 false *A 0.417,2.042 0.625,2.24 0.208,0.198 10 false *B 0.781,0.427 0.99,0.625 0.208,0.198 10 false *a 0.813,2.521 1.021,2.719 0.208,0.198 10 false *a 1.573,0.427 1.979,0.625 0.406,0.198 10 false M27 2.208,1.906 2.625,2.104 0.417,0.198 10 false GND 1.594,2.51 1.948,2.708 0.354,0.198 10 false M45 0.802,4.156 1.219,4.354 0.417,0.198 10 false GND 0.823,1.896 1.24,2.094 0.417,0.198 10 false DATA 2.094,4.156 2.51,4.354 0.417,0.198 10 false DATA
*A for RHD
*B for LHD
*a Component with harness connected
(Smart Door Control Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
M27-1 (GND) - Body ground Always Below 1 Ω

for LHD
Tester Connection Condition Specified Condition
M45-12 (GND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RHD
Tester Connection Condition Specified Condition
M27-5 (DATA) - M27-1 (GND) Procedure:
1.

All doors closed

2.

All doors locked

3.

Lock or unlock switch of electrical key transmitter sub-assembly pressed


Below 1 V → Pulse generation

for LHD
Tester Connection Condition Specified Condition
M45-9 (DATA) - M45-12 (GND) Procedure:
1.

All doors closed

2.

All doors locked

3.

Lock or unlock switch of electrical key transmitter sub-assembly pressed


Below 1 V → Pulse generation



Result:
Result Proceed to
OK A
NG (for RHD) B
NG (for LHD) C



A

14.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

C

REPLACE ELECTRICAL KEY AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY

14.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B274837C63
1.5,0.375 1.885,0.646 0.385,0.271 1.521,2.469 1.927,2.729 0.406,0.26 2.052,1.271 2.719,1.865 false 1.385,3.604 0.99,4.135 false 1.563,1.281 1.177,1.875 false 1.677,3.615 2.24,4.146 false 1.896,1.281 2.24,1.865 false 1.354,3.385 0.74,3.802 false 2.094,3.385 2.656,3.917 false 0.427,0.104 0.635,0.302 0.208,0.198 10 false *A 0.417,2.042 0.625,2.24 0.208,0.198 10 false *B 0.781,0.427 0.99,0.625 0.208,0.198 10 false *a 0.813,2.521 1.021,2.719 0.208,0.198 10 false *a 1.573,0.427 1.979,0.625 0.406,0.198 10 false M27 2.615,1.885 3.031,2.083 0.417,0.198 10 false GND 1.615,2.521 1.969,2.719 0.354,0.198 10 false M45 0.802,4.156 1.219,4.354 0.417,0.198 10 false GND 1.104,1.885 1.521,2.083 0.417,0.198 10 false +5 2.208,4.146 2.625,4.344 0.417,0.198 10 false +5 2.125,1.885 2.583,2.156 0.458,0.271 10 false CSEL 0.573,3.813 0.99,4.01 0.417,0.198 10 false CSEL 2.625,3.938 2.885,4.188 0.26,0.25 10 false IG
*A for RHD
*B for LHD
*a Component with harness connected
(Smart Door Control Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RHD
Tester Connection Condition Specified Condition
M27-4 (+5) - M27-1 (GND) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly switch not pressed → pressed


Below 1 V → 4.5 to 6.0 V → Below 1 V
M27-2 (CSEL) - M27-1 (GND) Procedure:
1.

Engine switch off

2.

All doors closed


Below 1 V → Pulse generation

for LHD
Tester Connection Condition Specified Condition
M45-1 (IG) - M45-12 (GND) Engine switch on (IG) 10 to 16 V
M45-10 (+5) - M45-12 (GND) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly switch not pressed → pressed


Below 1 V → 4.5 to 6.0 V → Below 1 V
M45-6 (CSEL) - M45-12 (GND) Procedure:
1.

Engine switch off

2.

All doors closed


Below 1 V → Pulse generation



Result:
Proceed to
OK
NG



OK

15.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

15.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) and perform registration again.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

16.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
16.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

17.INSPECT TRANSMITTER BATTERY
a.

Inspect the transmitter battery.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

18.PERFORM REGISTRATION
a.

Perform registration of the B code.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

19.CHECK ENTRY LOCK OPERATION
19.CHECK ENTRY LOCK OPERATION
a.

