Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › from 2016.11
RM3160E _58 Vehicle Interior _019707 LIGHTING (INT) _0103507 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Engine Switch Illumination Circuit  


DESCRIPTION

The illuminated entry system controls the engine switch illumination.

WIRING DIAGRAM

E287409E01
2.958,1.177 3.448,1.396 0.49,0.219 10 false AGND 3,0.771 3.417,0.938 0.417,0.167 10 false SWIL 4.74,1.26 5.229,1.479 0.49,0.219 10 false AGND 4.729,0.885 5.146,1.052 0.417,0.167 10 false SWIL 3.458,0.771 3.698,0.948 0.24,0.177 10 false 9 4.469,1.177 4.708,1.354 0.24,0.177 10 false 12 4.458,0.771 4.698,0.948 0.24,0.177 10 false 17 3.458,1.177 3.698,1.354 0.24,0.177 10 false 6 1.781,1.74 2.24,1.938 0.458,0.198 10 false F49 4.406,1.677 4.865,1.875 0.458,0.198 10 false F13 1.781,1.885 2.76,2.104 0.979,0.219 10 false Engine Switch 4.406,1.844 6.219,2.24 1.813,0.396 10 false Certification ECU (Smart Key ECU Assembly)

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power/Engine SW Light Engine switch illumination OFF or ON When performing this Active Test, make sure the following condition is met:
The engine switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the ignition switch is ON or ACC, or the engine is running.
Body Electrical > Entry&Start > Active Test
Tester Display
Power/Engine SW Light
50004 125 27
OK:

Engine switch illumination comes on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT ENGINE SWITCH
2.INSPECT ENGINE SWITCH


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the F13 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F49-9 (SWIL) - F13-17 (SWIL) Always Below 1 Ω
F49-6 (AGND) - F13-12 (AGND) Always Below 1 Ω
F49-9 (SWIL) or F13-17 (SWIL) - Body ground Always 10 kΩ or higher
F49-6 (AGND) or F13-12 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR