When replacing the windshield glass of a vehicle equipped with a lane departure warning camera, make sure to use a Toyota genuine part. The lane departure warning camera may not be able to be installed due to a missing bracket or the lane departure alert system may not operate properly due to a difference in the transmissivity or black ceramic border.
56115A
1.INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)
Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.
Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.
56116C
2.INSTALL NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)
Using a brush or sponge, coat the application area of 2 new No. 2 windshield glass stoppers with primer G.
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
| *A | Back Side |
| *a | Ceramic Notch |
| *b | Windshield Glass Edge Side |
Install the 2 new No. 2 windshield glass stoppers onto the windshield glass as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 14.0 mm (0.551 in.) |
Only 2-piece type windshield glass stoppers are provided as supply parts. Use the 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.
3.INSTALL WINDSHIELD OUTSIDE MOULDING
Using a brush or sponge, coat the application area of a new windshield outside moulding with primer G.
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
| *A | Back Side |
|
Edge Of Curved Surface |
Install the new windshield outside moulding to the windshield glass as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 7.0 mm (0.276 in.) |
56117A
4.INSTALL WINDOW GLASS ADHESIVE DAM
| *a | Cut |
Cut the window glass adhesive dam so that it is the appropriate size as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 302.5 cm (9.92 ft.) |
Using a brush or sponge, coat the application area of a new window glass adhesive dam with primer G.
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
Install the window glass adhesive dam to the windshield glass as shown in the illustration.
| *A | Back Side | - | - |
| *a | Adhesive positioning ceramic notch | *b | window glass adhesive dam positioning center line |
|
Primer G | - | - |
| Area | Dimension |
|---|---|
| a | 6.5 mm (0.256 in.) |
56111
5.INSTALL WINDSHIELD GLASS SUB-ASSEMBLY
| *a | Matchmark |
Position the windshield glass sub-assembly.
Using suction cups, place the windshield glass sub-assembly in the correct position.
Check that the whole contact surface of the windshield glass sub-assembly rim is perfectly even.
Align the matchmarks on the windshield glass sub-assembly and vehicle body.
Check that the windshield glass stoppers are attached to the vehicle body correctly.
Remove the windshield glass sub-assembly.
Using a brush, coat the installation surface on the vehicle body with primer M.
Do not coat the adhesive with primer M.
Do not apply too much primer M.
Allow the primer M to dry for 3 minutes or more.
Throw away any leftover primer M.
If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.
Using a brush or sponge, coat the application area of adhesive with primer G.
| *A | Back Side | - | - |
|
Primer G | - | - |
| Area | Dimension |
|---|---|
| a | 8.0 mm (0.315 in.) or more. |
| b | 16.0 mm (0.630 in.) or more. |
| c | 8.0 mm (0.315 in.) or more. |
Do not apply too much primer G.
Allow the primer G to dry for 3 minutes or more.
Throw away any leftover primer G.
Apply primer G onto the ceramic notches.
If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.
Apply adhesive to the windshield glass sub-assembly.
Toyota Genuine Windshield Glass Adhesive or equivalent
| *a | Nozzle |
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 12.0 mm (0.472 in.) or more |
| b | 8.0 mm (0.315 in.) or more |
Load the sealer gun with the cartridge.
Apply adhesive to the windshield glass sub-assembly as shown in the illustration.
| *A | Back Side | - | - |
| *a | Adhesive positioning ceramic notch | *b | Adhesive positioning center line |
|
Adhesive | - | - |
Apply adhesive onto the ceramic notches.
| *a | Matchmark |
Install the windshield glass sub-assembly.
Using suction cups, position the windshield glass sub-assembly so that the matchmarks are aligned, and press it in gently along the rim.
Check that the windshield glass stoppers are attached to the vehicle body correctly.
Check the clearance between the vehicle body and windshield glass sub-assembly.
Lightly press the front surface of the windshield glass sub-assembly to ensure that the windshield glass is securely fit to the vehicle body.
Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.
Using a scraper, remove any excess or protruding adhesive.
Hold the windshield glass using protective tape until the applied adhesive becomes hard.
Do not drive the vehicle for the time described in the table below.
| Temperature | Minimum Time prior to Driving Vehicle |
|---|---|
| 35°C (95°F) | 1 hour and 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
w/ Windshield Deicer System:
Engage the clamp and connect the connector.
6.INSPECT FOR LEAK
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
7.INSTALL ROOF HEADLINING ASSEMBLY
8646C
8.INSTALL FORWARD RECOGNITION CAMERA (w/ Lane Departure Alert System)
89941
9.INSTALL RAIN SENSOR (w/ Rain Sensor)
87810
10.INSTALL INNER REAR VIEW MIRROR ASSEMBLY
75534
11.INSTALL WINDSHIELD OUTSIDE MOULDING LH
75533
12.INSTALL WINDSHIELD OUTSIDE MOULDING RH
Use the same procedure as for the LH side.
55781E
13.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
53867H
14.INSTALL FRONT FENDER TO COWL SIDE SEAL LH
53866J
15.INSTALL FRONT FENDER TO COWL SIDE SEAL RH
16.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
17.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
85292B
18.INSTALL FRONT WIPER ARM HEAD CAP