After B code registration is complete, check that the entry lock and unlock functions operate.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

20.READ VALUE USING GTS (B CODE)

B

END (B CODE REGISTRATION FAILED)

20.READ VALUE USING GTS (B CODE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
B Code B code registration status Regd or No Regd Regd: B code registered correctly
No Regd: B code not registered correctly
-
Body Electrical > Entry&Start > Data List
Tester Display
B Code
50003 125 132

Result:
Result Proceed to
"No Regd" is displayed on the GTS A
"Regd" is displayed on the GTS B



A

21.READ VALUE USING GTS (B CODE DIFFERENCE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

21.READ VALUE USING GTS (B CODE DIFFERENCE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
B Code Difference B code mismatch Yes or No Yes: Communication malfunction
No: Communication normal
-
Body Electrical > Entry&Start > Data List
Tester Display
B Code Difference
50003 125 131

Result:
Result Proceed to
"No" is displayed on the GTS A
"Yes" is displayed on the GTS B



A

22.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

22.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Measure the voltage while checking the Data List on the GTS.

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Body Electrical / Power Source Control / Data List.


v.

Read the Data List according to the display on the GTS.

B344851C11
1.677,0.333 2.052,0.573 0.375,0.24 5.125,0.333 5.5,0.573 0.375,0.24 3.344,0.333 3.719,0.573 0.375,0.24 1.031,2.063 1.365,1.219 false 4.667,1.25 4.792,2.156 false 0.844,2.125 1.25,2.313 0.406,0.188 10 false IG1D 1.76,0.365 2.167,0.552 0.406,0.188 10 false F10 4.635,2.198 5.042,2.385 0.406,0.188 10 false ACCD 5.229,0.365 5.635,0.552 0.406,0.188 10 false F13 0.188,0.125 0.594,0.313 0.406,0.188 10 false *a 3.438,0.365 3.844,0.552 0.406,0.188 10 false F12
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state All OFF, ACC ON, IG ON or ST ON All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC)
IG ON: Engine switch on (IG)
ST ON: Sending engine start request signal
-
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18
Standard Voltage:
Tester Connection Condition Specified Condition
F10-3 (IG1D) - Body ground Engine switch off Below 1 V
Engine switch on (ACC) Below 1 V
Engine switch on (IG) 9 V or higher
F13-9 (ACCD) - Body ground Engine switch off Below 1 V
Engine switch on (ACC) 9 V or higher
Engine switch on (IG) 9 V or higher




Result:
Proceed to
OK
NG



OK

23.READ VALUE USING GTS (ACC SW, IG SW)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

23.READ VALUE USING GTS (ACC SW, IG SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW Engine switch status ON or OFF ON: Engine switch on (ACC)
OFF: Engine switch off
"ON" is displayed even though the engine switch is on (IG).
IG SW Engine switch status ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
"OFF" is displayed even though the engine switch is on (ACC).
Body Electrical > Main Body > Data List
Tester Display
ACC SW
IG SW
50003 123 31,30
HINT:

If the certification ECU (smart key ECU assembly) misjudges for any reason that the engine switch is on (IG) even though the engine switch is off, the entry lock and unlock functions stop.



Result:
Result Proceed to
The main body ECU (multiplex network body ECU) judges properly that the power source is off when the engine switch is off A
The main body ECU (multiplex network body ECU) does not judge properly that the power source is off when the engine switch is off B



A

24.CHECK ENTRY LOCK OPERATION

B

24.CHECK ENTRY LOCK OPERATION
a.

Disconnect and reconnect the certification ECU (smart key ECU assembly) connector.



Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

25.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)

25.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and perform registration again.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

26.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
26.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

27.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly that was checked first near the smart door control receiver assembly and select the failed channel (the channel in which the buzzer did not sound) to recheck key diagnostic mode.

HINT:
·

When the electrical key transmitter sub-assembly is brought near the smart door control receiver assembly, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.




Result:
Result Proceed to
The wireless buzzer does not sound A
The wireless buzzer sounds B



A

28.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

AFFECTED BY WAVE INTERFERENCE

28.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.


Result:
Result Proceed to
Another registered electrical key transmitter sub-assembly is not available A
Another registered electrical key transmitter sub-assembly is available B



A

29.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

30.CHECK WAVE ENVIRONMENT
29.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

30.CHECK WAVE ENVIRONMENT
30.CHECK WAVE ENVIRONMENT
a.

Bring another registered electrical key transmitter sub-assembly near the smart door control receiver assembly and select the failed channel (the channel in which the buzzer did not sound) to recheck key diagnostic mode.

HINT:
·

When the electrical key transmitter sub-assembly is brought near the smart door control receiver assembly, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.




Result:
Result Proceed to
The wireless buzzer does not sound A
The wireless buzzer sounds B



A

31.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SMART DOOR CONTROL RECEIVER ASSEMBLY)

B

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

31.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SMART DOOR CONTROL RECEIVER ASSEMBLY)
a.

