Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › from 2016.11
RM3160E _59 Vehicle Exterior _019717 WINDOW / GLASS _0106118 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the windshield glass of a vehicle equipped with a lane departure warning camera, make sure to use a Toyota genuine part. The lane departure warning camera may not be able to be installed due to a missing bracket or the lane departure alert system may not operate properly due to a difference in the transmissivity or black ceramic border.


PROCEDURE

Hide 85292B 1.REMOVE FRONT WIPER ARM HEAD CAP

Hide 2.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 3.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 53867H 4.REMOVE FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 5.REMOVE FRONT FENDER TO COWL SIDE SEAL RH

Hide 55781E 6.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 75534 7.REMOVE WINDSHIELD OUTSIDE MOULDING LH

Hide 75533 8.REMOVE WINDSHIELD OUTSIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.


Hide 87810 9.REMOVE INNER REAR VIEW MIRROR ASSEMBLY

Hide 89941 10.REMOVE RAIN SENSOR (w/ Rain Sensor)

Hide 8646C 11.REMOVE FORWARD RECOGNITION CAMERA (w/ Lane Departure Alert System)

Hide 12.REMOVE ROOF HEADLINING ASSEMBLY

Hide 56111 13.REMOVE WINDSHIELD GLASS SUB-ASSEMBLY

a.

w/ Windshield Deicer System:

i.
B362414

Disconnect the connector and disengage the clamp.



b.
B361151C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the area around the installation position of the windshield glass sub-assembly on the vehicle body to prevent it from being scratched.


c.
B361295C01
1.875,0.677 2.156,0.438 false 2.188,0.333 2.5,0.49 0.313,0.156 10 false *a
*a Cut Off


Using a knife, cut off the windshield outside moulding as shown in the illustration.


d.
B361296C01
1.635,0.323 0.5,0.323 false 1.625,0.667 1.375,0.667 1.375,0.667 1.375,0.333 true 0.333,0.229 0.646,0.385 0.313,0.156 10 false *a
*a Matchmark


Place matchmarks on the windshield glass sub-assembly and vehicle body on the locations indicated in the illustration.

HINT:

Matchmarks are not necessary if the windshield glass sub-assembly is not going to be reused.



e.
B361297C01
1.177,0.406 1.719,0.969 1.719,0.969 2.198,0.406 true 1.094,1.292 1.385,1.458 false 1.667,1.01 1.979,1.167 0.313,0.156 10 false *1 1.427,1.365 1.74,1.521 0.313,0.156 10 false *a
*1 Windshield Glass Stopper
*a Piano Wire


Pass a piano wire between the vehicle body and windshield glass sub-assembly from the interior.


f.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.


g.

Cut off the adhesive by pulling the piano wire around the windshield glass sub-assembly.

NOTICE:
·

When separating the windshield glass sub-assembly, be careful not to damage the paint or interior and exterior ornaments.

·

To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.




h.

Disengage the windshield glass stoppers.

B361298C01
1.969,0.625 2.125,0.833 false 5.26,0.396 5.604,0.198 false 5.042,0.521 5.042,0.854 5.042,0.854 5.375,0.854 false 5.25,0.854 5.25,0.688 false 5.146,0.854 5.135,0.521 false 1.302,0.125 1.625,0.438 0.323,0.313 12 false *A 4.51,0.125 4.885,0.427 0.375,0.302 12 false *B 2.156,0.74 2.469,0.896 0.313,0.156 10 false *1 5.667,0.094 5.979,0.25 0.313,0.156 10 false *2 5.396,0.76 5.708,0.917 0.313,0.156 10 false *1
*A for 1-piece Type *B for 2-piece Type
*1 No. 1 Windshield Glass Stopper *2 No. 2 Windshield Glass Stopper


NOTICE:
·

The No. 1 windshield glass stoppers and No. 2 windshield glass stoppers are installed on the windshield glass sub-assembly as shown in the illustration. Be careful not to damage the windshield glass sub-assembly when cutting off the adhesive.

·

To prevent the windshield glass from falling when performing this operation, be sure to hold the windshield glass using suction cups.



HINT:

Depending on the vehicle, either 1-piece type or 2-piece type stoppers may be present.



i.

Using suction cups, remove the windshield glass sub-assembly.

NOTICE:
·

Be careful not to drop the windshield glass sub-assembly.

·

Leave as much adhesive on the vehicle body as possible when removing the windshield glass sub-assembly.




Hide 56117A 14.REMOVE WINDOW GLASS ADHESIVE DAM

a.

When reusing the windshield glass:

i.
B361299C01
0.104,0.104 0.531,0.469 0.427,0.365 12 false *A
*A Back Side


Using a scraper, remove the window glass adhesive dam from the back side of the windshield glass.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the window glass adhesive dam with a new one.





Hide 15.REMOVE WINDSHIELD OUTSIDE MOULDING

a.

When reusing the windshield glass:

i.
B361324C01
0.115,0.104 0.479,0.396 0.365,0.292 12 false *A
*A Back Side


Using a scraper, remove the windshield outside moulding from the back side of the windshield glass.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the windshield outside moulding with a new one.





Hide 16.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)

a.

When reusing the windshield glass:

i.
B361300C01
0.104,0.104 0.438,0.406 0.333,0.302 12 false *A
*A Back Side


Using a scraper, remove the 2 No. 1 windshield glass stoppers from the back side of the windshield glass.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the 1-piece type No. 1 windshield glass stoppers with new 2-piece type No. 1 and No. 2 windshield glass stoppers.





Hide 56116C 17.REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.

When reusing the windshield glass:

i.
B361300C01
0.104,0.104 0.438,0.406 0.333,0.302 12 false *A
*A Back Side


Using a scraper, remove the 2 No. 2 windshield glass stoppers from the back side of the windshield glass.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the No. 2 windshield glass stoppers with new ones.





Hide 56115A 18.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B361301

Remove the 2 No. 1 windshield glass stoppers from the vehicle body.

NOTICE:

Be sure to replace the No. 1 windshield glass stoppers with new ones.



Hide 19.CLEAN WINDSHIELD GLASS

a.

When reusing the windshield glass:

i.
B149736

Using a scraper, remove any remaining adhesive dam and adhesive residue from the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.



ii.

Clean the outer circumference of the windshield glass with a non-residue solvent.

NOTICE:
·

Do not touch the windshield glass surface after cleaning it.

·

Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.





Hide 20.CLEAN VEHICLE BODY

a.

Clean and shape the contact surface of the vehicle body.

i.
B361302C01
0.74,0.885 0.469,0.573 false 0.281,0.5 0.594,0.656 0.313,0.156 10 false *a 1.802,1.083 1.958,1.281 0.156,0.198 10 false a
*a Vehicle Body
V100155

Adhesive


Using a knife, cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.

Standard Dimension:
Area Dimension
a 1.0 mm (0.0394 in.)


NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave approximately 1.0 mm (0.0394 in.) of adhesive on the vehicle body.



ii.

Clean the contact surface of the vehicle body with a piece of cloth saturated with non-residue solvent.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.