Disconnect the F12 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the M27*1 or M45*2 smart door control receiver assembly connector.

*1: for RHD

*2: for LHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
F12-19 (CSEL) - M27-2 (CSEL) Always Below 1 Ω
F12-19 (CSEL) or M27-2 (CSEL) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
F12-19 (CSEL) - M45-6 (CSEL) Always Below 1 Ω
F12-19 (CSEL) or M45-6 (CSEL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

32.CHECK ENTRY LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

32.CHECK ENTRY LOCK OPERATION
a.

Connect all connectors and check that the entry lock and unlock functions operate.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

33.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

END (CONNECTOR WAS NOT CONNECTED SECURELY)

33.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B274837C64
1.5,0.375 1.885,0.646 0.385,0.271 1.521,2.469 1.927,2.729 0.406,0.26 2.052,1.271 2.344,1.896 false 1.385,3.604 0.99,4.135 false 1.844,1.281 1.344,1.906 false 0.76,3.833 1.365,3.396 false 0.427,0.104 0.635,0.302 0.208,0.198 10 false *A 0.417,2.042 0.625,2.24 0.208,0.198 10 false *B 0.781,0.427 0.99,0.625 0.208,0.198 10 false *a 0.813,2.521 1.021,2.719 0.208,0.198 10 false *a 1.573,0.427 1.979,0.625 0.406,0.198 10 false M27 2.208,1.906 2.625,2.104 0.417,0.198 10 false GND 1.594,2.51 1.948,2.708 0.354,0.198 10 false M45 0.802,4.156 1.219,4.354 0.417,0.198 10 false GND 1.198,1.917 1.615,2.115 0.417,0.198 10 false CSEL 0.573,3.854 0.99,4.052 0.417,0.198 10 false CSEL
*A for RHD
*B for LHD
*a Component with harness connected
(Smart Door Control Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RHD
Tester Connection Condition Specified Condition
M27-2 (CSEL) - M27-1 (GND) Procedure:
1.

Engine switch off

2.

All doors closed


Below 1 V → Pulse generation

for LHD
Tester Connection Condition Specified Condition
M45-6 (CSEL) - M45-12 (GND) Procedure:
1.

Engine switch off

2.

All doors closed


Below 1 V → Pulse generation



Result:
Proceed to
OK
NG



OK

34.INSPECT SMART DOOR CONTROL RECEIVER ASSEMBLY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

34.INSPECT SMART DOOR CONTROL RECEIVER ASSEMBLY
a.

Enter key diagnostic mode and select the channel for which the wireless buzzer did not sound.


b.
B274837C65
1.5,0.375 1.885,0.646 0.385,0.271 1.521,2.469 1.927,2.729 0.406,0.26 2.052,1.271 2.344,1.896 false 1.385,3.604 0.99,4.135 false 1.375,1.281 0.99,1.875 false 1.833,3.594 2.24,4.146 false 0.427,0.104 0.635,0.302 0.208,0.198 10 false *A 0.417,2.042 0.625,2.24 0.208,0.198 10 false *B 0.781,0.427 0.99,0.625 0.208,0.198 10 false *a 0.813,2.521 1.021,2.719 0.208,0.198 10 false *a 1.573,0.427 1.979,0.625 0.406,0.198 10 false M27 2.208,1.906 2.625,2.104 0.417,0.198 10 false GND 1.604,2.51 1.958,2.708 0.354,0.198 10 false M45 0.802,4.156 1.219,4.354 0.417,0.198 10 false GND 0.823,1.896 1.24,2.094 0.417,0.198 10 false DATA 2.094,4.156 2.51,4.354 0.417,0.198 10 false DATA
*A for RHD
*B for LHD
*a Component with harness connected
(Smart Door Control Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RHD
Tester Connection Condition Specified Condition
M27-5 (DATA) - M27-1 (GND) Procedure:
1.

All doors closed

2.

All doors locked

3.

Lock or unlock switch of electrical key transmitter sub-assembly pressed


Below 1 V → Pulse generation

for LHD
Tester Connection Condition Specified Condition
M45-9 (DATA) - M45-12 (GND) Procedure:
1.

All doors closed

2.

All doors locked

3.

Lock or unlock switch of electrical key transmitter sub-assembly pressed


Below 1 V → Pulse generation


HINT:

Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).



Result:
Result Proceed to
OK A
NG (for RHD) B
NG (for LHD) C



A

35.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

C

REPLACE ELECTRICAL KEY AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY

35.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) and perform registration again.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

36.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
36.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock function operates normally A
Wireless door lock function does not operate normally B



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)